GASKET

GASKET
GASKET
NFES 0254 GASKET, FIRE HOSE: Shall be in accordance with current Forest Service Specification 5100-190C, and Amendment, with the following requirements and characteristics: Waterway Size 1-1/2 inches (nominal)
Unit of issue PG (10 gaskets per package) EXCEPTIONS TO FOREST SERVICE SPECIFICATION 5100-190C: 1) INSPECTION, SAMPLING AND TEST PROCEDURES: General inspection and tests: Unless otherwise specified in the contract or purchase order, the contractor is responsible for performance of all inspection requirements prior to submission for Government acceptance. The contractor may utilize their own facilities or any commercial laboratory acceptable to the Government. Inspection records of the examination and tests shall be kept complete and available to the Government. Inspection and test site: The contractor shall conduct lot acceptance inspection and tests to determine compliance with the specification. During any inspection, the inspector may take from the lot one or more samples and submit them to an independent test laboratory approved by the Government or to a government test facility for inspection and tests. Testing with referenced documents: The contractor is responsible for ensuring that components and materials used are manufactured, examined and tested in accordance with referenced specifications and standards. The Government reserves the right to perform any of the inspections or tests set forth in this section where such action is deemed necessary to assure supplies and services conform to prescribed requirements. Sampling for inspection: When inspection is performed, sampling shall be in accordance with ANSI/ASQ Z 1.4. Lot: All gaskets of one size presented together in one delivery shall be considered a lot for the purpose of inspection. A sample unit shall be one item. Sampling for visual and dimensional examination: Sampling for visual and dimensional examination shall be S-3, with an Acceptable Quality Level (AQL) of 2.5 percent defective. Visual and dimensional examination: Each sample gasket shall be visually and dimensionally examined to determine conformance with this item purchase description. Visual or dimensional defects shall be classified as major or minor. A defect not listed in Table 1 shall be classified as a minor defect. If the number of defects in any sample exceeds the indicated AQL, the lot shall be rejected. TABLE 1 Major Defects 1. Workmanship and finishing not as required 2. Material not as required 3. Dimensions not as required EXCEPTIONS TO FOREST SERVICE SPECIFICATION 5100-190C, AMENDMENT 1 1) Paragraph 3.2.1 (e) Gasket Material, Delete and replace with: The material used in the manufacture of the gaskets shall have a minimum shelf life of 10 years as determined by ARP 5316, Table 1.
Shelf life marking of the unit package is required to include manufacture date and expiration date.
CERTIFICATE OF CONFORMANCE: Certificates of Conformance are required in accordance with paragraph 3.3 of 5100-190C. PACKAGING: Ten (10) gaskets shall be packaged in a box or plastic bag and sealed. PACKING: Twenty (20) packages of gaskets (200 gaskets) shall be packed in a close-fitting corrugated fiberboard box, minimum burst strength 200 psi (minimum edge crush strength 32 lb per inch width), and shall be in compliance with the applicable freight regulations. SUPPLEMENTAL PACKING AND PACKAGING REQUIREMENTS: All fiberboard boxes, cushioning, and dunnage used in packing and packaging of this item shall contain recovered materials in accordance with the EPA Comprehensive Procurement Guideline for Products Containing Recovered Materials (40 CFR 247) and the EPA Paper Products Recovered Materials Advisory Notice (Federal Register, Vol. 61, No. 104, May 29, 1996). The EPA's Recommended Recovered Fiber Content Levels for Paperboard and Packaging Products are available at: http://www.epa.gov/osw/conserve/tools/cpg/products/paperbrd.htm http://www.epa.gov/osw/conserve/tools/cpg/products/paperbrd.htm MARKING:
SPE7M1-26-U-6971
SECTION B
Shipments to the Department of Defense (DOD) shall be marked in accordance with MIL-STD-129. SPECIAL MARKING: The National Fire Equipment System (NFES) number appearing below the National Stock Number (NSN) of this Item Purchase Description shall be marked on the shipping container below the NSN. The NFES number shall be preceded by "NFES". Palletization: The shipping (transport) containers shall be palletized. The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, and double-face non-reversible pallets. The palletized load shall not overhang the pallet deck board edge by more than 1 inch and shall not exceed 53 inches in overall height (including pallet). Less than half pallet loads or loads shipped by small package carrier in acceptable transport packing need not be palletized. When less than full but more than half pallet is used, the palletized load shall utilize proper bracing and/or reinforcement to ensure that the load can withstand two additional loads placed on it. Stacking: A load-stacking test shall be performed once, at the beginning of the contract, for each different unitized or palletized load configuration. A fully palletized load shall be tested utilizing a total stack of three palletized loads, with all the proper bracing and/or reinforcement necessary to perform the test. There shall be no evidence of damage to the pallets, shipping containers or products when the stack is tested on the rigid surface for a minimum of 24 hours, in compliance with all the National and Local Safety Regulations. The pre-tested palletized load configuration shall be duplicated using the same packaging materials, pattern, number of shipping (transport) containers, and procedures consistent throughout the duration of the contract. Palletized loads shall be stable and safe when handled with mechanical equipment by qualified personnel. Materials: All lumber used inside or outside shipping shall be bark free. No used wood pallets with repaired components or stringers will be acceptable. All wood pallet stringers shall be manufactured from hardwoods. Pallets manufactured materials other than wood, shall conform to all the requirements specified herein. Unitization: For the purpose of this requirement, the assembled group of containers or items in a single load that can be handled as a unit throughout the distribution system. Unitization encompasses, but is not limited to, consolidation in a container, placement on a pallet or load base having forklift capability or securely binding together. Shipments should be considered for unitization where appropriate or specified. Unitization of pallet load: The palletized load shall be unitized and secured to the pallet to ensure that the load arrives intact without product damage. The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Vertical, horizontal or filler reinforcement shall be added as necessary to meet the stacking strength requirements. A palletized load shall be secured to the pallet by shrink or stretch wrapping, and/or, by steel or nonmetallic strapping. When steel or non-metallic strapping is used, edge protectors shall be provided to prevent damage to the cartons when tensioning the strapping. As a minimum, two straps shall run lengthwise, two straps shall run widthwise, and two straps shall run around the girth of the palletized load. A palletized load shall be capable of protecting the products against damage in a multiple handling, transportation, and storage environment having distribution warehouses with rack systems that support the load/s overhead of warehouse personnel. Notice of special requirements for shipment to all countries that have endorsed the IPPC Guidelines for treatment of non-manufactured wood packaging: The International Plant Protection Convention (IPPC) has approved and published on March 15, 2002, "Guidelines for Regulating Wood Packaging Material in International Trade". Countries endorsing the IPPC Guidelines can be found at the USDA.gov web site. Additionally, shipments delivered to DOD distribution facilities or freight consolidation points for eventual delivery to or through EU/IPPC countries shall comply with applicable DLA Regulations and Procurement Letter PROCLTR 02-17.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
SPE7M1-26-U-6971
SECTION B
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
1 PG = 10 EA
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
This item is procured in accordance with a United States Department of Agriculture, Forest Service specification. These Specifications are located at: https://www.fs.usda.gov/t-d/programs/fire/specs.htm
RS067: Shelf life requirement RS001 for a TYPE 2 (CODE X) item with a shelf life of 120 month (extendable) applies to this item.
CRITICAL APPLICATION ITEM
TDP Rev B Gen 2 IAW BASIC DRAWING NR 04024 5100-190C REVISION NR C DTD 12/01/2005 PART PIECE NUMBER:
LINE ITEM 0000000001 TYPE OF COVERAGE: DLA DIRECT, CONUS
SPE7M1-26-U-6971
SECTION B
PR: 1000244916 PRLI: 0001 CONT’D
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 1000244916 0001 PG 2,357.000
This is an estimated quantity and may not be purchased by the IDC.
NSN/MATERIAL:5330002391873
DELIVERY (IN DAYS):0097
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:10 OPI:M INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
QUP ZZZ: See Special Packaging NSN/Part Number: 5330-00-239-1873 Quantity: 2,357 PG Purchase Request: 1000244916QTY: 2357 Delivery: 97 days ADO