WEAPON RAIL ADAPTER

16100 EA. W/100% OPTION NSN# 1005-01-452-3527 WEAPON RAIL ADAPTER SOL OPEN/CLOSE: 05/29/13 - 06/28/13 ********************************************************************** ITEM DESCRIPTION FOR PR: 0048747322 ADAPTER RAIL, WPN MOUNTED, M4 _______________EXCEPTION DATA____________________ MIL-DTL-16232, para 6.2.1- DD FORM 1423 is replaced by SUPPLEMENTAL QUALITY ASSURANCE PROVISION (SQAP) PHOS-DL-MANG IF DRAWING NOTE GIVES OPTION FOR ZINC OR MANGANESE COATING THEN MANGANESE IS REQUIRED. SUPPLEMENTAL QUALITY ASSURANCE PROVISION (SQAP) PHOS-DL-MANG, PARAGRAPH 3: REPLACE, "ADDITIONAL '30' DAYS WILL BE REQUIRED FOR REVIEW/APPROVAL DETERMINATION", WITH "ADDITIONAL '45' DAYS WILL BE REQUIRED FOR REVIEW/ APPROVAL DETERMINATION. CORRECT DATE OF REVISION FOR DWG 12973131, REV B, IS 10/17/2007. ______________END OF EXCEPTIONS__________________ __________SPECIAL PACKAGING INSTRUCTIONS_________ SEE PD 12973095 AND NOR L07S3110-12973095 ______END OF SPECIAL PACKAGING INSTRUCTIONS______ THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799). ANY MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF STATE. DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC) REGISTRATION WHEN REQUESTED WILL RESULT IN WITHDRAWAL OF QUOTES/OFFERS. THE ITEM BEING PROCURED IS A CRITICAL GUN PART ITEM WITH UNIQUE REQUIREMENTS. CONTRACTOR FAT APPLIES. PER FAR 52.209-3: (a) THE CONTRACTOR SHALL TEST 5 UNIT(S)... AT LEAST 10 CALENDAR DAYS BEFORE THE BEGINNING OF FIRST ARTICLE TESTING, THE CONTRACTOR SHALL NOTIFY... (b) THE CONTRACTOR SHALL SUBMIT THE FAT REPORT WITHIN 120 CALENDAR DAYS... (NOTE: THE DELIVERY SCHEDULE ON THE FACE OF THE SOLICITATION REFLECTS ONLY THE TIME TO DELIVER THE SUPPLIES.) WITHIN 45 CALENDAR DAYS AFTER THE GOVERNMENT RECEIVES THE FIRST ARTICLE THE CONTRACTING OFFICER SHALL NOTIFY... PER DLAD 52.209-9017, ALT III DISPOSITION OF FIRST ARTICLES: AFTER RECEIPT OF QUOTES, OFFERORS MAY BE CONTACTED TO PRICE THE FAT REQUIREMENT. SEE FAR 52.209-3 (e), THE CONTRACTOR MAY DELIVER THE APPROVED FIRST ARTICLE AS PART OF THE CONTRACT QUANTITY... PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE TO THIS CONTRACT WILL BE APPROVED BY THE CONTRACT POST AWARD CONTRACTING OFFICER (PCO). POST AWARD PREPRODUCTION APPROVAL VERIFYING THE REQUIREMENTS OF MIL-DTL-16232 IS REQUIRED. A CONTRACT DATA REQUIREMENTS LIST (CDRL), IDENTIFIED IN A SQAP AS A PHOS-DL-MANG AND A SUGGESTED OUTLINE, IDENTIFIED IN A SQAP AS PHOS- OUTLINE-16232, PROVIDE THE PHOSPHATE COATING PROCEDURE REQUIREMENTS/FORMAT AND ARE INCLUDED IN THE TECHNICAL DATA PACKAGE. THE CONTRACTOR MUST PROVIDE COPIES OF PHOSPHATE COATING PROCEDURES WRITTEN SPECIFICALLY FOR THE COATING OF PARTS ON THIS CONTRACT TO THE PCO WITHIN 45 DAY AFTER AWARD. AN ADDITIONAL 45 DAYS WILL BE REQUIRED FOR REVIEW/APPROVAL DETERMINATION. PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA QAR AT THE ACTUAL MANUFACTURER'S FACILITY AND IN PROCESS INSPECTIONS WILL OCCUR AT THE PHOSPHATE CONTRACTOR'S FACILITY IDENTIFIED ON THIS CONTRACT. THE IDENTIFICATION OF THE ACTUAL MANUFACTURER AND PHOSPHATE CONTRACTOR MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST BE APPROVED BY THE PCO VIA FORMAL CONTRACT MODIFICATION. A WAIVER FOR THE PHOSPHATE PREPRODUCTION REQUIREMENTS OF MIL-DTL-16232 PARAGRAPH 3.1 CAN BE SUBMITTED. THE DOCUMENTATION REQUIRED FOR EVALUATION OF THIS WAIVER REQUEST MUST INCLUDE: A PHOSPHATE PROCEDURE THAT HAS BEEN REVIEWED AND APPROVED BY THIS PROCURING AGENCY AND A TEST REPORT (GOVERNMENT FIRST ARTICLE OR PRODUCTION VERIFICATION TEST)FROM WITHIN THE LAST YEAR IN WHICH THE PHOSPHATE COATING WAS TESTED AND PASSED (FOR ANY NSN). THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST MEET QPL/QML SPECIFICATIONS AS IDENTIFIED IN THE TECHNICAL DATA PACKAGE. CLAUSE I09A01 (FAR CLAUSE 52.209-1) QUALIFICATION REQUIREMENTS IS APPLICABLE. THE AWARDEE SHALL PROVIDE QPL/QML COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/QML(S). THE IDENTIFICATION OF ALL APPLICABLE QPL/QML SOURCES MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR EVALUATION PRIOR TO CONTRACT AWARD. PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD 52.246-9004 MAY BE INVOKED FOR THE REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING TESTING. PRODUCT VERIFICATION TESTING, IF INVOKED, WILL BE PERFORMED PRIOR TO ACCEPTANCE OF EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE PVT SAMPLES FROM EACH SUBCONTRACTOR AND FROM EACH PHOSPHATE CONTRACTOR USED IN THE PRODUCTION OF PARTS ON THIS CONTRACT. FIVE (5) PVT SAMPLES WILL BE REQUIRED TO BE IDENTIFIED TO THOSE SUBCONTRACTORS AND PHOSPHATE CONTRACTORS WHEN THEY ARE SENT IN FOR TESTING. CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED. FAR CLAUSE 52.246-11 APPLIES A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008 OR THE FOLLOWING TAILORED VERSION OF ISO 9001:2008 IS REQUIRED OR A PROGRAM EQUIVALENT TO THE TAILORED VERSION OF THE ISO 9001:2008 IS REQUIRED. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.2.1 General, Documentation Requirements [b and d only] 4.2.2 Quality manual 4.2.3 Control of documents 4.2.4 Control of records 6.2.2 Competence, training and awareness 6.4 Work environment (if applicable) 7.1 Planning of product realization 7.2.1 Determination of requirements related to the product 7.2.2 Review of the requirements related to product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchase Product 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property (if applicable) 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1a General for Measurement, Analysis and Improvement 8.2.2 Internal Audit 8.3 Control of nonconforming product 8.2.4 Monitoring and measurement of product 8.5.2 Corrective action 8.5.3 Preventive action CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT, APPLIES. THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATILE CREEK, MI 49017-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25." "THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST CONFORM TO SOURCE CONTROL DRAWING. BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE SOURCE CONTROLLED COMPONENTS FROM SOURCES APPROVED ON THE APPLICABLE SOURCE CONTROL DRAWING." MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D). A KNIGHTS ARMAMENT COMPANY TECHNICAL DATA PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE CONDITIONS APPLY AND VENDORS MUST COMPLETE AND RETURN THE APPLICABLE KNIGHTS ARMAMENT COMPANY CERTIFICATION FORMS WHICH ARE LOCATED IN THE DLA CFOLDERS APPLICATION: https://pcf1.bsm.dla.mil/cFolders DLAD PROVISION 52.211-9009 IS APPLICABLE TO THIS SOLICITATION, THEREFORE SURPLUS MATERIAL WILL NOT BE CONSIDERED. IF PRESENT IN THE SOLICITATION, PROVISION 52.211-9003 AND CLAUSE 52.211-9000 ARE NOT APPLICABLE. CRITICAL APPLICATION ITEM I/A/W QAP 16236 PHOS-DL-MANG REFNO DTD 11/05/10 AMEND NR DTD 11/05/10 TYPE NUMBER I/A/W QAP 16236 PHOS-OUTLINE-16232 REFNO DTD 10/20/10 AMEND NR A DTD 10/15/10 TYPE NUMBER I/A/W QAP 16236 PHOS-OUTLINE-DRY REFNO DTD 10/20/10 AMEND NR A DTD 10/15/10 TYPE NUMBER I/A/W QAP 16236 PHOS-QAR-CHECK REFNO DTD 10/20/10 AMEND NR A DTD 10/15/10 TYPE NUMBER I/A/W DRAWING NR 19200 12579607 REFNO DTD 09/14/10 AMEND NR C DTD 08/04/09 TYPE NUMBER I/A/W DRAWING NR 19200 12972653 REFNO DTD 01/12/12 AMEND NR D DTD 09/28/11 TYPE NUMBER I/A/W DRAWING NR 19200 12973027 REFNO DTD 02/04/11 AMEND NR A DTD 04/10/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973033 REFNO DTD 06/28/12 AMEND NR D DTD 09/08/11 TYPE NUMBER I/A/W DRAWING NR 19200 12973095 REFNO DTD 07/19/12 AMEND NR DTD 06/29/12 TYPE NUMBER I/A/W DRAWING NR 19200 12973095 BASIC DTD 02/04/11 AMEND NR E DTD 11/21/06 TYPE NUMBER I/A/W SPEC NR 19200 12973095 REFNO DTD 07/19/12 AMEND NR E DTD 11/21/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973095 REFNO DTD 01/11/13 AMEND NR B DTD 03/28/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973096 REFNO DTD 02/04/11 AMEND NR D DTD 05/04/09 TYPE NUMBER I/A/W DRAWING NR 19200 12973097 REFNO DTD 06/29/12 AMEND NR H DTD 09/12/11 TYPE NUMBER I/A/W DRAWING NR 19200 12973099 REFNO DTD 02/04/11 AMEND NR C DTD 04/10/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973100 REFNO DTD 06/28/12 AMEND NR H DTD 09/12/11 TYPE NUMBER I/A/W DRAWING NR 19200 12973101 REFNO DTD 02/04/11 AMEND NR B DTD 09/20/10 TYPE NUMBER I/A/W DRAWING NR 19200 12973102 REFNO DTD 12/14/10 AMEND NR C DTD 03/06/08 TYPE NUMBER I/A/W DRAWING NR 19200 12973103 REFNO DTD 12/14/10 AMEND NR B DTD 12/20/07 TYPE NUMBER I/A/W DRAWING NR 19200 12973104 REFNO DTD 12/14/10 AMEND NR B DTD 03/06/08 TYPE NUMBER I/A/W DRAWING NR 19200 12973105 REFNO DTD 12/14/10 AMEND NR B DTD 12/20/07 TYPE NUMBER I/A/W DRAWING NR 19200 12973131 REFNO DTD 12/21/10 AMEND NR B DTD 04/10/07 TYPE NUMBER I/A/W DRAWING NR 19200 12973132 REFNO DTD 12/21/10 AMEND NR B DTD 04/10/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973133 REFNO DTD 12/21/10 AMEND NR B DTD 04/10/06 TYPE NUMBER I/A/W DRAWING NR 19200 12973135 REFNO DTD 02/07/11 AMEND NR B DTD 04/10/06 TYPE NUMBER I/A/W DRAWING NR 19200 12993884 REFNO DTD 10/10/12 AMEND NR F DTD 08/15/12 TYPE NUMBER I/A/W DRAWING NR 19200 13011435 REFNO DTD 10/22/10 AMEND NR A DTD 02/07/08 TYPE NUMBER I/A/W DRAWING NR 19200 13012014 REFNO DTD 10/22/10 AMEND NR B DTD 10/17/07 TYPE NUMBER I/A/W DRAWING NR 19200 13012015 REFNO DTD 10/22/10 AMEND NR B DTD 01/10/08 TYPE NUMBER I/A/W DRAWING NR 19200 13012016 REFNO DTD 02/07/11 AMEND NR C DTD 02/07/08 TYPE NUMBER I/A/W DRAWING NR 19200 13012018 REFNO DTD 02/07/11 AMEND NR B DTD 02/07/08 TYPE NUMBER I/A/W DRAWING NR 19200 L07S3110 REFNO DTD 07/19/12 AMEND NR B DTD 10/16/07 TYPE NUMBER I/A/W DRAWING NR 19200 L07S3110-12973095 REFNO DTD 02/07/11 AMEND NR B DTD 10/31/07 TYPE NUMBER I/A/W DRAWING NR 19200 L12S3161 REFNO DTD 02/07/13 AMEND NR DTD 01/08/13 TYPE NUMBER I/A/W DRAWING NR 19200 L2S3025 REFNO DTD 09/01/10 AMEND NR E DTD 05/03/02 TYPE NUMBER I/A/W SPEC NR DI-NDTI-80809B REFNO DTD 10/03/06 AMEND NR B DTD 10/03/06 TYPE NUMBER I/A/W SPEC NR MIL-A-8625F(1) REFNO DTD 10/02/06 AMEND NR 1 DTD 10/02/06 TYPE NUMBER I/A/W SPEC NR MIL-DTL-13924D NOT 1 REFNO DTD 10/02/06 AMEND NR D DTD 10/02/06 TYPE NUMBER I/A/W SPEC NR MIL-DTL-16232G NOT 1 REFNO DTD 10/03/06 AMEND NR G DTD 03/14/13 TYPE NUMBER I/A/W SPEC NR QPL-16173-84 NOT 1 REFNO DTD 10/03/06 AMEND NR 84 DTD 10/03/06 TYPE NUMBER I/A/W SPEC NR QPL-3150-34 NOT 1 REFNO DTD 10/03/06 AMEND NR 34 DTD 10/03/06 TYPE NUMBER I/A/W SPEC NR QPL-46010-18 NOT 1 REFNO DTD 10/03/06 AMEND NR 18 DTD 10/03/06 TYPE NUMBER