This Solicitation opportunity from Department Of Defense was posted on July 17, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
CABLE ASSEMBLY, SPEC
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This contract solicitation, identified as SPE4A6-26-T-048M, calls for the procurement of a single unit of a CABLE ASSEMBLY, SPEC, identified by NSN 6150015408033, with delivery required within 20 days of award to a destination address associated with USS SOMERSET LPD 25 at FPO AP 96678. The contract specifies FOB Destination as the point of transfer for risk and responsibility, with inspection and acceptance also occurring at the destination. Packaging must strictly comply with MIL-STD-2073-1E, including detailed packaging data codes for pressure methods, containment, cushioning, and unit control, while palletization and marking adhere to DLA’s RP001 packaging requirements and MIL-STD-129 standards, with no special marking required. The item is subject to rigorous quality control provisions, including sampling per MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based sampling plan, where acceptance requires zero non-conformances unless otherwise stated, and attributes are assigned verification levels or AQLs of VII/0.1 for critical, IV/1.0 for major, and II/4.0 for minor, with unspecified attributes treated as major. Technical and quality requirements are incorporated by reference from the DLA Master List of Technical and Quality Requirements via R and I numbers. The contract imposes extensive compliance obligations tied to cybersecurity, supply chain integrity, and regulatory requirements. Offerors must implement NIST SP 800-171 safeguards and maintain a current assessment of their information systems not older than three years, with access granted for government assessment. They must also comply with DFARS and FAR clauses prohibiting acquisition of covered telecommunications equipment, restricting the use of mandatory arbitration agreements, safeguarding defense information, and prohibiting hexavalent chromium and other hazardous materials, with additional obligations under Buy American, Berry Amendment, and Trade Agreements provisions. The solicitation excludes offerings involving additive manufacturing unless specifically authorized, and requires prior submission of a Material Safety Data Sheet for award consideration. Payment must be submitted electronically via Wide Area Workflow, requiring contractor registration in SAM and WAWF. Offerors must maintain current and accurate SAM representations, including certifications on foreign ownership, child labor, and prohibited telecommunications equipment, and submit all quotations exclusively through the DIBBS portal prior to the November 25, 2
General Info
Place of Performance
UNIT 100232 BOX 1, FPO, AP, 96678, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
CABLE ASSEMBLY,SPEC
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICATION LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
LEIDOS INC 1N0X4 P/N 593-8788913 ASSY 90
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://www.dla.mil/Portals/104/Documents/DLMS/eApplications/LogDataAdmin/ UnitofIssueandPurchaseUnit.xlsx
SPE4A6-26-T-048M
SECTION B
PR: 7014394069 PRLI: 0001 CONT’D
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7014394069 0001 EA 1.000
NSN/MATERIAL:6150015408033
DELIVERY (IN DAYS):0020
DELIVER FOB: DESTINATION
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:C
UNIT CONT:E5 OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
R23181
USS SOMERSET LPD 25
UNIT 100232 BOX 1
FPO AP 96678
US
VESSEL SHIPMENT. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANSPORTATION SEE DLAD PROC
NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
R23181
SOMERSET LPD 25
DLA VENDORS: USE VSM FOR
US
RDD 777 SHIPMENT. SHIP BY FASTEST TRACEABLE MEANS. DO NOT USE PARCEL POST.
M/F: (TCN) R231815161EM17
RDD: 777
PROJ: LK5 TP 2
SUPP ADD: YNEB14 SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 05
DIC: A4A DIST: 9B ADV: FC: NR
Need Ship Date:00/00/0000 Original Required Delivery Date:06/16/2025
SPE4A6-26-T-048M
SECTION B
PR: 7014394069 PRLI: 0001 CONT’D
SPE4A6-26-T-048M NSN/Part Number: 6150-01-540-8033 Quantity: 1 EA Purchase Request: 7014394069QTY: 1 Delivery: 20 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Earlier notices in this NAICS code
Posted before this notice, open and closed
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 750+ contractors already using CLEATUS