5120-01-398-0398

See attached limited source justification. 5120-01-398-0398 UI: EA SPANNER ATTACHMENT, SOCKET WRENCH: DESCRIPTION Type: Spanner Attachment, Socket Wrench End Item Identification: NSN 1520-01-106-9519, Attack Helicopter Drive Surface Size: 0.375 Inches Single End Drive End Shape: Square Single End Internal Special Features: Two 0.365 In. Max Dia Pins; 1.415 In. C To C Distance Between Pins Functional Description: Used To Install/Remove Anti-Flail Bearing Nut Material: Steel Overall Surface Treatment: Passivate Overall Enginetics Corporation Part Number: 140069 ITEM MARKING Each item Shall Be Marked in a Permanent and Legible Manner with: 1) Manufacturer's Part Number 2) Manufacturer's Name or Identifying Symbol, and 3) Country of Origin Each Package including the unit, single, intermediate, and exterior container must be labeled with the requisition number or Transportation Control Number (TCN). Requisition Number and TCN are found on the Purchase Order. PACKAGING Shall be in accordance with the latest Edition of ASTM D 3951-98, "Practice for Commercial Packaging" available at www.ASTM.org. PACKING The unit packages shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Classification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200 psi, or Edge Crush Test (ECT) 32 Lbs. per Inch Width. MARKING All unit, intermediate, transport packages and unit loads shall be marked and bar coded for delivery to civilian activities in accordance with the latest version of FED-STD-123, "Marking For Shipment (Civil Agencies)", or marked and bar coded for delivery to military activities in accordance with the latest version of MIL-STD-129, "Military Marking For Shipment and Storage". "Latest version" is defined as the version in effect on the date of bid submittal. Federal Standards and Military Standards can be accessed on-line via the Defense Logistics Agency's "Assist" Quicksearch web site: http://assist.daps.dla.mil/quicksearch/. PALLETIZATION Pallet Configuration: The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, double-face non-reversible pallets. Pallet lumber used shall be bark free. Pallet Load Size: The load plus the pallet shall have a maximum height of 53 inches and shall not exceed 2500 pounds in weight for shipments to Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (Sharpe). Pallet Load Configuration: The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Palletized loads shall be secured to the pallet to insure that the load arrives intact. Stacking Strength: The pallet plus the load shall be capable of supporting three additional like loads without any product damage and without the load or the pallet collapsing. Vertical, horizontal, or filler reinforcement may be added as necessary to provide strength. Partial Palletized Loads: Less than one-half pallet loads shall not be used for stacking, unless load is balanced on pallet. The partial palletized load shall be used for top loading only. Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published Guidelines for Regulating Wood Packaging Material in International Trade . Countries endorsing the IPPC Guidelines are found at the website given below. General Services Administration Acquisition Manual (GSAM) Clause 552.211-89 requires non-manufactured wood pallets and other non-manufactured wood packaging material used to pack items for delivery to or through IPPC countries be marked and properly treated in accordance with IPPC guidelines. Pallets and packing material shipped to FAS distribution facilities designated for possible delivery to the countries endorsing the IPPC Guidelines will comply with DLAD 47.305-1, and MIL-STD-2073-1. http://www.aphis.usda.gov/import_export/plants/plant_exports/wpm/country/index.shtml.