Kawasaki Hydraulic Motors

Update 12/14/2021: The purpose of this update is to answer a question. Question: Item A003 does not specify the test data requirements. Is there a specific requirement, or is the "standard" manufacturer's test data sufficient? Answer: The standard manufacturer's report which contains the Original Equipment Manufacturer Acceptance Test Procedure data/reports for each serialized motor is sufficient. Update 12/10/2021: The purpose of this update is to: Correct the Drawing No. in CLIN 0001 from 7443744 Rev. B to 7443747 Rev. B. Upload a revised DD Form 1423-1 Contract Data Requirements List (CDRLs) and a revised Receipt Inspection Report (RIR_QAP_W03844_R1) as attachments. Both of these documents now include a new CDRL, A003, for Test Data. Update the e-mail address of the point of contact for this requirement to: contact@example.gov Extend the closing date to 01/02/2022. This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. The solicitation number is N6660422Q0067. The solicitation is issued as a request for quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through the most current Federal Acquisition Circular. This procurement is being solicited as Unrestricted under NAICS Code 333996, Fluid Power Pump and Motor Manufacturing, as concurred with by the Naval Undersea Warfare Center Division Newport (NUWCDIVNPT) Office of Small Business Programs. The small business size standard is 1,250 employees. NUWCDIVNPT intends to award a Firm Fixed Price (FFP) purchase order for the following items on a brand name basis, as specified in the attached Brand Name Specification; no substitutions allowed. CLIN 0001 KAWASAKI HYDRAULIC MOTOR, MFR P/N HMB030P21PL566, 10 EACH Drawing No. 7443747 Rev. B FFP CLIN 0002 DATA, 1 LOT In Accordance With DD Form 1423-1, Contract Data Requirements List (Not Separately Priced) NOTE: The drawing is labeled Distribution D, which means distribution is authorized to the Department of Defense (DoD) and U.S. DoD contractors with a valid Joint Certification Program (JCP) certification. The drawing is uploaded to SAM.gov as an attachment with access restricted to JCP-certified companies only. Only potential offerors with an active registration in JCP will be able to access the drawing. Please visit https://www.dlis.dla.mil/jcp/ for further details on the program and registration. Delivery is FOB Destination to Newport, RI 02841. The following FAR and DFARS provisions and clauses apply to this solicitation. 52.204-24, Representation Regarding Certain Telecommunications and Video Surveillance Services or Equipment; 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment; 52.212-1, Instructions to Offerors-Commercial Items; 52.212-3, Offeror Representations and Certifications-Commercial Items; 52.212-4, Contract Terms and Conditions-Commercial Items; 52.212-5, Contract Terms and Conditions Required To Implement Statutes or Executive Orders-Commercial Items; 252.204-7008, Compliance with Safeguarding Covered Defense Information Controls; and 252.204-7015, Notice of Authorized Disclosure of Information for Litigation Support. Additional contract requirement(s) or terms and conditions: In accordance with DFARS Clause 252.211-7003, the contractor shall provide a unique item identifier (UID) for all delivered items for which the Government's unit acquisition cost is $5,000.00 or more. The Government's preferred payment method is via the Government Purchase Card (GPC), if the contractor accepts the GPC. If the GPC is not used, payment will be made via the Wide Area Workflow (WAWF). If UID applies, payment must be made via WAWF and the UID is entered into WAWF. The full text of incorporated FAR/DFARS provisions and clauses is available at: www.acquisition.gov This requirement will be awarded to the offeror with the lowest price technically acceptable (LPTA) quote. In order to be determined technically acceptable, the offeror must quote the Brand Name items required by this solicitation (no substitutions allowed) in the specified quantities. Offerors must be an authorized distributor of Kawasaki Precision Machinery. The Government will consider past performance information in accordance with DFARS Provision 252.213-7000 where negative information within SPRS may render a quote being deemed technically unacceptable. Offerors must be actively registered in the System for Award Management (SAM) (https://www.sam.gov) to be eligible for award. Instructions for registration are available on the SAM website. Quotes shall include: Company Name Company Point of Contact, including name, telephone number, and e-mail address CAGE Code (from http://www.sam.gov registration). Quotes shall be submitted via e-mail to Carrie Rochelle at contact@example.gov. Quotes are due by 5 PM Eastern Standard Time on January 2, 2022. Quotes received after this date/time will be considered late and may not be considered for award.