This Sources Sought opportunity from Department Of Commerce was posted on July 1, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.

Top

Sources Sought Wirebond Pull Tester

Awarded

NB687000-26-02180Federal

Submission Closed07/09/2026, 05:00:00 PM UTC

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

Active Opportunities Like This One

Solicitation # SPE7M1-27-T-1744

DLA WEAPONS SUPPORT MARITIME SUPPLY CHAIN

POSTED

DEADLINE

4 Series Mixed Signal Oscilloscope (MSO44B)

Solicitation # 80NSSC27941006Q

NASA/NSSC is seeking capability statements for the acquisition of a Tektronix MSO44B 4 Series Mixed Signal Oscilloscope and associated accessories to support embedded hardware bring-up, board-level debug, and signal integrity analysis at the NASA Ames Research Center in California. The required equipment must feature four analog input channels, 1 GHz bandwidth, a minimum record length of 31.25 M points per channel, and a perpetual, node-locked ultimate software bundle for advanced analysis. Additional requirements include an 8-channel logic probe, various specialized voltage and current probes using a common interface, a hard transit case, and a five-year calibration service with traceable certification. The government intends to issue a sole source contract to Tektronix under FAR 12.102(a), as they have been determined to be the sole provider of this specific oscilloscope. This procurement is being conducted as an acquisition of commercial items under FAR Part 12, and NASA FAR Supplement Clause 1852.215-84 regarding the Ombudsman is applicable. Interested vendors must submit written capability statements by October 30, 2026, referencing the notice ID. These statements will be used solely to determine if the procurement will be conducted on a competitive basis; formal quotes will not be evaluated at this stage.

National Aeronautics And Space Administration

POSTED

DEADLINE

Supply of Indicating Thermometer (NSN 6685-01-115-8407)This subcontract involves the procurement or manufacture of one capillary tube indicating thermometer under NSN 6685-01-115-8407 for the DLA Weapons Support ASC Supplier Oper OEM Division. The contractor must ensure the device is mercury-free in accordance with IP056 and adheres to MIL-STD-129 marking requirements. Packaging must be handled as a delicate instrument following MIL-STD-2073-1E and RP001 standards. The final product is to be delivered FOB Destination to the USS GETTYSBURG CG 64. This requirement falls under NAICS code 334515 and is managed by the Department of Defense. The response deadline for this action is November 4, 2026.

DLA WEAPONS SUPPORT ASC SUPPLIER OPER OEM DIVISION

POSTED

DEADLINE

Solicitation # SPE4A5-26-T-050Y

This solicitation, issued by the Department of Defense ASC Supplier Oper OEM Division, is for the procurement of six Discharge Indicators under NSN 6625-01-527-4524. The contract requires delivery within 171 days after the order is placed, with performance located at Robins Air Force Base. The solicitation is categorized under NAICS code 334515 and is managed by point of contact Rasulbek Kilichev. The agreement incorporates specific DLA packaging and technical requirements, including RP001 and RA001, which are detailed in the DLA Master List of Technical and Quality Requirements. Additionally, requirement RQ011 mandates the removal of government identification from any non-accepted supplies. Alternate offerors are specifically required to submit a complete data package containing information for both the approved and alternate parts.

ASC SUPPLIER OPER OEM DIVISION

POSTED

DEADLINE

Solicitation # SPE7M1-27-U-0790

Solicitation SPE7M1-27-U-0790 is a HUBZone set-aside request for quotations issued by the DLA Weapons Support Maritime Supply Chain for the procurement of four special scale meters, identified by NSN 6625013224225. This requirement may result in a unilateral Indefinite Delivery Contract for a one-year period with a maximum contract value of 350,000.00 dollars. The delivery timeline is 70 days after order, with shipping handled under the First Destination Transportation program and FOB Origin terms. Both inspection and acceptance will occur at the destination. The contractor must adhere to strict technical and quality standards, including MIL-STD-2073-1E for packaging and MIL-STD-129 for marking. Special attention is required for hazardous materials, specifically regarding the restriction of mercury and the necessity of hazard warning labels and Material Safety Data Sheets. Compliance with the Buy American Act, Berry Amendment, and DFARS cybersecurity standards is mandatory. All payment requests and receiving reports must be processed electronically through the Wide Area WorkFlow system. Quotations are due by October 27, 2026, and must be submitted using Form SF18.

DLA WEAPONS SUPPORT MARITIME SUPPLY CHAIN

POSTED

DEADLINE

Solicitation # SPE7M1-27-U-0794

Solicitation SPE7M1-27-U-0794 is a Total Small Business Set-Aside issued by the DLA Weapons Support Maritime Supply Chain for the procurement of digital test benches, specifically Fluke Corp part number 1550C (NSN 6625-01-588-7039). This is a unilateral Simplified Indefinite-Delivery Contract (SIDC) with a maximum value of 350,000.00 USD for a one-year period. The estimated annual quantity is 28 units, with a guaranteed contract minimum of 4 units and a minimum delivery order quantity of 3 units. Delivery is required within 83 days after order, with FOB Origin terms and inspection and acceptance occurring at the destination. The items are identified as Commercial Off-The-Shelf (COTS) and are designated as critical application items. Compliance with several technical and quality standards is mandatory, including MIL-STD-2073-1E for packaging, MIL-STD-129 for marking, and DLA packaging requirements RP001. The contract strictly prohibits the intentional addition of mercury, except in specific functional components, and requires adherence to the Hazard Communication Standard for any hazardous materials. Additionally, the contractor must comply with the Buy American and Balance of Payments Program, CMMC Level 2 self-assessment requirements, and Covered Defense Information protocols. Invoicing and payment are processed electronically through the Wide Area WorkFlow system.

DLA WEAPONS SUPPORT MARITIME SUPPLY CHAIN

POSTED

DEADLINE

Solicitation # RFQ497626

UT-Battelle, LLC, acting as the management and operating contractor for Oak Ridge National Laboratory, has issued solicitation RFQ497626 for the procurement of a dual-channel 200V sourcemeter system (Part Number 2612B) and an associated power cord (Part Number PWRKI). The requirement is managed by the Neutron Sciences Division and is categorized under NAICS code 334515. Responses are due by November 3, 2026, and the procurement is based in Oak Ridge, Tennessee. The contract incorporates extensive federal and agency-specific regulations, including FAR and DEAR clauses. Key compliance requirements include the Buy American Act for supplies exceeding the micro-purchase threshold and strict adherence to Department of Energy cybersecurity and privacy programs, specifically DOE O 205.1D and NIST SP 800-171 for protecting controlled unclassified information. Depending on the final contract value, additional regulations regarding anti-kickback procedures, veteran employment reporting, and subcontractor sales restrictions may apply. Offerors must provide a Unique Entity ID via SAM.gov and complete abbreviated representations and certifications, including socioeconomic status and lobbying disclosures.

Ornl Ut-Battelle Llc-Doe Contractor

POSTED

DEADLINE

Torque Calibration System Upgrade 250 ft-lbf

Solicitation # 27M-349A-TQ

FA2263 Aflcmc Romk Afmetcal

POSTED

DEADLINE

Notice of Intent - Control Laser Corp

Solicitation # SHOP-PR-27-000055

Federal Bureau Of Investigation

POSTED

DEADLINE

Solicitation # SPE7M1-27-T-1632

Solicitation SPE7M1-27-T-1632 is a small business set-aside issued by the DLA Weapons Support Maritime Supply Chain for the procurement of one test fixture, identified as NSN 6625-01-126-4886 and part number 61690-090 from Dynalec Corporation. This item is designated as a critical application item. The required delivery date is June 19, 2027, with a delivery lead time of 224 days after order. Delivery is to be made FOB Destination to the DLA Distribution DDSP New Cumberland Facility in Pennsylvania. The contract mandates strict adherence to quality and technical standards, incorporating the DLA Master List of Technical and Quality Requirements (RA001) and specific packaging requirements under RP001 and MIL-STD-2073-1E. Marking must comply with MIL-STD-129. Special provisions are included for the handling of batteries and the prohibition of intentionally added mercury, per NAVSEA 5100-003D. Invoicing and payment must be processed electronically through the Wide Area WorkFlow (WAWF) system. Compliance requirements include the Buy American Act, the Berry Amendment, and various DFARS clauses regarding cybersecurity, specifically the safeguarding of covered defense information and the prohibition of certain telecommunications equipment. Inspection and acceptance will occur at the destination. Offerors are instructed to submit quotes via the DIBBS portal based on FOB Origin and are encouraged to provide quantity ranges due to volatile demand.

DLA WEAPONS SUPPORT MARITIME SUPPLY CHAIN

POSTED

DEADLINE

Keysight Network Analyzer

Solicitation # HQ072727QMH02

The Defense Microelectronics Activity is issuing solicitation HQ072727QMH02 as a resolicitation to acquire a Keysight N5222B-219 Vector Network Analyzer. This 2-Port 10 MHz to 26.5 GHz Performance Network Analyzer must include a configurable test set, reference mixer switch, source and receiver attenuators, and bias tees. The equipment is essential for the DMEA to measure, test, and analyze the electrical performance of radio frequency and microwave components, such as antennas, cables, and amplifiers, in support of Technical Data Package project requirements. This is a sole-source procurement under FAR 13.106-1(b)(1)(i), as market research determined that only Keysight Technologies Inc can provide the specific N5222B-219 configuration. A critical requirement of this acquisition is that the equipment be sourced directly from the manufacturer to ensure the firmware remains unmodified by third-party vendors. The procurement is managed by Michael Hallock and is categorized under NAICS code 334515, with performance taking place in California. The response deadline for this combined solicitation is November 2, 2026.

Defense Microelectronics Activity

POSTED

DEADLINE

Supply of Multimovement Electrical MetersThis subcontract involves the supply of 15 multimovement electrical meters to prime contractors supporting the Defense Logistics Agency Weapons Support Maritime Supply Chain. The hardware must strictly adhere to NSN 6625012782223 specifications, with mandatory marking and packaging compliance according to MIL-STD-129 and MIL-STD-2073-1E standards. Additionally, the provider must comply with all defense telecommunications equipment representations. The project falls under NAICS code 334515 and is managed by the Department of Defense. Performance of the contract will take place in New Cumberland, Pennsylvania. Interested parties should note the response deadline of November 5, 2026.

DLA WEAPONS SUPPORT MARITIME SUPPLY CHAIN

POSTED

3 days ago

DEADLINE

in 8 days

AI Contract Overview

The National Institute of Standards and Technology (NIST) is conducting market research to identify qualified vendors capable of supplying a Wirebond Pull Tester that meets specific technical requirements outlined in an attached Statement of Requirements. This sources sought notice is strictly for information gathering and is not a solicitation, request for quotation, or commitment to procure; no contracts will be awarded based on this announcement, and responders will not be compensated for their submissions. NIST is using this initiative to evaluate the market landscape, determine whether a small business set-aside is feasible, and assess eligibility of domestic manufacturers, with a particular emphasis on identifying products made in the United States. Responses must include the name of the supplier and manufacturer, the country of origin, technical specifications and product examples demonstrating compliance, typical lead times, and any additional relevant details—all within a four-page limit. Proprietary information may be marked, but sales brochures or marketing materials will be disregarded. The requirement is classified under NAICS code 334515 for instrument manufacturing related to electricity and electrical signals, with a small business size standard of 750 employees. All interested parties, regardless of size, are encouraged to respond, and the results will inform whether the subsequent procurement will be competitive or non-competitive, potentially conducted through SAM.gov. Submissions must be sent electronically to Lisa Stevens at [email hidden] no later than July 9, 2026, at 5:00 p.m. Eastern Time. Performance of the eventual contract, if awarded, is expected in Boulder, Colorado, while the contracting office is located in Gaithersburg, Maryland. The notice explicitly states no quotes will be accepted at this stage, and any future solicitation will be issued separately following analysis of the submitted information.

General Info

NIST seeks market info on U.S.-made Wirebond Pull Testers for potential future procurement, no contracts awarded.

Agency

Department Of Commerce Nist

Contract Value

$26,875

NAICS

334515 - Instrument Manufacturing for Measuring and Testing Electricity and Electrical Signals

Place of Performance

Boulder, CO, 80305, USA

Set-Aside

NONE

Awardee

K&R NEXT GENERATION BONDING INC.

Award Issued Date

08/19/2026, 12:00:00 AM UTC

Documents

Statement of Requirements for Wire-Pull Tester with Tweezer Attachment NB687000-26-02180

sow

High

AI Contract Breakdown

Uniform Contract Format

Timeline

PhaseAwarded

PostedJul 1

Sources Sought

AwardedAug 19

Contract was awarded

Submission Closed

07/09/2026, 05:00:00 PM UTC

Find active opportunities like this

Get full access to discover similar active contracts, track opportunities, and build proposals with AI assistance.

Organization & Contact Information

AgencyDepartment Of Commerce Nist

Contacts1 person available

OfficeGAITHERSBURG, MD, 20899, USA

Organization / AgencyDepartment Of Commerce Nist

Office AddressGAITHERSBURG, MD, 20899, USA

Contacts

Lisa Stevens

contact@example.gov

+1 (555) 000-0000

Full Description

National Institute of Standards and Technology (NIST)

Acquisition Management Division

Sources Sought for Commercial Product Purchase

THIS SOURCES SOUGHT IS NOT A REQUEST FOR QUOTATION.

It is a market research tool being used to determine potential and eligible business firms that can provide the product described herein prior to determining the method of acquisition.

The National Institute of Standards & Technology (NIST) seeks information on vendors that can provide Wirebond Pull Tester per the specifications attached herein.

This announcement is not a Request for Proposals or Quotes (RFP/RFQ) and does not commit the Government to award a contract now or in the future. The information contained in this notice is DRAFT only and, as such, is subject to change prior to the issuance of a solicitation. No solicitation is available currently. Additionally, the Government is not obligated to and will not pay for any information received from potential sources because of this Sources Sought announcement. The results of this Sources Sought will be utilized to determine if any Small Business Set-aside opportunities exist. All Small Business Set-aside categories will be considered. In addition, this market research tool is being used to identify potential and eligible firms, of all sizes, who manufacture the Wirebond Pull Tester in the U.S. prior to determining the method of acquisition and issuance of a solicitation. PLEASE INDICATE WHAT COUNTRY MANUFACTURES THIS PRODUCT.

After the results of this market research are obtained and analyzed, NIST may conduct a competitive or non-competitive procurement on the System for Award Management (sam.gov) and subsequently award a contract. If at least two qualified small businesses are identified during this market research stage that can fulfill the requirement, in accordance with the Specifications, then this acquisition shall be solicited as a small business set aside, however, NIST is seeking responses from ALL responsible sources, including large and small businesses. Responses should include the country where the product is manufactured.

This requirement is assigned a NAICS code of 334515, Instrument Manufacturing for Measuring and Testing Electricity and Electrical Signals, with a small business size standard of 750 employees.

Interested business organizations that believe they can meet the requirements should submit electronic copies of their capability statement. Please limit responses to four (4) pages or less. Responses should include the following information:

Name of the company that will provide the product(s).
Name of the company that will manufacture the product.
County of origin or manufacture of the product.
Spec/data sheets and examples of products that meet the specifications that demonstrate experience in meeting the requirements of this procurement.
Typical lead time to deliver the product after receipt of order
Any other relevant information that is not listed above that the Government should consider in developing its minimum specifications and finalizing its market research.

(Company sales brochures or marketing packages will not be considered.)

Any proprietary information should be so marked. The written capability statement should be received by the Contract Specialist, Lisa Stevens, via email at contact@example.gov no later than the date and time posted in this notice. No quotes will be accepted at this time and will not be considered.

REQUIREMENTS OVERVIEW:

See the attached Statement of Requirements document