BOLT, SHEAR

BOLT,SHEAR
BOLT, SHEAR
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
Casting/forging may be required to manufacture this NSN and tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains DSCC.cast.forge@dla.mil. Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
SPE4A6-26-T-34LL
SECTION B
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
THIS NSN IS PROCURED AS FULLY COMPETITIVE IN
ACCORDANCE WITH A MILITARY / FEDERAL
SPECIFICATION/STANDARD. SEE NSN/Part Number: 5306-01-360-4824 Quantity: 11 EA Purchase Request: 7018368289QTY: 11 Delivery: 20 days ADO