WASHER, FLAT
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
AI Contract Overview
The contract is for the procurement of three flat washers with NSN 5310-01-572-5729 under solicitation SPE4A0-26-T-4106, issued by the Department of Defense through the Aviation Supply Chain ESOC Buys office. The required delivery schedule is five days after award, and the submission deadline for responses is August 7, 2026. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, referenced by R and I numbers, with the controlling revision determined by the solicitation issue date for simplified acquisitions or the RFP issue date for larger acquisitions, unless amended. Physical identification and packaging must comply with RQ017 and RP001 standards, and non-accepted supplies must have government identification removed per RQ011. Sampling must follow MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required unless otherwise stated; attributes are to be classified as critical, major, or minor and assigned corresponding verification levels or AQLs of VII, IV, and II or 0.1, 1.0, and 4.0 respectively. Unspecified attributes are considered major. Manufacturer choice between attribute or variable inspection methods is permitted under MIL-STD-1916 unless the contract specifies otherwise. The place of performance is Fort Stewart, Georgia, and primary point of contact is Danita Davis, with email and phone provided for inquiries.
General Info
Agency
NAICS
Place of Performance
AWCF SSA, FORT STEWART, GA, 31314-0000, USSet-Aside
Documents
(0)AI Contract Breakdown
Uniform Contract FormatNo contract breakdown available.
Cannot generate Contract Breakdown because no documents were found from this contract's source.
Timeline
Response Deadline
Organization & Contact Information
Full Description
WASHER,FLAT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
ADEQUATE DATA FOR NSN/Part Number: 5310-01-572-5729 Quantity: 3 EA Purchase Request: 7017636757QTY: 3 Delivery: 5 days ADO
Similar Contracts
Same NAICS industry code
More opportunities from Department Of Defense → AVIATION SUPPLY CHAIN ESOC BUYS
Same awarding agency