Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, October 28 at 2:00 PM ET

Register Free →

This Solicitation opportunity from Department Of Defense was posted on July 13, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.

WASHER, LOCK

Closed
SPE4A6-26-T-05SZFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

Active Opportunities Like This One

AI Contract Overview

Show more

The contract requires the delivery of two units of a lock washer, identified by NSN 5310-01-515-5043, within 90 calendar days from the contract date for first article testing at the Fleet Readiness Center East in Cherry Point, North Carolina. The government will evaluate these units and provide written notification of approval, conditional approval, or disapproval within 30 days of receipt. Approval is mandatory before any further production can proceed, and the first article units must be retained by the contractor as a manufacturing standard until all quantities under the contract are produced and accepted. In indefinite delivery cases, the units must be retained until the final production run is approved. The contractor must comply with DFARS 252.245-7004(d) for proper disposition of the first articles and is required to provide details of current dealer or distributor certification and accreditation, as equivalent alternatives are not accepted without substantiation. Fast pay terms do not apply to this solicitation. The contract, issued under solicitation SPE4A6-26-T-05SZ by the Department of Defense, has a response deadline of July 21, 2026, with a total procurement quantity of 21 units and a delivery schedule of 391 days after award. The place of performance is listed as Tracy, California, with Bernice Adams as the primary point of contact.

General Info

Deliver two lock washers for first article testing; approval required before production; retain units as standard.

NAICS

332722 - Bolt, Nut, Screw, Rivet, and Washer Manufacturing

Place of Performance

REC WHSE 57, TRACY, CA, 95304-5000, USA

Set-Aside

NONE

Documents

1

RFQ SPE4A6-26-T-05SZ Request for Quotations DLA Aviation

PDF, High priority: read this firstrfq
High

AI Contract Breakdown

Uniform Contract Format

Sign up to view the full breakdown with detailed analysis of each section.

Timeline

2 updates
PhaseClosed
Posted

Solicitation

Notice updated

The notice title changed. The notice description changed.

Notice updated

The notice title changed. The notice description changed.

Response Deadline

Deadline has passed

Submission Closed

Find active opportunities like this

Start your free trial to discover similar active contracts, track opportunities, and build proposals with AI assistance.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC COMMODITIES DIVISION
Contacts1 person available
OfficeUSA
Office AddressUSA
Contacts
BERNICE ADAMS

Full Description

Show more
OF THE SOLICITATION, SELECT
‘OTHER EQUIVALENT' AND PROVIDE DETAILS OF CURRENT DEALER/DISTRIBUTOR
CERTIFICATION AND/OR ACCREDITATION.
Fast Pay does not apply to this solicitation
FIRST ARTICLE APPROVAL – GOVERNMENT TESTING REQUIRED (FAR 52.209-4 AND
ALT I)
THE CONTRACTOR SHALL DELIVER 2 UNIT(S) OF
LOT/ITEM 5310 / 15155043
WITHIN 90 CALENDAR DAYS FROM THE DATE OF
THIS CONTRACT TO THE GOVERNMENT AT THE LOCATION SPECIFIED BELOW FOR
FIRST ARTICLE TESTS.
N65923
FLEET READINESS CENTER EAST
RECEIVING OFFICER
BLDG 148, BAY C
BEACHEY ROAD
CHERRY POINT
NC
28533-5040
WITHIN 30 CALENDAR DAYS AFTER THE GOVERNMENT
RECEIVES THE FIRST ARTICLE, THE CONTRACTING OFFICER SHALL NOTIFY THE
CONTRACTOR, IN WRITING, OF THE CONDITIONAL APPROVAL, APPROVAL, OR
DISAPPROVAL OF THE FIRST ARTICLE.
DISPOSITION OF FIRST ARTICLES:
Procurement Note E01: Supplemental First Article Exhibit Disposition Contractor Maintained (MAY 2020)
The first article units will be maintained or returned to the contractor to be used as a manufacturing standard. The contractor shall hold the approved first article units at the production facility until all production quantities have been produced and accepted. In the case of indefinite delivery contracts, the contractor shall hold the first article units until final production run has been approved and accepted on the first delivery order. The unit shall be considered a production guide or manufacturing standard if defects are reported on delivered material or problems are encountered during production. When disposing the units, the contractor shall follow DFARS 252.245-7004(d).
Procurement Note M04: NSN/Part Number: 5310-01-515-5043 Quantity: 21 EA Purchase Request: 7017271966QTY: 21 Delivery: 391 days ADO

More opportunities from Department Of Defense → ASC COMMODITIES DIVISION

Same awarding agency

NAICS: 332722
New
DIBBS
WASHER, LOCK
Solicitation # SPE4A6-26-T-40D5
Solicitation SPE4A6-26-T-40D5 is a fixed-price procurement issued by the Defense Logistics Agency for 91 internal and external tooth lock washers, identified by NSN 5310012533723. The required components must be manufactured from Stainless Steel CRES 302 and adhere to technical specifications FF-W-100 Type 3 Style 1 and FF-W-100C(1). Dimensional requirements are governed by MS 45904-86 or ASME B18.21.1, with specific tolerances for the inner diameter (.512 to .530 inches), outer diameter (1.380 to 1.410 inches), and thickness (.052 to .060 inches). The items are to be delivered to the DLA Distribution DDSP New Cumberland facility in Pennsylvania by November 27, 2026, with a delivery window of 202 days after order. Quality assurance and inspection will occur at the point of origin, requiring compliance with MIL-STD-1916, ASQ H1331, or MIL-STD-105/ASQ Z1.4, with a zero-nonconformance acceptance policy. Packaging must follow RP001 and ASTM D3951, while marking and labeling must comply with MIL-STD-129 and MIL-STD-130N. Item Unique Identification is not required. The contract incorporates various FAR and DFARS clauses, including the Buy American Act and safeguarding requirements for covered defense information under NIST SP 800-171. Payment processing is mandated through the Wide Area Workflow system. This is not a small business set-aside, and it falls under NAICS code 332722.
Bolt, Nut, Screw, Rivet, and Washer Manufacturing

POSTED

4 days ago

DEADLINE

in about 14 hours
View Details

Earlier notices in this NAICS code

Posted before this notice, open and closed

Find Active Opportunities Like This

Get AI-powered intelligence on the opportunities still open

Every page of the solicitation package shredded into a compliance breakdown

AI-powered matching based on your capabilities and past performance

Competitor and incumbent history on the requirement

Automated alerts on amendments, Q&A deadlines, and award

Miguel
Hillary
Keith Deutsch
Christine

Join 750+ contractors already using CLEATUS