BRAND NAME OR EQUAL Carver Pump

The purpose of this modification is to incorporate the below Statement of Work, change the quantity from 1 each to 2 each and extend the close date to 01/07/2019. STATEMENT OF WORK FOR RECIRCULATION PUMP This Statement of Work (SOW) establishes and defines the requirements for manufacturing and delivering two identical recirculation pumps with motors for the 5" Dowel Rod facility at NSWC Indian Head. Prices shall include shipping costs. 1.1 SCOPE The recirculation pumps must be a Carver Pump (order code GVS-BDG-XCZ-KZZ) or equivalent with salient characteristics as defined in Section 2.0. Other deliverables include electronic copies of pump and motor assembly drawings. These drawings are required for NSWC IHEODTD Safety Office approval. A vendor shall not be selected until pumps and motor combinations are approved for use by NSWC IHEODTD Safety Office. 2.0 REQUIREMENTS The pumps are to be a Carver Pump (order code GVS-BDG-XCZ-KZZ) or equivalent with additional requirements throughout this section. Based on the current pump, it shall be an equivalent of Carver Pump Serial Number 157490. The GV Series TechBook will be provided with this SOW for reference. The salient characteristics are as follows: Two Carver GVS 3 x 2.5 x 7 pumps, or equivalent All 316SS 36" column Carbon Graphite externally flushed line shaft bearings with no external lubrication No suction strainer or inlet tailpipe Two Siemens Motor Model 1MJP2152YK62, or equivalent (see Section 3.0 for pump details) Motor mounting plate in accordance with Section 2.1 2.1 MOTOR MOUNTING PLATE Using The GV Series Techbook, Dwg: SP-GV-5, Rev: 0 as a guide, motor mount shall be sized according to the chart below and the rendering photo with no thru holes on the corners. See Figure 1see provided drawing3 x 2 1/2 x 714 3/414 5/82 1/245.9 + column depth10.63N/APump DimensionsPump SizeDischarge SizeABCDEFG Chart 1: Figure 1: A drawing of the motor mount shall be provided prior to vendor selection. A vendor shall not be selected until motor mount drawing is approved by Daniel Martin, M12 and Robert (Gregg) Frederick, M12. 3.0 ADDITIONAL INFORMATION A pump tag for the current pump could not be found. The Final Assembly Tag provided for the current pump and motor at the time of purchase can be found below. Figure 2: Figure 3: Figure 4: 4.0 DELIVERABLES Documentation deliverables shall be delivered to the Technical Point of Contact for arrangement or review and approval/acceptance: Technical Point of Contact 1: Naval Surface Warfare Center, IHEODTD Attn: Daniel Martin, Code M12DM 4895 McMahon Rd., Suite 107, Rm. 111 Indian Head, MD 20640-5126 Email: contact@example.gov ph: +1 (555) 000-0000 Technical Point of Contact 2: Naval Surface Warfare Center, IHEODTD Attn: Robert (Gregg) Frederick, Code M12 4895 McMahon Rd., Suite 107, Rm. 111 Indian Head, MD 20640-5126 Email: contact@example.gov ph: +1 (555) 000-0000 Material deliverables as specified below shall be delivered to the Production Point of Contact, for arrangement of inspection and acceptance: Production Point of Contact: Naval Surface Warfare Center, IHEODTD Attn: Zelda Brown, Code MP1ZB Email: contact@example.gov Ph: +1 (555) 000-0000 Delivery Address: Naval Surface Warfare Center, IHEODTD Receiving Attn: Zelda Brown, Code MP1ZB Receiving Officer, Bldg 116 4522 McMahan Road, Suite 100 Indian Head, MD 20640-5125 Deliverables Deliverable Quantity Due Pump and Motor Assembly 2 Based on specific manufacturer lead-time Electronic Copies of Motor and Pump Assembly 2 Prior to Vendor selection Electronic Drawings of Motor Mounting Plate 2 Prior to Vendor selection Current Motor Identification Tag 2. Current Motor Identification Tag 1. Final Assembly Tag for Carver Pump SN 157490.Required motor mount geometry rendering. Note that there shall be no thru holes. Motor mounting plate dimensions (in inches). 1.0 INTRODUCTION