ROLLER, BEARING

ROLLER,BEARING
ROLLER, BEARING
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
RT001: MEASURING AND TEST EQUIPMENT
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THE TECHNICAL/QUALITY/TEST REQUIREMENTS FOR
CITED P/N WILL BE IN CONFORMANCE WITH
THE LISTED DRAWING.
** BEARING RESTRICTIONS
RESTRICTION ON THE ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011)
AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING
MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR
EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (ROLLING
ELEMENTS, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE
SPE4A6-27-T-7794
SECTION B
UNITED STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE
TOTAL COST OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE
DFARS CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER
BEARINGS.
A CONTRACTOR’S DECLARATION ON THE DOMESTIC/FOREIGN NATURE OF MATERIAL
BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN BEARING WEBSITE AT
https://www.dla.mil/Aviation/Business/Foreign-Bearing-Waiver/. TO OBTAIN A COPY OF THE CONTRACTOR’S DECLARATION. PLEASE PRINT, COMPLETE, SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING CONSIDERD FOR AWARD.
IN THE EVENT NO OFFERED BEARINGS MEET THIS SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED OR HELD PENDING A WAIVER APPROVAL REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT MAY BE RE-SOLICITED OR BUYER MAY REQUEST A QUOTE EXTENSION. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL AND ROLLER BEARINGS.
SOURCE CONTROL ITEM RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
US ARMY TANK COMMAND CAGE 19207 ; SOURCE CONTROL DRAWING #11628807.
** DRAWING EXCEPTIONS (6-items) Updated to Commercial Specifications #1)Old ASME Y14.34M replaced by ASME Y13.34; #2) Old ASME-Y14.100 remove dash to ASME Y14.100; #3) Old ASME-14.24 remove dash to AMSE Y14/34; #4) Old ASME-Y14.34M replaced by ASME Y14.34; #5) Old ASME-Y14.35M remove dash to ASME Y14.35M; and #6) Old MIL-STD-100 replaced by ASME Y14.100 AND ASME Y14.24 AND ASME Y14.35M AND ASME 14.34M).
APPROVED SOURCE:
CAGE 5XMS1 ( JTEKT NORTH AMERICA AKA KOYO BEARINGS).
CRITICAL APPLICATION ITEM
JTEKT BEARINGS NORTH AMERICA LLC 5XMS1 P/N 11628807
TDP Rev B Gen 3 IAW BASIC DRAWING NR 19207 11628807 REVISION NR C DTD 12/01/1981 PART PIECE NUMBER:
TDP Rev B Gen 3 IAW REFERENCE DRAWING NR 19207 11628807 REVISION NR 09 DTD 09/11/2026 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018679169 0001 EA 417.000
NSN/MATERIAL:3110011095867
SPE4A6-27-T-7794
SECTION B
PR: 7018679169 PRLI: 0001 CONT’D
DELIVERY (IN DAYS):0147
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:BS OPI:M
INTRMDTE CONT:ED INTRMDTE CONT QTY:100
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3210
DLA DISTRIBUTION DEPOT HILL
7537 WARDLEIGH RD
HILL AFB UT 84056-5734
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3210
DLA DISTRIBUTION DEPOT HILL
DDHU CML +1 (555) 000-0000
7537 WARDLEIGH RD BLDG 849W
HILL AFB UT 84056-5734
US
Need Ship Date:04/06/2027 Original Required Delivery Date:11/12/2027
SPE4A6-27-T-7794 NSN/Part Number: 3110-01-109-5867 Quantity: 417 EA Purchase Request: 7018679169QTY: 417 Delivery: 147 days ADO