USCGC ACTIVE DRY DOCK (WMEC-618)

The United States Coast Guard Surface Forces Logistics Center intends to issue a Commercial Request for Quote (RFQ) for Dry Dock and repairs to the USCGC ACTIVE (618), 210 Foot "A Class" Medium Endurance Cutter. . The Coast Guard intends to conduct the procurement in accordance with Federal Acquisition Regulation (FAR) Part 12, Acquisition of Commercial Items, and FAR Subpart 13.5, Test Program for Certain Commercial Items. The simplified acquisition will be issued as a Best Value, Small Business Set-Aside, Request for Quote (RFQ), on or about July 22, 2011. The solicitation will be issued electronically via the Federal Business Opportunity web page at http://www.fbo.gov. It is incumbent upon contractors to monitor the FEDBIZOPS web page for the RFQ release and all subsequent amendments. Hard copies of the specification and solicitation will not be issued. The NAICS Code is 336611. The Geographical restriction is 300 Road Miles from the cutter's homeport of Port Angeles, WA All work will be performed at the contractor's facility. The performance period is schedule for Sixty-Two (62) calendar days and is expected to begin on or about November 29, 2011. The scope of the acquisition will include, but is not limited to: 1. Hull Plating (U/W Body), Ultrasonic Testing 2. Hull and Structural Plating - 3/16" Steel Plate, Repair 3. Appendages and Voids, Leak Test 4. Propulsion Shaft Fairwaters and Rope Guards, Inspect 5. Appendages and Voids - Internal, Preserve 6. Tanks (MP Fuel Service), Clean and Inspect 7. Voids (Non-Accessible), Leak Test 8. Voids (Non-Accessible), Preserve Internal Surfaces 9. Propulsion Shafting, Strain Gage Alignment Inspections 10. Propulsion Shafting; Remove, Inspect, and Reinstall (2 shafts) 11. Propulsion Shaft Coating, Renew (1 shaft) 12. Propulsion Shafting, Straighten (1 shaft) 13. Propulsion Shaft Seals, Overhaul (2 shafts) 14. Propeller Shaft Sleeves, Renew (2 shafts) 15. Propulsion Shaft Bearings (External), Renew (2 shafts) 16. Propulsion Stern Tube Bearings, Renew (2 stern tube) 17. Controllable Pitch propellers, Clean and Inspect (Port and Stbd) 18. CPP System, General Maintenance (Port and Stbd) 19. Controllable Pitch Propeller Hub Assembly, General Maintenance (Port and Stbd) 20. Fathometer Transducer, Renew 21. Doppler Speed Lo g Transducer, Renew 22. Sea Strainers (All Sizes), Overhaul or Renew 23. Rudder Assembly, Remove, Inspect and Reinstall (Port and Stbd) 24. Rudder Stock Bearings, check Clearances (Port and Stbd0 25. Anchors, anchor Chains and Ground Tackle, Inspect, Repair and Preserve 26. Grey Water Holding Tanks, Clean and Inspect 27. Sewage Holding Tanks, Clean and Inspect 28. Chain Lockers, Preserve 100% 29. Tanks (Grey Water Holding), Preserve "Partial" 30. Tanks (Sewage Holding), Preserve "Partial" 31. U/W Body, Preserve 100% 32. Stern Tube Interior Surfaces, Preserve 100% (Port and Stbd) 33. Main Master, Preserve 34. Cathodic Protection (Zincs) Renew 35. Drydocking 36. Temporary Services, Provide 37. Sea Valves and Waster Pieces, Overhaul or Renew 38. Vent Ducts (Engine Room, All), Commercial Cleaning 39. Vent Ducts (Galley and Pantry Room All), Commercial Cleaning 40. Vent Ducts (Laundry Exhaust and All Others), Commercial Cleaning 41. Rudder Stock, Rebuild (1 rudder stock) 42. Anchor Windlass, Level 2 Inspect and Repair (Port and Stbd) 43. Warping Capstan, Level 2 Inspect and Repair 44. Helo Talon Grid, Inspect and Test 45. Sea Trial Performance, Provide Support 46. 28 Volt DC Helo Power Supply, Load Test 47. Welin-Lambie Twin Pivot Arm Davit, Level 2 Inspect and Repair 48. Welin Lambie Davit Upgrade 49. Water Tight Bulkhead and Deck Steel, Renew 50. Machinery Space Bilge, Preserve 51. Bilge (Non-Machinery Space), Preserve 52. Chill and Heating Water Piping Insulation, Renew 53. Firemain Piping Insulation, Renew 54. Potable Water Piping Insulation, Renew 55. Steam Pipe Insulation, Renew 56. Ultrasonic Thickness Measurements, Steel Plate, perform 57. Exterior Comms Sys, HF Receive Long Wire Antenna, Renew 58. Bulwark Structural Repairs 59. Hull Preservation Interior, Machinery Spaces 60. Hull Preservation, Interior, Non-Machinery Spaces 61. Hull Insulation, Interior, Renew 62. Structural Longitudinal, Repair 63. Shipboard Davit Crane, Remove, Install and Weight Test 64. A-Class Single Point Davit Control Console, Upgrade A CD-ROM containing all applicable drawings will be sent via U.S. mail, if requested. Send all requests via e-mail to: contact@example.gov. The CD-ROM sets are available of all cutters and will be free of charge to contractors upon request. The CD-ROM(s) contain WINDOWS compliant raster/vector formats (e.g.*.DWF, etc). Trained welders who have been certified by the applicable regulatory code performance qualification procedures shall accomplish all welding and brazing. For further information or questions regarding this solicitation, please contact Arlene Woodley at +1 (555) 000-0000, or by email at contact@example.gov.