HOSE ASSEMBLY, NONME

HOSE ASSEMBLY,NONME
HOSE ASSEMBLY, NONMETALLIC, HIGH PRESSURE
USED ON M809 (DIESEL) SERIES 5 TON 6X6 TRUCKS.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SHELF-LIFE MARKINGS REQUIRED PER 5.2.1 OF MIL-STD-129:
SHELF-LIFEMARKINGS SHALL BE SHOWN AS PART OF THE ITEM IDENTIFICATION
DATA ONUNIT PACKS, INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS, AND
UNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDE THE MANUFACTURED,
CURED, ASSEMBLED OR PACKED DATE (APPLY ONE DATE), AND THE EXPIRATION OR
INSPECT/TEST DATE,
AS APPROPRIATE.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
MANUFACTURERS LIST (QML)" APPLY.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
Shelf-life Additional Requirements
FULL AND OPEN COMPETITION APPLY
DETAILED DRAWING (ONE ITEM)
"CONTRACTOR/MANUFACTURER IS REQUIRED TO ESTABLISH AND MAINTAIN A CALIBRATION SYSTEM THAT MEETS THE REQUIREMENTS OF ANSI/NCSL Z540-1-1994, AMERICAN NATIONAL STANDARD FOR CALIBRATION CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT-GENERAL REQUIREMENTS, OR ISO 10012-1,
SPE7M4-26-T-260W
SECTION B
QUALITY ASSURANCE REQUIREMENTS FOR MEASURING
EQUIPMENTPART 1, METROLOGICAL CONFIRMATION
SYSTEM FOR MEASURING EQUIPMENT."
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
SPECIFICATION
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RS030: Shelf-life requirement RS001 for a TYPE I (CODE W) item with a shelf life of 120 months (non-extendable) applies to this item.
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC SPEC NR MIL-DTL-13531J(4) REVISION NR J DTD 09/16/2022 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 11669207 REVISION NR B DTD 02/05/1992 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7011868108 0001 EA 10.000
NSN/MATERIAL:4720010589490
DELIVERY (IN DAYS):0020
DELIVER FOB: ORIGIN
SPE7M4-26-T-260W
SECTION B
PR: 7011868108 PRLI: 0001 CONT’D
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:AE CLNG/DRY:1 PRESV MAT:00
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:C
UNIT CONT:BV OPI:O
INTRMDTE CONT:DO INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
FREIGHT FORWARDER:
BMO003
V ALEXANDER AND COMPANY INC
22815 GLENN DRIVE SUITE 101
STERLING VA 20164-4497
US
FREIGHT SHIPPING ADDRESS:
BMOA00
ADMINISTRATION FOR NATIONAL DEFENSE
DIRECTION DE RECEPTION ET DE TRANSI
FORCES ARMEES ROYALES MARITIME
CASABLANCA
MA
MARKFOR
BMOA00
ADMINISTRATION FOR NATIONAL DEFENSE
DIRECTION DE RECEPTION ET DE TRANSI
FORCES ARMEES ROYALES MARITIME
CASABLANCA
MA
M/F: (TCN) BMOA5451040018
RDD:
PROJ: TP 2
SUPP ADD: BA3BBS SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 06
DIC: A01 DIST: B07 ADV: 2L FC: YY
Need Ship Date:00/00/0000 Original Required Delivery Date:04/18/2025
SPE7M4-26-T-260W NSN/Part Number: 4720-01-058-9490 Quantity: 10 EA Purchase Request: 7011868108QTY: 10 Delivery: 20 days ADO