BEARING, BALL, AIRFRAME

BEARING,BALL,AIRFRAME
BEARING, BALL, AIRFRAME.
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
THIS IS A PERFORMANCE REVIEW INSTITUTE (PRI) QML OR QPL ITEM. PRODUCT
SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED
MANUFACTURER (FOR COMPONENTS) AND/OR ASSEMBLED BY AN ACCREDITIED
MANUFACTURER OR ACCREDITED ASSEMBLING DISTRIBUTOR (FOR ASSEMBLIES) AS
LISTED IN THE PRI QUALIFIED MANUFACTURER LIST (QML)OR QUALIFIED PRODUCTS
LIST (QPL) FOR THIS STANDARD. THE QML OR QPL IS AVAILABLE AT
WWW.EAUDITNET.COM.
THE FOLLOWING SHALL APPLY TO ALL
TECHNICAL DRAWINGS WHICH DO NOT BEAR A
DISTRIBUTION STATEMENT AS REQUIRED BY
OPNAVINST 5510.1H:
EXCEPT FOR FIXED, LANDBASED ARRESTING GEAR:
ALL LAUNCH AND RECOVERY EQUIPMENT, INCLUDING
COMPONENTS, PARTS, ACCESSORIES, ATTACHMENTS AND
ASSOCIATED EQUIPMENT (INCLUDING GROUND SUPPORT
EQUIPMENT), SPECIFICALLY DESIGNED OR MODIFIED
FOR LAUNCH AND RECOVERY EQUIPMENT, FALL UNDER
THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS,
22CFR PART 121.1, CATEGORY VIII, VOL 49, NO. 236
OF THE FEDERAL REGISTER AND IS CONSIDERED EXPORT
CONTROLLED TECHNOLOGY.
A. ALL SPECIFICATION CONTROL, SOURCE CONTROL,
INTERFACE CONTROL AND ALTERED ITEM DRAWINGS
SHALL BE GOVERNED BY DISTRIBUTION STATEMENT A OF
OPNAVINST 5510.1H AND ARE CLEARED FOR PUBLIC
RELEASE.
B. ALL OTHER DRAWINGS AND TECHNICAL DOCUMENTS
SHALL BE GOVERNED BY DISTRIBUTION STATEMENT D OF
OPNAVINST 5510.1H AND ARE CLEARED FOR USE BY DOD
AND DOD CONTRACTORS ONLY. UPON COMPLETION OF
THE CONTRACT, ALL DOCUMENTS WILL BE DESTROYED BY
ANY METHOD THAT WILL PREVENT DISCLOSURE OF
CONTENTS OR RECONSTRUCTION OF THE DOCUMENT.
NOTE 2: SECTION 326 OF THE 1993 DEFENSE
AUTHORIZATION ACT PLACES RESTRICTIONS ON THE USE
OF CLASS I OZONE DEPLETING SUBSTANCES (ODS).
UNTIL SUCH TIME AS THESE CLASS I ODSS ARE
ELIMINATED FROM MILITARY DRAWINGS AND
SPECIFICATIONS (INCLUDING SECOND TIER, I.E.,
THOSE SPECIFICATIONS LISTED IN THE
SPECIFICATIONS LISTED ON THE DRAWINGS), THE
FOLLOWING SHALL APPLY:
SPE4A6-27-T-4379
SECTION B
1. THE CONTRACTOR SHALL USE A GOVERNMENT
APPROVED NON-OZONE DEPLETING SUBSTANCE.
2. IF A GOVERNMENT APPROVED NON-OZONE DEPLETING
SUBSTANCE IS UNKNOWN/UNAVAILABLE, THE CONTRACTOR
SHALL CONTACT 4.8.1.4 AT NAWCAD LAKEHURST FOR AN
ACCEPTABLE SUBSTITUTE, AN ALTERNATE PROCESS OR A
WAIVER OF THE REQUIREMENT.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RT001: MEASURING AND TEST EQUIPMENT
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST MEET QPL/QML
REQUIREMENTS. BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE
QPL/QML COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE APPLICABLE
QPL(S)/QML(S).
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SPE4A6-27-T-4379
SECTION B
PN: MS27645-4A
SHELF LIFE 60 MONTHS:
RS023: Shelf-life requirement RS001 for a TYPE I (CODE S) item with a shelf life of 60 months (non-extendable) applies to this item.
CRITICAL APPLICATION ITEM
TDP Rev C Gen 3 IAW BASIC NON GOVT STD SAE AS7949C REVISION NR C DTD 09/01/2019 PART PIECE NUMBER: MS27645-4A
TDP Rev C Gen 3 IAW REFERENCE QAP 13873 QAP-B02 REVISION NR B DTD 12/11/2013 PART PIECE NUMBER:
TDP Rev C Gen 3 IAW REFERENCE NON GOVT STD SAE AS27645C REVISION NR C DTD 01/01/2016 PART PIECE NUMBER: QPL-AS7949-QPD
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018745668 0001 EA 22.000
NSN/MATERIAL:3110000424807
DELIVERY (IN DAYS):0171
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z
UNIT CONT:ZZ OPI:M
INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:32 -32 Type I, shelf life
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
ADDITIONAL INFORMATION: PRESERVATION, PACKAGING, PACKING, AND MARKING REQUIREMENTS SHALL BE IN ACCORDANCE WITH MIL-DTL-197M.
SPE4A6-27-T-4379
SECTION B
PR: 7018745668 PRLI: 0001 CONT’D
1. METHOD OF PRESERVATION SHALL BE DETERMINED BY
BEARING TYPE AND SIZE (REFER TO TABLE I).
2. PARAGRAPH 3.10.2, SELECTION OF UNIT
PRESERVATION, APPLIES. PROTECTIVE LUBRICANT OR
PRESERVATIVE COMPOUND SHALL BE DETERMINED
DEPENDENT UPON BEARING TYPE AND CLOSURE IN
ACCORDANCE WITH PARAGRAPH 3.3.4 AND TABLE II.
FOR PRESERVATION PROCESS CONTROLS, DEPENDANT
UPON BEARING TYPE, CLOSURE, AND LUBRICANT<(>,<)>
PARAGRAPHS 3.4 THROUGH 3.9 APPLY.
3. PACKAGING PRECAUTIONARY MARKING REQUIREMENTS
OF PARAGRAPH 3.12.4 APPLY.
4. CONTRACTOR'S PACKAGING FACILITY SHALL ADHERE
TO THE QUALITY ASSURANCE VERIFICATION
REQUIREMENTS AS CONTAINED WITHIN SECTION 4 OF
MIL-DTL-197M.
...END OF SPECIAL PACKAGING NSN/Part Number: 3110-00-042-4807 Quantity: 22 EA Purchase Request: 7018745668QTY: 136 Delivery: 171 days ADO