STRAP, WEBBING

STRAP,WEBBING
STRAP, WEBBING
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RD002, COVERED DEFENSE INFORMATION APPLIES
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ003: CONFIGURATION CHANGE MANAGEMENT FOR EDGEWOOD FOR CHEMICAL,
BIOLOGICAL CENTER MATERIALS ENGINEERING CHANGE PROPOSAL REQUEST FOR
VARIANCE (DEVIATION OR WAIVER)
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
SPE7L1-27-T-0116
SECTION B
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
"SPECIFICATION CONTROL"
TDP Rev B Gen 4 IAW BASIC DRAWING NR 5B5M3 06A8176500 REVISION NR DTD 11/15/2018 PART PIECE NUMBER: 06A8176500
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176103 REVISION NR A DTD 09/22/2026 PART PIECE NUMBER: 06A8176500
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176100 REVISION NR DTD 11/15/2018 PART PIECE NUMBER: 06A8176500
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176101 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176102 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176202 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176302 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8178001 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8178002 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8178003 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176300 REVISION NR DTD 11/15/2018 PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176303 REVISION NR DTD 11/15/2018
SPE7L1-27-T-0116
SECTION B
PART PIECE NUMBER:
TDP Rev B Gen 4 IAW REFERENCE DRAWING NR 5B5M3 06A8176500 REVISION NR DTD 09/24/2026 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017529294 0001 EA 3.000
NSN/MATERIAL:5340016299561
DELIVERY (IN DAYS):0170
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z
UNIT CONT:ZZ
INTRMDTE CONT:ZZ INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PRESERVATION METHOD CODE 10: ITEMS MAY BE IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS
Packaging Requirements Sheet Commercial DS6421
PRON: -DSCP-FC-18-12096 REV ADATE: 08 JULY 2020
NSN: 5340-01-629-9561
Jennifer Vernon DSN 793-8133
The preservation, packing, and marking requirements for the item identified above shall be accomplished in accordance with the performance requirements defined herein. The following Packaging requirements shall apply:
SPE7L1-27-T-0116
SECTION B
PR: 7017529294 PRLI: 0001 CONT’D
PRESERVATION: COMMERCIAL
LEVEL OF PACKING: COMMERCIAL
QUANTITY PER UNIT PACKAGE:-001
1 Packaging. Preservation, packaging, packing, unitization and marking furnished by the supplier shall provide protection for a minimum of one year, provide for multiple handling, redistribution and shipment by any mode and meet or exceed the following requirements.
,,,,1.1 Cleanliness. Items shall be free of dirt and other contaminants which would contribute to the deterioration of the item or which would require cleaning by the customer prior to use. Coatings and preservatives applied to the item for protection are not considered contaminants. Cleaning may be any suitable process that is not injurious to the item or the protective finish.
,,,,1.2 Preservation. Items susceptible to corrosion or deterioration shall be provided protection by means of preservative coatings, volatile corrosion inhibitors, desiccants, waterproof and or watervaporproof barriers.
,,,,1.3 Cushioning. Items requiring protection from physical and mechanical damage (e.g. fragile, sensitive, material critical) or which could cause physical damage to other items shall be protected by wrapping, cushioning, pack compartmentalization, or other means to mitigate shock and vibration to prevent damage during handling and shipment. Items of a delicate nature shall not be subjected to damage from rugged items contained within the kit. Non-critical items of odd shapes or having sharp protrusions will not damage other items or protective barriers.
2 Unit Package. A unit package shall be so designed and constructed that it will contain the contents with no damage to the item(s), and with minimal damage to the unit pack during shipment and storage in the shipping container, and will allow subsequent handling. The outermost component of a unit package shall be a container such as a sealed bag, carton or box. Unit packs shall be designed to have minimum size and weight while retaining the protection required and enhancing standardization.
3 Unit Package Quantity. Unless otherwise specified, the unit package quantity shall be one each part, set, assembly, kit, etc.
4 Intermediate Package # (as applicable) Intermediate packaging is required whenever one or more of the following conditions exist: a.,,the quantity is over one (1) gross of the same national stock number <(>,<)> b.,,use enhances handling and inventorying<(>,<)> c.,,the exterior surfaces of the unit pack is a bag of any type, regardless of size<(>,<)> d.,,the unit pack is less than 64 cubic inches<(>,<)> e.,,the weight of the unit pack is less than five (5) pounds and no dimension is over twelve (12) inches. Intermediate containers shall be limited to a maximum of 100 unit packs, a net load of 40 pounds, or a maximum volume of 1.5 cubic feet, whichever occurs first.
5 Shipping Containers. Unit packages and intermediate packages not meeting the requirements for a shipping container shall be packed in shipping containers. All shipping containers shall be the most cost effective and shall be of minimum cube to contain and protect the items. The shipping container (including any necessary blocking, bracing, cushioning, or waterproofing) shall comply with the regulations of the carrier used and shall provide safe delivery to the destination at the lowest tariff cost. The shipping container shall be capable of multiple
SPE7L1-27-T-0116
SECTION B
PR: 7017529294 PRLI: 0001 CONT’D
handling, stacking at least ten feet high, and storage under favorable conditions (such as enclosed facilities) for a minimum of one year.
6 Unitization. Shipments of identical items going to the same destination shall be palletized if they have a total cubic displacement of 50 cubic feet or more unless skids or other forklift handling features are included on the containers. Pallet loads shall be stable, and to the greatest extent possible, provide a level top for ease of stacking. A palletized load shall be of a size to allow for placement of two pallet loads high and wide in a conveyance. The weight capacity of the pallet shall be adequate for the load. The preferred commercial expendable pallet is a 40 x 48 inch, 4-way entry pallet although variations may be permitted as dictated by the characteristics of the items being unitized. All variations must be approved by the contracting office prior to implementation. The load shall be contained in a manner that will permit safe handling during shipment and storage.
7 Marking. All unit packages, intermediate packs, exterior shipping containers, and, as applicable, unitized loads shall be marked in accordance with MIL-STD-129, including bar coding and a MSL label. The contractor is responsible for application of special markings as discussed in the Military Standard regardless of whether specified in the contract or not. Special markings include, but are not limited to, Shelf-life markings, structural markings, and transportation special handling markings. The marking of pilferable and sensitive materiel will not identify the nature of the materiel. Passive RFID tagging is required in all contracts that contain DFARS clause 252.211-7006. Contractors shall check the solicitation and/or contract for this clause. For details and most recent information, see http://www.acq.osd.mil/log/sci/ait.html http://www.acq.osd.mil/log/sci/ait.html for the current DoD Suppliers# Passive RFID Information Guide and Supplier Implementation Plan. If the item has Unique Item Identifier (UII) markings then the UII needs to be 2D bar coded and applied on the unit package, intermediate and exterior containers, and the unit load.
8 Hazardous Materials (as applicable): Hazardous Materials is defined as a substance, or waste which has been determined by the Secretary of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and which has been so designated. (This includes all items listed as hazardous in Titles 29, 40 and 49 CFR and other applicable modal regulations effective at the time of shipment.)
When applicable, the packaging and marking for hazardous material shall comply with the requirements for the mode of transport and the applicable performance packaging contained in the following documents: International Air Transport Association (IATA)# Dangerous Goods Regulations International Maritime Dangerous Goods Code (IMDG)# Code of Federal Regulations (CFR) Title 29, Title 40# and Title 49 Joint Service Regulation# AFJMAN24-204/TM38-250/NAVSUPPUB 505/MCO P4030.19/DLAM 4145.3 (for military air shipments).
If the shipment originates from outside the continental United States, the shipment shall be prepared in accordance with the United Nations Recommendations on the Transport of Dangerous Goods in a manner acceptable to the Competent Authority of the nation of origin and in accordance with regulations of all applicable carriers.
A Product Safety Data Sheet (SDS) is required to be included with every unit pack and intermediate container and shall be included with the packing list inside the sealed pouch attached to the outside of the package. ,, 9 Heat Treatment and Marking of Wood Packaging Materials. All non-manufactured wood used in packaging shall be heat treated to a core temperature of 56 degrees Celsius for a minimum of 30 minutes. The box/pallet manufacturer and the manufacturer of wood used as inner
SPE7L1-27-T-0116
SECTION B
PR: 7017529294 PRLI: 0001 CONT’D
packaging shall be affiliated with an inspection agency accredited by the board of review of the American Lumber Standard Committee. The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure tractability to the original source of heat treatment. Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens; on two sides of the pallet. Foreign manufacturers shall have the heat treatment of non-manufactured wood products verified in accordance with their National Plant Protection Organization#s compliance program. In addition, wood used as dunnage for blocking and bracing, to include ISO containers, shall be ordered with ALSC certified marking for dunnage or the markings may be applied locally at two foot intervals.
10 Quality Assurance. The contractor is responsible for establishing a quality system. Full consideration to examinations, inspections, and tests will be given to ensure the acceptability of the commercial package. All items, packing configurations, and markings supplied under this contract shall be identical to the first article
11 Supplemental NSN/Part Number: 5340-01-629-9561 Quantity: 3 EA Purchase Request: 7017529294QTY: 3 Delivery: 170 days ADO