This Solicitation opportunity from Department Of Defense was posted on May 4, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
BOLT, CLOSE TOLERANC
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This contract specifies the procurement of a close-tolerance bolt identified by part number NAS6803AH2 and NSN 5306013199885, with a required quantity of four units. The item must comply with the current revision of the non-government standard NAS6803 through NAS6820, and any hardware produced after the solicitation date must adhere to the latest revision of that standard, with prior revisions acceptable only for previously manufactured items. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, referenced by R and I numbers, which override any conflicting provisions including packaging standards like ASTM D3951. Inspection and acceptance are to occur at origin, with sampling conducted in accordance with MIL-STD-1916 or an equivalent zero-based sampling plan; critical, major, and minor attributes are assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively. All items must be marked per MIL-STD-130N, including surface finish per ASME B46.1 and dimensional tolerances per ASME Y14.5, and must be packaged and labeled per MIL-STD-129 under RP001 packaging directives. Unit of issue is each, at a unit price of $4.00 for a total price of $16.00, with no variance allowed in quantity. Delivery is FOB origin with a required delivery date of 130 days from contract award, targeting shipment by September 20, 2026, and original required delivery by November 29, 2026. Packaging must conform to DLA packaging requirements, including palletization as defined in RP001, and all markings must reflect government property handling per MIL-STD-130N. Unit of issue and quantity per unit pack are strictly defined in the contract. Inspection and acceptance occur at origin, and no unique item identification is required under DFARS 252.211-7003(c)(1)(i). Transportation and shipping instructions follow DLAD Proc Notes C19 and C20, with delivery address specified as Hill AFB, Utah. The solicitation number is SPE4A1-26-T-1990, issued by the Department of Defense’s Aviation Supply Chain, with a response deadline of May
General Info
Agency
Contract Value
$1,024NAICS
Place of Performance
7537 WARDLEIGH RD, HILL AFB, UT, 84056-5734, USASet-Aside
Awardee
Award Issued Date
Documents
(1)AI Contract Breakdown
Uniform Contract FormatWhat is UCF?
Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.
Timeline
Submission Closed
Organization & Contact Information
Full Description
BOLT,CLOSE TOLERANCE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
SPE4A1-26-T-1990
SECTION B
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
ENGINEERING NOTES AND EXCEPTIONS:
1. MIL-STD-130 MARKING US MILITARY PROPERTY
2. SURFACE FINISH IAW ASME B46.1
3. DIMENSIONS TOLERANCES IAW ASME Y14.5
CRITICAL APPLICATION ITEM
IAW BASIC NON GOVT STD NAS6803 THRU 6820
REVISION NR 10 DTD 12/31/2024
PART PIECE NUMBER: NAS6803AH2
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7016048872 0001 EA 4.000
NSN/MATERIAL:5306013199885
DELIVERY (IN DAYS):0130
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA-QUP:001
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3210
DLA DISTRIBUTION DEPOT HILL
7537 WARDLEIGH RD
HILL AFB UT 84056-5734
US
SPE4A1-26-T-1990
SECTION B
PR: 7016048872 PRLI: 0001 CONT’D
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3210
DLA DISTRIBUTION DEPOT HILL
DDHU CML 385-519-8103
7537 WARDLEIGH RD BLDG 849W
HILL AFB UT 84056-5734
US
Need Ship Date:09/20/2026 Original Required Delivery Date:11/29/2026
SPE4A1-26-T-1990 NSN/Part Number: 5306-01-319-9885 Quantity: 4 EA Purchase Request: 7016048872QTY: 4 Delivery: 130 days ADO
More opportunities from Department Of Defense → AVIATION SUPPLY CHAIN
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS