CONTRACTOR FIRST ARTIC

COVER,GUN MUZZLE
COVER, MUZZLE, RUBBER
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN
AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS
REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT
CONTROL ACT (22 U.S.C.A. 2778-2799). ANY
MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS
REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE
TRADE CONTROLS (DDTC), DEPARTMENT OF STATE.
DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED
PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS
APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC
REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER
INELIGIBLE FOR AWARD.
______________EXCEPTION DATA_________________
ON DWG 11579102, COVER MUZZLE, IN NOTE 1, CHANGE CANCELLED SPECIFICATION
MIL-STD-417 AND COMPOSITION TO:
NOTE 1: "RUBBER COMPOSITION M2 BG714 A14 B14 EO34 F17 PER ASTM D2000
____________END OF EXCEPTIONS_______________
THE ITEM BEING PROCURED IS A CRITICAL GUN PART
ITEM WITH UNIQUE REQUIREMENTS.
CONTRACTOR FAT APPLIES.
AFTER RECEIPT OF QUOTES, OFFERORS MAY BE
CONTACTED TO PRICE THE FAT REQUIREMENT.
PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA
QAR AT THE ACTUAL MANUFACTURER'S FACILITY
IDENTIFIED ON THIS CONTRACT. THE IDENTIFICATION
OF THE ACTUAL MANUFACTURER MUST BE SUBMITTED TO
THE CONTRACTING OFFICER FOR INCLUSION IN THE
AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST
BE APPROVED BY THE PCO VIA FORMAL CONTRACT
MODIFICATION.
SPE7L7-26-T-4760
SECTION B
PRODUCT VERIFICATION TESTING (PVT) IN ACCORDANCE
WITH PROCUREMENT NOTE E05, MAY BE INVOKED FOR THE
REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE
INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE
CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING
TESTING.
PRODUCT VERIFICATION TESTING, IF INVOKED<(>,<)>
WILL BE PERFORMED PRIOR TO ACCEPTANCE OF
EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE
PVT SAMPLES FROM EACH (SUB)CONTRACTOR USED
IN THE PRODUCTION OF PARTS ON THIS CONTRACT.
FIVE (5) PVT SAMPLES, UNLESS OTHERWISE
SPECIFIED, WILL BE REQUIRED TO BE IDENTIFIED
TO THOSE (SUB)CONTRACTORS WHEN THEY ARE SENT
IN FOR TESTING.
CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED.
*************************************************************
RD001: DEMILITARIZATION: SMALL ARMS WEAPONS AND PARTS AND ACCESSORIES
(CATEGORY I MUNITIONS LIST ITEMS, CATEGORY I-DODM 4160.28-VOL.3)
RD002, COVERED DEFENSE INFORMATION APPLIES
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RT001: MEASURING AND TEST EQUIPMENT
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
SPE7L7-26-T-4760
SECTION B
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 0001S00000053 Quantity: 118 EA Purchase Request: 7017868583QTY - See Solicitation Delivery: 312 days ADO