This Solicitation opportunity from Department Of Defense was posted on August 5, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
WASHER, FLAT
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract is for the procurement of 70 flat washers (NSN 5310-01-562-2963, part number NAS1401-4C5G) under solicitation SPE4A6-26-T-13XK, issued by the Defense Logistics Agency’s ASC Commodities Division. Deliveries are required at Tinker AFB, Oklahoma, with a delivery deadline 104 days after award, and performance is governed by FOB Origin terms. Technical and quality requirements are defined by the DLA Master List of Technical and Quality Requirements, identified by R and I numbers including RA001, RP001, RQ011, and RQ017, which mandate compliance with specific packaging, marking, and removal of government identification protocols. Packaging must adhere to ASTM D3951 and DLA’s RP001 standards, while labeling and barcoding must follow MIL-STD-129, including hazard communication per OSHA 29 CFR 1910.1200 for non-exempt materials. Hazardous and radioactive materials require prior label submissions and advance notifications, with strict adherence to MIL-STD-129 for container marking. Inspection and acceptance occur at destination, with quality verification governed by MIL-STD-1916 or ASQ H1331, Table 1, employing zero-defect acceptance unless otherwise specified, with critical, major, and minor attributes assigned verification levels VII, IV, and II respectively. Export-controlled technical data subject to ITAR or EAR is involved, restricting dissemination to only those contractors possessing approved JCP certification, having completed required DLA export training, and been authorized by DLA. Cybersecurity obligations under DFARS 252.204-7012 and NIST SP 800-171 are mandatory, aligning with CMMC Level 2 requirements and safeguarding covered defense information. Offers must be submitted electronically through DIBBS by August 13, 2026, with price evaluation preferences for HUBZone small businesses applied, and the award is expected to follow a Lowest Price Technically Acceptable methodology given the absence of trade-off language and presence of technical thresholds. Payment must be processed via WAWF, and all offerors must provide valid UEI and CAGE codes, represent size and socioeconomic status accurately, and comply with all representations and
General Info
Agency
NAICS
Place of Performance
3301 F AVE CEN REC BLDG 506 DR 22, TINKER AFB, OK, 73145-8000, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
WASHER, FLAT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 5310-01-562-2963 Quantity: 70 EA Purchase Request: 7017612374QTY: 70 Delivery: 104 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS