COUPLING HALF, QUICK DI

COUPLING HALF, QUICK DISCONNECT.
REF/PN: MS22068-7.
MIL SPEC TITLED,"COUPLING ASSEMBLIES, QUICK DISCONNECT<(>,<)>
AIRCRAFT LIQUID OXYGEN SYSTEMS", FEMALE QUICK
DISCONNECT END, MS33656 MALE FITTING END<(>,<)>
5/16 INCH O.D. TUBE SIZE, WITH CHECK VALVE<(>,<)>
AIRCRAFT LIQUID OXYGEN SYSTEM APPLICATION.
EXCEPTION DATA: LIQUID NITROGEN AND COMPRESSED
NITROGEN MAY BE USED AS AN ALTERNATE FOR
LIQUID OXYGEN AND COMPRESSED OXYGEN WHEN TESTING
THE QUICK DISCONNECTS.
.
REQUIRED MARKING: EACH UNIT AND SHIPPING CONTAINER SHALL BE MARKED IN
ACCORDANCE WITH MIL-STD-129. IN ADDITION, THE FOLLOWING PRECAUTIONARY
MARKING SHALL BE REQUIRED ON EACH UNIT PACKAGE AND SHIPPING CONTAINER
.
NSN, CONTRACT NUMBER, PART NUMBER, CAGE CODE AND ITEM NAME
.
CAUTION:
.
DO NOT STORE IN PROXIMITY OF PETROLEUM PRODUCTS
.
DO NOT ALLOW CONTAMINANTS OF ANY KIND TO BE USED ON OR ABOUT THE
OXYGEN COUPLINGS
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
THIS IS A NAVY IDENTIFIED CRITICAL SAFETY ITEM
(CSI).
ALL REQUESTS FOR WAIVERS OR DEVIATIONS MUST BE
FORWARDED TO THE DSC CONTRACTING OFFICER FOR
REVIEW AND APPROVAL.
.
ALL ITEMS OF SUPPLY SHALL BE MARKED IAW
MIL-STD-129. IN ADDITION, EACH UNIT PACK WILL
BE MARKED WITH LOT AND SERIAL NUMBER (IF AVAILABLE),
CONTRACTOR'S CAGE CODE, ACTUAL MANUFACTURER'S
CAGE CODE AND PART NUMBER.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for Manufacturers and Non-Manufacturers
If this NSN provides Contract Data Requirement Lists (CDRLs) as part of the Technical Data Package, the line items from this solicitation are not to be separately priced. Offerors must factor into the end item unit price all costs associated with the preparation and delivery of the
SPE7M1-27-Q-0191
SECTION B
SUPPLY/SERVICE: 4730-00-630-0310 CONT'D
data deliverables in the contract.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS IS A PERFORMANCE REVIEW INSTITUTE (PRI) QML OR QPL ITEM. PRODUCT
SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED
MANUFACTURER (FOR COMPONENTS) AND/OR ASSEMBLED BY AN ACCREDITIED
MANUFACTURER OR ACCREDITED ASSEMBLING DISTRIBUTOR (FOR ASSEMBLIES) AS
LISTED IN THE PRI QUALIFIED MANUFACTURER LIST (QML)OR QUALIFIED PRODUCTS
LIST (QPL) FOR THIS STANDARD. THE QML OR QPL IS AVAILABLE AT
WWW.EAUDITNET.COM.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC SPEC NR MS22068E NOT 2 REVISION NR E DTD 11/21/2023 PART PIECE NUMBER: TYPE I MS22068-7
TDP Rev A Gen 1 IAW REFERENCE SPEC NR MIL-C-21049F(1) NOT 2 REVISION NR F DTD 11/15/2023 PART PIECE NUMBER: QPL-21049
Critical Safety Item
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments%2FDLMS% 2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT.
0001 4730-00-630-0310 3.000 EA $ _______________ $ ______________
COUPLING HALF
,QUICK DISCONNECT
PRICING TERMS: Firm Fixed Price
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
SPE7M1-27-Q-0191
SECTION B
SUPPLY/SERVICE: 4730-00-630-0310 CONT'D
ACCEPTANCE POINT: ORIGIN
FOB: ORIGIN DELIVERY DATE: 410 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:31 CLNG/DRY:Z PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:GT CUSH/DUNN THKNESS:A
UNIT CONT:D3 OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:100
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
Z = CLEANING/DRYING: Per MIL-C-21049, cleaning shall be accomplished with MIL-STD-1359. Cleaning by immersion shall not be permitted on the completed coupling assembly. ATTENTION: Per ASSIST Quick Search, MIL-STD-1359 is S/S BY SAE-ARP1176.
PRODUCT'S OPENINGS SHALL BE CLOSED WITH EITHER ALUMINUM OR NONCORROSIVE PLASTIC PLUGS OR END CAPS IN ACCORDANCE WITH MIL-C-5501 TO ENSURE NO DEBRIS WILL CONTAMINATE PRODUCT FLOW WHEN IN OPERATION.
CUSHIONING MATERIAL MUST NOT BE APPLIED WITHIN INNER BAG DUE TO CLEANLINESS OF PART.
ZIP LOCK BAGS SHALL NOT BE USED.
ZZ = SPECIAL MARKING REQUIREMENTS FOR BARRIER BAGS:
CLEANED FOR OXYGEN SERVICE.
DO NOT ALLOW PETROLEUM CONTAMINANTS OF ANY KIND TO BE USED/STORED ON OR ABOUT THESE CONTAINERS.
EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN, CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.
OPEN FOR USE ONLY.
ATTENTION: EACH UNIT CONTAINER (BOX) AND SHIPPING
CONTAINER SHALL BE MARKED IN ACCORDANCE WITH
MIL-STD-129. IN ADDITION, THE FOLLOWING PRECAUTIONARY
MARKING SHALL BE REQUIRED ON EACH UNIT CONTAINER (BOX)
AND SHIPPING CONTAINER:
CAUTION:
DO NOT STORE IN PROXIMITY OF PETROLEUM PRODUCTS
DO NOT ALLOW CONTAMINANTS OF ANY KIND TO BE
USED ON OR ABOUT THE OXYGEN COUPLINGS.
If Product First Article Testing (FAT) is required and a Packaging FAT is included in the Special Packaging Instruction or Drawing, the Packaging FAT requirement is invoked. If there is no Product FAT, no Packaging FAT is required.
SPE7M1-27-Q-0191
SECTION B
SUPPLY/SERVICE: 4730-00-630-0310 CONT'D
PARCEL POST ADDRESS:
SW3218
DLA DISTRIBUTION SAN DIEGO
3581 CUMMINGS ROAD BLDG 3581
SAN DIEGO CA 92136-3581
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND
CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3218
DLA DISTRIBUTION SAN DIEGO
3581 CUMMINGS ROAD BLDG 3581
SAN DIEGO CA 92136-3581
US
ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT.
0002 4730-00-630-0310 419.000 EA $ ______________ $ ______________
COUPLING HALF
,QUICK DISCONNECT
PRICING TERMS: Firm Fixed Price
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
FOB: ORIGIN DELIVERY DATE: 410 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:31 CLNG/DRY:Z PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:GT CUSH/DUNN THKNESS:A UNIT CONT:D3 OPI:M INTRMDTE CONT:E5 INTRMDTE CONT QTY:100 PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
Z = CLEANING/DRYING: Per MIL-C-21049, cleaning shall be accomplished with MIL-STD-1359. Cleaning by immersion shall not be permitted on the completed coupling assembly. ATTENTION: Per ASSIST Quick Search, MIL-STD-1359 is S/S BY SAE-ARP1176.
PRODUCT'S OPENINGS SHALL BE CLOSED WITH EITHER ALUMINUM OR NONCORROSIVE PLASTIC PLUGS OR END CAPS IN ACCORDANCE WITH MIL-C-5501 TO ENSURE NO DEBRIS WILL CONTAMINATE PRODUCT FLOW WHEN IN OPERATION.
CUSHIONING MATERIAL MUST NOT BE APPLIED WITHIN INNER BAG DUE TO CLEANLINESS OF PART.
SPE7M1-27-Q-0191
SECTION B
SUPPLY/SERVICE: 4730-00-630-0310 CONT'D
ZIP LOCK BAGS SHALL NOT BE USED.
ZZ = SPECIAL MARKING REQUIREMENTS FOR BARRIER BAGS:
CLEANED FOR OXYGEN SERVICE.
DO NOT ALLOW PETROLEUM CONTAMINANTS
OF ANY KIND TO BE USED/STORED ON OR
ABOUT THESE CONTAINERS.
EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,
CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE
CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.
OPEN FOR USE ONLY.
ATTENTION: EACH UNIT CONTAINER (BOX) AND SHIPPING
CONTAINER SHALL BE MARKED IN ACCORDANCE WITH
MIL-STD-129. IN ADDITION, THE FOLLOWING PRECAUTIONARY
MARKING SHALL BE REQUIRED ON EACH UNIT CONTAINER (BOX)
AND SHIPPING CONTAINER:
CAUTION:
DO NOT STORE IN PROXIMITY OF PETROLEUM PRODUCTS
DO NOT ALLOW CONTAMINANTS OF ANY KIND TO BE
USED ON OR ABOUT THE OXYGEN COUPLINGS.
If Product First Article Testing (FAT) is required and a Packaging FAT is included in the Special Packaging Instruction or Drawing, the Packaging FAT requirement is invoked. If there is no Product FAT, no Packaging FAT is required.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:31 CLNG/DRY:Z PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:GT CUSH/DUNN THKNESS:A
UNIT CONT:D3 OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:100
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
Z = CLEANING/DRYING: Per MIL-C-21049, cleaning shall be accomplished with MIL-STD-1359. Cleaning by immersion shall not be permitted on the completed coupling assembly. ATTENTION: Per ASSIST Quick Search, MIL-STD-1359 is S/S BY SAE-ARP1176.
PRODUCT'S OPENINGS SHALL BE CLOSED WITH EITHER ALUMINUM OR NONCORROSIVE PLASTIC PLUGS OR END CAPS IN ACCORDANCE WITH MIL-C-5501 TO ENSURE NO DEBRIS WILL CONTAMINATE PRODUCT FLOW WHEN IN OPERATION.
CUSHIONING MATERIAL MUST NOT BE APPLIED WITHIN INNER BAG DUE TO CLEANLINESS OF PART.
ZIP LOCK BAGS SHALL NOT BE USED.
ZZ = SPECIAL MARKING REQUIREMENTS FOR BARRIER BAGS:
CLEANED FOR OXYGEN SERVICE.
SPE7M1-27-Q-0191
SECTION B
SUPPLY/SERVICE: 4730-00-630-0310 CONT'D
DO NOT ALLOW PETROLEUM CONTAMINANTS
OF ANY KIND TO BE USED/STORED ON OR
ABOUT THESE CONTAINERS.
EACH UNIT PACKAGE WILL BE MARKED WITH THE NSN,
CONTRACT NUMBER, LOT NUMBER, CONTRACTOR CAGE
CODE, MANUFACTURER CAGE CODE, AND PART NUMBER.
OPEN FOR USE ONLY.
ATTENTION: EACH UNIT CONTAINER (BOX) AND SHIPPING
CONTAINER SHALL BE MARKED IN ACCORDANCE WITH
MIL-STD-129. IN ADDITION, THE FOLLOWING PRECAUTIONARY
MARKING SHALL BE REQUIRED ON EACH UNIT CONTAINER (BOX)
AND SHIPPING CONTAINER:
CAUTION:
DO NOT STORE IN PROXIMITY OF PETROLEUM PRODUCTS
DO NOT ALLOW CONTAMINANTS OF ANY KIND TO BE
USED ON OR ABOUT THE OXYGEN COUPLINGS.
If Product First Article Testing (FAT) is required and a Packaging FAT is included in the Special Packaging Instruction or Drawing, the Packaging FAT requirement is invoked. If there is no Product FAT, no Packaging FAT is required.
PARCEL POST ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND
CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
GOVT USE
External External External Customer RDD/ ITEM PR PRLI PR PRLI Material Need Ship Date. 0001 7017233370 0001 N/A N/A N/A 07/07/2027
0002 7017233370 0002 N/A N/A N/A 07/07/2027

SPE7M1-27-Q-0191 NSN/Part Number: 4730-00-630-0310 Quantity: 3 EA Purchase Request: 7017233370QTY: 422 Delivery: 410 days ADO