LENS, LIGHT

LENS,LIGHT
LENS,LIGHT
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
80020 NAVAL AIR WARFARE CENTER
IDENTIFY TO:
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT
DLA DURING "OPEN SOLICITATION ONLY".
TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)>
FOR EBS SOLICITATIONS USE URL
HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CRITICAL ITEM SOURCE INSPECTION REQUIRED.
THIS MATERIAL MUST MEET NAVAIR AIRCRAFT LAUNCH &
RECOVERY EQUIPMENT TRACEABILITY REQUIREMENTS. BARE
SPE8E7-27-T-0177
SECTION B
ITEM MARKINGS SHALL BE IAW THE TECHNICAL DATA
DRAWINGS PROVIDED.
BARE ITEM MATERIAL SHALL BE MARKED WITH CONTRACT
NUMBER, NAWC CAGE, AND PART NUMBER UNLESS OTHERWISE
SPECIFICIED ON ASSOCIATED DRAWING. IF A CONFLICT
EXISTS WITH MARKING REQUIREMENTS OF THIS 82N ALRE/SE
ITEM, THE ASSOCIATED DRAWING REQUIREMENTS SHALL APPLY.
TDP Rev A Gen 1 IAW BASIC DRAWING NR 80020 425981 REVISION NR C DTD 09/18/2001 PART PIECE NUMBER: P/N: 425981-1
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018730128 0001 EA 51.000
NSN/MATERIAL:6220013164619
DELIVERY (IN DAYS):0167
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA-QUP:001
IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313,
PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025.
IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH
FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE
WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3218
DLA DISTRIBUTION SAN DIEGO
3581 CUMMINGS ROAD BLDG 3581
SAN DIEGO CA 92136-3581
US
SPE8E7-27-T-0177
SECTION B
PR: 7018730128 PRLI: 0001 CONT’D
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3218
DLA DISTRIBUTION SAN DIEGO
3581 CUMMINGS ROAD BLDG 3581
SAN DIEGO CA 92136-3581
US
Need Ship Date:04/12/2027 Original Required Delivery Date:05/09/2027
SPE8E7-27-T-0177 NSN/Part Number: 6220-01-316-4619 Quantity: 51 EA Purchase Request: 7018730128QTY: 51 Delivery: 167 days ADO