RESISTOR, FIXED, FILM

RESISTOR,FIXED,FILM
RESISTOR,FIXED,FILM
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
THIS NSN IS LISTED AS A PRIMARY QPL OR QML THEREFORE
THE QUALIFIED PRODUCTS LIST OR QUALIFIED MANUFACTURERS
LIST IS APPLICABLE.
UNIT PACKAGE MARKING REQUIREMENT FOR COMPONENT LEAD FINISH
(a) In addition to all other marking requirements in this contract, the Contractor shall apply one of the assigned markings in accordance with paragraphs 5.3.1 and 5.3.2 of IPC/JEDEC J-STD-609, Marking and Labeling of Components, printed circuit boards (PCBs) and printed circuit board assemblies (PCBAs) to Identify Lead (Pb), Pb-Free and Other Attributes, to each individual unit pack of the item being acquired. Placement of the markings shall be in accordance with paragraph 6.2 of the standard.
(b) Copies of the current version of this standard may be purchased or downloaded from the Association Connecting Electronics Industry (IPC), http://www.ipc.org, http://www.ipc.org, or the Solid State Technology Association (JEDEC), http://www.jedec.org. http://www.jedec.org.
THE USE OF ANY CLASS I OZONE-DEPLETING SUBSTANCE (ODS) IN THE DESIGN, MANUFACTURING, TESTING, CLEANING, OR ANY OTHER PROCESS FOR THIS ITEM UNDER ANY MILITARY OR FEDERAL SPECIFICATION, STANDARD OR DRAWING REFERENCED IN THIS ITEM DESCRIPTION IS "PROHIBITED" UNLESS THE SEPARATE WRITTEN APPROVAL OF THE CONTRACTING OFFICER IS OBTAINED. THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT PERFORMANCE REQUIREMENTS. THIS DOES NOT APPLY TO COMMERCIAL ITEMS, AS DEFINED IN "FAR 11.001" OR TO PART-NUMBEREDONLY ITEMS.
TDP Rev A Gen 1 IAW BASIC SPEC NR MIL-PRF-55182/10F(1) REVISION NR F DTD 08/15/2024 PART PIECE NUMBER: RNR75E4221BM
TDP Rev A Gen 1
SPE7M5-26-T-474Z
SECTION B
IAW REFERENCE SPEC NR MIL-PRF-55182K(1) SUP 1
REVISION NR K DTD 08/15/2024
PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018273000 0001 EA 12.000
NSN/MATERIAL:5905000603720
DELIVERY (IN DAYS):0168
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:GX CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:LT CUSH/DUNN THKNESS:A
UNIT CONT:B9 OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:100
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
ESD and PHYSICAL protection are required for contacts, leads, terminals, and other protrusions by means of container design, cushioning, and/or other ESD protective devices. Components with pins or leads shall have adequate cushioning to PREVENT DAMAGE, BREAKAGE and/or BENDING OF LEADS when not specified in the packaging codes.
This item requires DOD QUALIFIED Electrostatic Discharge (ESD) and/or Electromagnetic Interference (EMI) protective packaging materials in accordance with MIL-PRF-81705. All items subject to degradation from ESD/EMI environmental field forces shall be handled and packaged at an approved field force protective work station.
For ESD protection MIL-PRF-81705, Type I (MIL-DTL-117, Type I, Class F, Style 1) converted bag barrier material shall be used along with MIL-PRF-81705, Type III (MIL-DTL-117 Type II, Class H, Style 2) barrier material wrap if the contract doesn't specifically require ESD approved cushioning.
For EMI protection MIL-PRF-81705, Type I (MIL-DTL-117, Type I, Class F, Style 1) converted bag barrier material shall be used.
The supplier shall be responsible for verifying that all MIL-PRF-81705 barrier materials (or converted bags) were supplied from a qualified manufacturer currently listed on QPL-81705.
SPE7M5-26-T-474Z
SECTION B
PR: 7018273000 PRLI: 0001 CONT’D
For additional ESD/EMI packaging information, refer to the following DLA packaging website: https://www.dla.mil/HQ/LogisticsOperations/Packaging/PackFAQs/ESDS/
If the preservation method code in the solicitation does not specify ESD/EMI protection and the Offeror's proposed item of supply is subject to degradation from ESD/EMI environmental field forces, Offerors shall provide appropriate technical packaging data with their proposals.
ZZ ADDITIONAL SPECIAL MARKING: 39 ESD sensitive electronic device requirements of MIL-STD-129 apply
UNIT PACKAGE MARKING REQUIREMENT FOR COMPONENT LEAD FINISH
(a) In addition to all other marking requirements in this contract, the Contractor shall apply one of the assigned markings in accordance with paragraphs 5.3.1 and 5.3.2 of IPC/JEDEC J-STD-609, Marking and Labeling of Components, printed circuit boards (PCBs) and printed circuit board assemblies (PCBAs) to Identify Lead (Pb), Pb-Free and Other Attributes, to each individual unit pack of the item being acquired. Placement of the markings shall be in accordance with paragraph 6.2 of the standard.
(b) Copies of the current version of this standard may be purchased or downloaded from the Association Connecting Electronics Industry (IPC), http://www.ipc.org, http://www.ipc.org, or the Solid State Technology Association (JEDEC), http://www.jedec.org. http://www.jedec.org.
PARCEL POST ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN RD
REC WHSE 57
TRACY CA 95304-5000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN ROAD
25600 S CHRISMAN RD REC WHSE 57
TRACY CA 95304-5000
US
Need Ship Date:03/09/2027 Original Required Delivery Date:04/06/2028
SPE7M5-26-T-474Z NSN/Part Number: 5905-00-060-3720 Quantity: 12 EA Purchase Request: 7018273000QTY: 12 Delivery: 168 days ADO