BAR, METAL

BAR,METAL
BAR, METAL
STEEL, CARBON
HOT ROLLED, ROUND
0.750 IN DIA
10 TO 20 FT LG
1.500 LB/FT (REFERENCE)
CHEMICAL COMPOSITION: CARBON 0.35% (MAX)<(>,<)>
SULPHUR 0.050% (MAX), PHOSPHORUS 0.050% (MAX)
TENSILE STRENGTH: 60,000 P.S.I. (MIN)
YIELD POINT (0.01% OFFSET) 30,000 P.S.I. (MIN)
PHYSICAL PROPERTIES: ELONGATION IN 2 INCHES:
LONGITUDINAL 30% (MIN). REDUCTION OF AREA:
LONGITUDINAL 45% (MIN). COLD BEND WITHOUT
CRACKING LONGITUDINAL 180 DEGREES TO INNER
DIAMETER OF 1/2 INCH
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
Metal Certification Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-METALSCERT is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
A Certificate of Quality Compliance (Mill-Material Certification) is required. A copy of the Certificate of Quality Compliance shall be provided with every shipment to the customer or DLA depot, and a copy of the Certificate of Quality Compliance provided for each shipment shall be forwarded to the DLA Troop Support Contracting Officer identified on the award.
CONTINUOUS IDENTIFICATION MARKINGS ARE REQUIRED IN ADDITION TO THE
MARKING REQUIREMENTS CITED IN THE PROCUREMENT SPECIFICATION:
AS A MINIMUM, EACH UNIT OF ISSUE (FEET,PLATE, OR SHEET) SHALL BE
SPE8E4-27-T-0101
SECTION B
IDENTIFIED WITH THE (1) DLA CONTRACT DELIVERY ORDER NUMBER, (2) NSN, (3)
SPECIFICATION NUMBER AND REVISION, (4) GRADE,CLASS & TYPE, ALLOY, PART
NUMBER,DIE NUMBER, AND TEMPER, (5) MANUFACTURER'S NAME, HEAT AND LOT
NUMBER, (6) DIMENSIONS.
MATERIAL SHALL BE SUPPLIED WITHIN THE REQUIRED MIN-MAX LENGTH
REQUIREMENTS AND MUST IN WHOLE FEET LENGTH ONLY (I.E. 10, 11, OR 12 FT
EVEN)
PERMISSIBLE MARKING METHODS ARE STAMPING (EXCEPT DIE STAMP) OR
STENCILING. THE CHARACTERS SHALL BE OF SUCH A SIZE AS TO BE LEGIBLE AND
VISIBLE TO THE UNAIDED EYE. THE MARKING FLUID APPLIED SHALL NOT
CONTAMINATE, OR OTHERWISE HAVE A DETRIMENTAL EFFECT ON THE PRODUCT OR
ITS PERFORMANCE. THE MARKINGS SHALL BE WATERPROOF AND SUFFICIENTLY
STABLE TO WITHSTAND NORMAL HANDLING.
IN LIEU OF "LINE MARKINGS", ADHESIVE LABELS ARE REQUIRED FOR EACH UNIT
OF STRAIGHT BARS, TUBES AND SHAPES, UNDER 0.250 INCHES IN NOMINAL OD,
AND TO BE SECURELY FASTENED. TAGS WILL BE ACCEPTABLE METHOD FOR WIRES.
FAILURE TO COMPLY WILL BE CAUSE FOR REJECTION OF END PRODUCT."
IY010: QUALIFIED SUPPLIERS LIST FOR DISTRIBUTORS (QSLD) REQUIREMENT (DLA
TROOP SUPPORT JUNE 1994) FOR FSG'S 95 AND 96.
ONLY SUPPLIERS LISTED ON THE QSLD ARE ELIGIBLE FOR AN AWARD PURSUANT TO
THIS SOLICITATION.
SUPPLIERS NOT QUOTING IN COMPLIANCE WITH THE QSLD REQUIREMENT MUST
INDICATE THEY ARE DEVIATING FROM THE REQUIREMENTS OF THE SOLICITATION.
ANY BID/QUOTE/OFFER BASED ON A PRODUCT SUPPLIED BY OTHER THAN AN
APPROVED QSL DISTRIBUTOR, EVEN THOUGH THE PRODUCT MIGHT HAVE BEEN
MANUFACTURED IN ACCORDANCE WITH THE DRAWING(S) AND/OR SPECIFICATION(S)
AS CITED IN THE PURCHASE ORDER
TEXT (POT) IS A BID/QUOTE/OFFER WITH EXCEPTION AND MUST BE SO INDICATED
BY THE
QUOTER/OFFEROR.
ANY PRODUCT FURNISHED UNDER A CONTRACT OR ORDER FOR A PRODUCT DESIGNATED
AS PART OF THE QSL PROGRAM, UNLESS SPECIFICALLY AUTHORIZED BY THE
GOVERNMENT IN WRITING, MUST FULLY COMPLY WITH THE TERMS AND CONDITIONS
OF THE QSL PROGRAM. ANY PRODUCT, WHICH DOES NOT FULLY COMPLY WILL BE
CONSIDERED AN UNAUTHORIZED SUBSTITUTION, AND MAY YIELD CRIMINAL
PENALTIES IN ADDITION TO ANY CIVIL REMEDIES AVAILABLE TO THE GOVERNMENT.
FOR THIS SOLICITATION, AND ANY RESULTING ORDER ISSUED TO AN APPROVED
QSLM/QSLD SUPPLIER
WHOSE QUOTE IS BASED ON COMPLIANCE WITH THE QSL PROGRAM, (EXCEPT IN THE
CASE OF FMS (FOREIGN MILITARY SALE) REQUIREMENTS), REFERENCES TO SOURCE
INSPECTION ARE HEREBY WAIVED. IN SUCH CASES, COQC, PVT, QAP-EQ003, ASQ
H1331, AND RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS, IF
REFERENCED, DO NOT APPLY.
FOR MORE INFORMATION ABOUT THE QSL PROGRAM GO TO THE FOLLOWING WEBSITE:
https://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Tech nical-services/Qualified-Suppliers-List/
-ORWRITE TO: DLA TROOP SUPPORT, ATTN: DLA TROOP SUPPORT FHTF, BLDG 3/B, 700 ROBBINS AVENUE, PHILADELPHIA, PA 19111-5092
Qualification requirements in procurement note #M03 Qualified Suppliers List for Manufacturers (QSLM)/Qualified Suppliers List for Distributors (QSLD) for Troop Support# apply. The full text of procurement note M03 can be found in the DLA Directive (DLAD) of Procurement Notes on the Web at: https://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.
SPE8E4-27-T-0101
SECTION B
(END STO)
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC NON GOVT STD ASTM A 29/A 29M-05 REVISION NR DTD PART PIECE NUMBER: CLASS B HOT ROLLED
TDP Rev A Gen 1 IAW REFERENCE QAP 13873 CDRL-METALSCERT-26124 REVISION NR DTD 12/04/2025 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE NON GOVT STD SAE AMS2806 REVISION NR D DTD 12/20/2018 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018589120 0001 FT 327.000
NSN/MATERIAL:9510001897442
DELIVERY (IN DAYS):0149
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 10% MINUS 10%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:020 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:00 OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PRESERVATION ZZ = IAW ASTM A700 PACKING Z = ASTM A700 MARKING IAW MIL-STD-129
IP083: Packaging, Marking, and Shipping of Metal Plating, Sheets, and other Metal Products ADDITIONAL MARKING REQUIREMENTS: WHEN THE CONTRACT OR ORDER REFLECTS TWO UNITS (EXAMPLE: FT-LB, LB-SH, LB-CL, ETC.) SHIPMENT MARKINGS SHALL INCLUDE THE
SPE8E4-27-T-0101
SECTION B
PR: 7018589120 PRLI: 0001 CONT’D
QUANTITY OF BOTH UNITS. THIS MARKING
DOES NOT APPLY FOR MATERIAL SHIPPED LOOSE.
PARCEL POST ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN RD
REC WHSE 57
TRACY CA 95304-5000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN ROAD
25600 S CHRISMAN RD REC WHSE 57
TRACY CA 95304-5000
US
Need Ship Date:03/28/2027 Original Required Delivery Date:05/29/2027
SPE8E4-27-T-0101 NSN/Part Number: 9510-00-189-7442 Quantity: 327 FT Purchase Request: 7018589120QTY: 327 Delivery: 149 days ADO