CYLINDER, COMPRESSED GA

CYLINDER,COMPRESSED GAS,OXYGEN
CYLINDER, COMPRESSED GAS, OXYGEN EMPTY CYLINDER
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ034: HAZARDOUS COMMUNICATION STANDARD NOTICE
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
1000 LB WATER CAP., 27737 CU. IN. VOL CAP.
APPROX 30 IN. DIA BY 56 IN. O/A HEIGHT. WITH
FOOT RING. WITH VALVE PROTECTION HOOD AND HINGED
CAP. COMBINATION FORKLIFT AND LIFTING BRACKETS
DESIGNED TO ENABLE LIFTING OF FULL CYLINDERS
SHALL BE WELDED TO TOP HEAD.
A FLANGE WITH A 1 1/2 INCH NPT PLUG
SHALL BE PROVIDED IN TOP OF HEAD ONLY.
WHERE NECESSARY, THE TOP PLUG SHALL BE REPLACED
WITH A PRESSURE RELIEF DEVICE. THE VALVE FOR
LIQUID WITHDRAWAL OF PRODUCT SHALL BE SECURELY
EQUIPPED WITH A POLYPROPYLENE EDUCTION TUBE AND
ALUMINUM SLEEVE TO HOLD IT STRAIGHT. THE BOTTOM
END OF THE TUBE SHALL BE CUT AT TWO (2) 45
DEGREE ANGLES AND SHALL REACH TO WITHIN 1 INCH
OF BUT NOT TOUCH THE BOTTOM OF THE CYLINDER.
THE CYLINDER AND VALVE ASSEMBLIES WHALL BE
EQUIPPED WITH TYPE CG-7 PRESSURE RELIEF DEVICES
OF SUFFICIENT PRESSURE RATING AND FLOW CAPACITY
TO MEET ALL REQUIREMENTS OF CGA PAMPLET S-1.1.
THE CYLINDER SHALL BE COLOR CODED AND STENCILLED
PER MIL-STD-101B. THE CHEMICAL NAME SHALL BE
STENCILLED HORIZONTALLY IN TWO DIAMETRICALLY
OPPOSITE LOCATIONS TWO INCHES BELOW THE TOP HEAD
WELD SEAM. ANY MODIFYING WORDS SHALL BE
CENTERED 4 INCHES BELOW THE CHEMICAL NAME.
IF THE CYLINDER REQUIRES BANDS, THE CHEMICAL
NAME SHALL BE PLACED TWO INCHES BELOW THE LAST
BAND.
THE INTERIOR OF THE CYLINDER SHALL BE DRIED TO
A DEW POINT OF LESS THAN MINUS 30 DEGREES F
(-30 DEG F) AND THEN PRESSURIZED TO NOT LESS
THAN 5 NOR GREATER THAN 25 PSIG WITH DRY OIL
FREE NITROGEN OR ARGON HAVING A DEW POINT OF
LESS THAN MINUS 50 DEG F (-50 DEG F). THE
VALVES SHALL THEN BE TIGHTLY CLOSED TO
MAINTAIN A POSITIVE PRESSURE. THE CYLINDER
SHALL BE TAGGED AT THE VALVE "PURGED AND
SPE4A6-26-T-22EY
SECTION B
PRESERVED WITH A NONFLAMMABLE INERT GAS."
DESIGN APPROVAL BY DSCR-JDTA IS REQUIRED BEFORE
AWARD OF CONTRACT.
TREATMENT AND PAINTING OF CYLINDERS SHALL BE BY
ANY METHOD/SYSTEM THAT WILL PROVIDE A FINISH
THAT WILL MEET THE REQUIREMENTS OF COMPRESSED
GAS ASSOCIATION TB-17-2000. TESTS 1, 3, 5, 6
AND 8 APPLY.
THE PRODUCTS OFFERED MUST ALSO MAINTAIN A
COMMERCIAL MARKET ACCEPTABILITY RECORD FOR THE
DURATION OF ALL CONTRACTS. THE CONTRACTOR MUST
DEMONSTRATE YEARLY COMMERCIAL SALES TO SOURCES
OTHER THAN THE GOVERNMENT FOR THE LENGTH OF ALL
CONTRACTS AND MUST PROVIDE THIS UPDATE TO THE
CONTRACTING OFFICER OR THEIR DESIGNATED
REPRESENTATIVE. IN THE EVENT THE CONTRACTOR
ELECTS TO DROP THE PRODUCT FROM SALES TO THE
COMMERCIAL MARKET, THE CONTRACTOR SHALL
IMMEDIATELY NOTIFY THE CONTRACTING OFFICER OR
THEIR DESIGNATED REPRESENTATIVE. IN SUCH AN
EVENT, QUALITY ASSURANCE PROVISIONS WILL BE
UPGRADED, AT NO ADDITIONAL COST TO THE
GOVERNMENT, TO ASSURE THE PRODUCTS BEING
PROVIDED MEET ALL PERFORMANCE REQUIREMENTS.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
"SDS AND OSHA HAZARD WARNING/PRODUCT LABEL (HWL) ARE REQUIRED. THE SDS
AND HAZARD WARNING LABEL MUST BE REVIEWED AND APPROVED BY
CHEMISTS/TECHNICAL PERSONNEL BEFORE CONTRACT AWARD. THE APPROVED SDS AND
LABEL MUST THEN BE PLACED IN THE CONTRACT FILE AND A COPY FORWARDED TO
THE DLA AVIATION HMIRS OFFICE (VBA)."
THIS ITEM IS IDENTIFIED AS A COMMERCIAL OFF THE SHELF (COTS) ITEM
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
THIS MATERIAL DOES NOT HAVE A SHELF LIFE REQUIREMENT
EMPTY CYLINDER SIZE JUMBO "D" MEDICAL OXYGEN, ALUMINUM.
ALLIED HEALTHCARE BIDDER SHALL SPECIFY CO & P/N BEING SUPPLIED.
SPE4A6-26-T-22EY
SECTION B
UNIT OF ISSUE = EACH (EA), ONE EA EQUATES 2216PSI 22CU FT CAP, SIZE D,
M-22 JUMBO EMPTY CYLINDER.
ALLIED HEALTHCARE PRODUCTS, INC. 62842 P/N 31-10-0017
ALLIED HEALTHCARE PRODUCTS, INC. 62842 P/N 349-040
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017978617 0001 EA 1.000
NSN/MATERIAL:8120012731465
DELIVERY (IN DAYS):0020
DELIVER FOB: DESTINATION
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:ZZ OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PACKAGE IAW DOT FOR DOMESTIC SHIPMENTS. EXPORT SHIPMENTS SHALL BE PACKAGED IAW UN INTERNATIONAL REQUIREMENTS. DOMESTIC SHIPMENTS AND EXPORT SHIPMENTS SHALL BE MARKED IAW MIL-STD-129 MARKING REQUIREMENTS.
CYLINDERS THAT DO NOT LEND THEMSELVES TO USE OF A U.N. CERTIFIED 4G FIBERBOARD BOX DUE TO SIZE, WEIGHT, CONFIGURATION, ETC., SHALL BE PALLETIZED LOAD TYPE IX IAW MIL-STD-147.
PARCEL POST ADDRESS:
V21953
USS OSCAR AUSTIN DDG 79
UNIT 100315 BOX 1
FPO AE 09581
US
VESSEL SHIPMENT. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANSPORTATION SEE DLAD PROC
SPE4A6-26-T-22EY
SECTION B
PR: 7017978617 PRLI: 0001 CONT’D
NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
V21953
USS OSCAR AUSTIN DDG 79
DLA VENDORS: USE VSM FOR
US
RDD 777 SHIPMENT. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANSPORTATION SEE DLAD PROC
NOTE C20 AND CONTRACT
M/F: (TCN) V219536232HE16
RDD: 777
PROJ: EP5 TP 2
SUPP ADD: YNHE01 SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 04
DIC: A41 DIST: 9B ADV: FC: SC
Need Ship Date:00/00/0000 Original Required Delivery Date:08/25/2026
SPE4A6-26-T-22EY NSN/Part Number: 8120-01-273-1465 Quantity: 1 EA Purchase Request: 7017978617QTY: 1 Delivery: 20 days ADO