This Solicitation opportunity from Department Of Defense was posted on May 18, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
STUD ASSEMBLY, TURNL
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract specifies the procurement of 1,035 packs of STUD ASSEMBLY, TURNLOCK FASTENER with NSN 5325-00-639-5055, supplied exclusively by HOWMET GLOBAL FASTENING SYSTEMS INC under part number 4002-15. This is a critical item with restricted sourcing, allowing no alternate offers, and requires origin inspection in accordance with specified quality standards. Technical and quality requirements are governed by the DLA Master List, with tailored higher-level contract quality provisions applying to both manufacturers and non-manufacturers. Inspection and acceptance occur at origin using zero-defect sampling per MIL-STD-1916 or ASQ H1331, with verification levels of VII, IV, and II for critical, major, and minor attributes respectively. Packaging must comply with MIL-STD-2073-1E and DLA packaging requirements, marked per MIL-STD-129 with no special marking codes, and palletized per RP001. Item Unique Identification is not required as per customer request. Delivery is FOB origin with no quantity variance allowed, due in 107 days by October 1, 2025, to DLA Distribution Warner Robins at Robins AFB, Georgia. The contract is issued under solicitation SPE4A6-26-T-48K2, classified under NAICS 332510, with primary point of contact Latoya Anderson.
General Info
Agency
NAICS
Place of Performance
BLDG 376, ROBINS A F B, GA, 31098-1887, USASet-Aside
Documents
(1)AI Contract Breakdown
Uniform Contract FormatWhat is UCF?
Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.
Timeline
Submission Closed
Organization & Contact Information
Full Description
STUD ASSEMBLY, TURNLOCK FASTENER
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
CRITICAL ITEM APPLICATION ORIGIN INSPECTION REQUIRED ACQUISITION OF THIS PART IS RESTRICTED TO THE SOURCE(S) SPECIFIED ON THE SOURCE CONTROL DRAWING. ALTERNATE OFFERS WILL NOT BE ACCEPTED. USE PROCUREMENT NOTE L22. THE TECHNICAL/QUALITY/TEST REQUIREMENTS FOR CITED P/N WILL BE IN CONFORMANCE WITH THE LISTED DRAWING.
SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SPE4A6-26-T-48K2
SECTION B
NOTE: U/I PG CONTAINS 10 STUD ASSEMBLIES
CRITICAL APPLICATION ITEM
HOWMET GLOBAL FASTENING SYSTEMS INC 71286 P/N 4002-15
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7011682165 0001 PG 1,035.000
NSN/MATERIAL:5325006395055
DELIVERY (IN DAYS):0107
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:31 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:BL OPI:M
INTRMDTE CONT:ED INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET
BLDG 376
ROBINS A F B GA 31098-1887
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET BLDG 376
SPE4A6-26-T-48K2
SECTION B
PR: 7011682165 PRLI: 0001 CONT’D
ROBINS A F B GA 31098-1887
US
Need Ship Date:00/00/0000 Original Required Delivery Date:10/01/2025
SPE4A6-26-T-48K2 NSN/Part Number: 5325-00-639-5055 Quantity: 1,035 PG Purchase Request: 7011682165QTY: 1035 Delivery: 107 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS