Request for quote. Please state your price, your very best delivery and the country of origin. Please respond by email to
contact@example.gov. These orders are for the GSA warehouse and all clauses that normally apply to our warehouse orders are applicable, including bar code marking and the Buy American Act which can be found at Federal Acquisition Regulations 25.001.Procurement History PRC Desoto $105.46 5130-00-924-6396 UI: EA QTY 16 GUN, SEALANT: DESCRIPTION Pneumatic powered sealant gun less air hose assembly. The sealant gun shall consist of a valve assembly, bracket assembly, handle assembly and 6 fluid ounce retainer. The handle assembly shall be capable of removal to facilitate application in confined areas and the bracket assembly shall function with the handle assembly removed. The bracket assembly shall have a swivel with a 5/16-24 NF-2A thread. The swivel shall be part of the valve assembly attached to a bracket unit to make up the bracket assembly. The valve assembly, when actuated by a control lever, shall vary air volume from zero to full volume at constant pressure. The handle assembly shall consist of a pistol grip type handle and a conveniently located trigger type throttle which shall actuate the valve assembly through the bracket assembly control lever when the handle and bracket assemblies are combined. The bracket assembly shall accept cartridge retainers in 2-1/2, 6, and 12 fluid ounce sizes manufactured by Semco Division of Courtaulds Aerospace. The operation range shall be 0 - 100 psig minimum. Capable of operation in a 4" hole. Measures 8" long. Furnished with operating and maintenance instructions, parts list, accessory list, and manufacturer's standard equipment. PRC-Desoto International Part Number 250065 or equal Offering on: Manufacturer's Name: __________________________Brand___________________________________ Model or Part No. __________________________________ ITEM MARKING Mark each item in a permanent and legible manner with manufacturer's part number and name or identifying symbol. PACKAGING One (1) item shall be preserved and packaged in a unit package designed to protect the item against damage during shipment, handling, and storage. PACKING The unit packages shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Classification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200, or ECT 32. MARKING All unit, intermediate, transport packages and unit loads shall be marked and bar coded for delivery to civilian activities in accordance with FED-STD-123G, dated June 6, 1997, or marked and bar coded for delivery to military activities in accordance with MIL-STD-129P, change 2, dated 10 February 2004, as applicable. Palletization: The shipping (transport) containers shall be palletized. The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, and double-face non-reversible pallets. The palletized load shall not exceed 2500 pounds in weight for shipments to the Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (French Camp Location). The palletized load shall not overhang the pallet deck board edge by more than 1 inch and shall not exceed 53 inches in overall height (including pallet). Less than half pallet loads or loads shipped by small package carrier in acceptable transport packing need not be palletized. When less than full but more than a half pallet is used, the palletized load shall utilize proper bracing and/or reinforcement to ensure that the load can withstand two additional loads placed on it. Stacking: A load-stacking test shall be performed once, at the beginning of the contract, for each different unitized or palletized load configuration. A fully palletized load shall be tested utilizing a total stack of three palletized loads, with all the proper bracing and/or reinforcement necessary to perform the test. There shall be no evidence of damage to the pallets, shipping containers or products when stack is tested on the rigid surface for a minimum of 24 hours, in compliance with all the National and Local Safety Regulations. The pre-tested palletized load configuration shall be duplicated using the same packaging materials, pattern, number of shipping (transport) containers, and procedures consistent throughout the duration of the contract. Palletized loads shall be stable and safe when handled with mechanical equipment by qualified personnel. Materials: All lumber used inside or outside a shipment shall be bark free. No used wood pallets with repaired components or stringers will be acceptable. All wood pallet stringers shall be manufactured from hardwoods. Pallets manufactured of materials other than wood, shall conform to all the requirements specified herein. Unitization: For the purpose of this requirement, the assembled group of containers or items in a single load that can be handled as a unit throughout the distribution system. Unitization encompasses, but is not limited to, consolidation in a container, placement on a pallet or load base having forklift capability, or securely binding together. Shipments should be considered for unitization where appropriate or specified. Unitization of pallet load: The palletized load shall be unitized and secured to the pallet to insure that the load arrives intact without product damage. The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Vertical, horizontal or filler reinforcement shall be added as necessary to meet the stacking strength requirements. A palletized load shall be secured to the pallet by shrink or stretch wrapping, and/or, by steel or nonmetallic strapping. When steel or nonmetallic strapping is used, edge protectors shall be provided to prevent damage to the cartons when tensioning the strapping. As a minimum, two straps shall run lengthwise, two straps shall run widthwise, and two straps shall run around the girth of the palletized load. A palletized load shall be capable of protecting the products against damage in a multiple handling, transportation, and storage environment having distribution warehouses with rack systems that support the load/s overhead of warehouse personnel. Notice of special requirements for shipment to European Union countries: Per Clause D-FSS-468, non-manufactured wood pallets and other non-manufactured wood package material used in shipments destined for ultimate delivery to or through a European Union (EU) country shall comply with the Emergency Measures (2001/219/EC) adopted by the Commission of the European Communities (CEC). Additionally, shipments delivered to DoD distribution facilities or freight consolidation points for eventual delivery to or through EU countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17. BIDDERS OFFERING OTHER THAN BRAND NAME ITEMS IDENTIFIED HEREIN MUST FURNISH WITH THEIR BIDS ADEQUATE DESCRIPTIVE LITERATURE SO THAT A DETERMINATION CAN BE MADE AS TO EQUALITY OF THE PRODUCTS OFFERED. IN ORDER FOR THE GOVERNMENT TO MAKE AN "OR EQUAL" DETERMINATION OF THE OFFERED PRODUCT(S), THE FURNISHED INFORMATION MUST DELINEATE EACH APPLICABLE CHARACTERISTIC, UNIT OF MEASURE, AND TEST METHOD OF THE OFFERED PRODUCT(S) DIRECTLY CORRELATED TO EACH OF THE REQUIREMENTS DELINEATED IN THE ITEM PURCHASE DESCRIPTION. FAILURE TO FURNISH THIS INFORMATION/LITERATURE WILL RESULT IN THE BID BEING REJECTED AS NON-RESPONSIVE OR MAY BE CONSIDERED AS UNACCEPTABLE FOR AWARD IN A NEGOTIATED PROCUREMENT (SEE GSAR CLAUSE 552.211-70).
