Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, September 16 at 2:00 PM EDT

Register Free →

This Solicitation opportunity from National Aeronautics And Space Administration was posted on June 2, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.

Rocket Motor ICP Pressure Sensor 10k psi 0.5 mV/psi He Bleed, H2O cooled

Closed
80NSSC26934593QFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

Active Opportunities Like This One

AI Contract Overview

Show more

NASA Shared Services Center is seeking to procure 40 Model 123B23 Rocket Motor ICP Pressure Sensors rated for 10,000 psi with a output sensitivity of 0.5 mV/psi, equipped with helium bleed and water-cooling, along with 80 brass seals measuring 0.624-inch OD by 0.553-inch ID by 0.080-inch thickness, under a sole source contract to PCB PIEZOTRONICS, INC. The acquisition is being conducted under FAR Part 12 as a commercial item procurement, with FAR 12.102(a) cited as the authority for sole source selection due to the determination that PCB PIEZOTRONICS, INC is the exclusive provider of this highly specialized sensor. The sensors must meet rigorous environmental and performance criteria including survival in methane and oxygen combustion environments, withstand peak pressures up to 15,000 psi and flash temperatures exceeding 6,000 degrees Fahrenheit, operate within a temperature range of -100 to 250 degrees Fahrenheit, and feature hermetic sealing, ceramic-coated tips, electrical ground isolation, low-impedance output, and specific excitation and current draw parameters. Performance is to be delivered to Marshall Space Flight Center in Huntsville, Alabama, with delivery scheduled in batches of ten units within 20 weeks for the first ten units and the remaining thirty units delivered within 40 weeks, while the brass seals may be shipped as ready. The procuring center is located at Stennis Space Center, Mississippi, with Cody Guidry as the primary point of contact and Shari Trigg as the contracting officer. This action is in the sources sought phase, with responses due by 3:00 p.m. Central Standard Time on June 4, 2026, and submissions must be in writing; oral communications are prohibited. The procurement is subject to the NASA FAR Supplement Clause 1852.215-84 Ombudsman provision, and the NAICS code assigned is 334516. No contract value or pricing data is provided, and no inspection or acceptance criteria are detailed in the available documentation.

General Info

NASA seeks sole source ICP Pressure Sensor, 10,000 psi, 0.5 mV/psi, from PCB PIEZOTRONICS.

Agency

National Aeronautics And Space Administration → NASA Shared Services CenterView Agency

Contract Value

$199,180

NAICS

334516 - Analytical Laboratory Instrument ManufacturingView NAICS

Place of Performance

MS

Set-Aside

NONE

Awardee

PCB PIEZOTRONICS, INC.View Profile

Award Issued Date

Documents

(1)

SATPC0041275+TAB+07+SOW+Redacted.pdf

PDF

AI Contract Breakdown

Uniform Contract Format

Sign up to view the full breakdown with detailed analysis of each section.

Timeline

PhaseClosed
Posted

Solicitation

Response Deadline

Deadline has passed

Submission Closed

Find active opportunities like this

Start your free trial to discover similar active contracts, track opportunities, and build proposals with AI assistance.

Organization & Contact Information

Show more
AgencyNational Aeronautics And Space Administration → NASA Shared Services Center
Contacts2 people available
OfficeSTENNIS SPACE CENTER, MS, 39529, USA
Organization / Agency
National Aeronautics And Space Administration → NASA Shared Services Center
View Agency Profile
Office AddressSTENNIS SPACE CENTER, MS, 39529, USA
Contacts

Full Description

Show more

Synopsis:



NASA/NSSC has a requirement for Rocket Motor ICP Pressure Sensor 10k psi 0.5 mV/psi He Bleed, H2O cooled. 


NASA/NSSC intends to issue a sole source contract to PCB PIEZOTRONICS, INC: 3425 WALDEN AVE | DEPEW, NEW YORK 14043 under the authority of FAR 12.102(a). It has been determined that PCB PIEZOTRONICS, INC is the sole provider of Rocket Motor ICP Pressure Sensor 10k psi 0.5 mV/psi He Bleed, H2O cooled.


NASA/NSSC will be the procuring center for this effort. Performance will be located at NASA/ Marshall Space Flight Center (MSFC).


The Government intends to acquire Commercial items or services using the provisions, clauses and procedures prescribed in FAR Part 12 for Commercial



The NAICS Code for this procurement is 334516.



Interested organizations may submit their capabilities and qualifications to perform the effort in writing to the identified point of contact not later than 3:00 p.m. Central Standard Time on 6/4/2026. Such capabilities/qualifications will be evaluated solely for the purpose of determining whether or not to conduct this procurement on a competitive basis. A determination by the Government not to compete this proposed effort on a full and open competition basis, based upon responses to this notice, is solely within the discretion of the government.



Oral communications are not acceptable in response to this notice.



NASA FAR Supplement Clause 1852.215-84, Ombudsman, is applicable. The Center Ombudsman for this acquisition can be found at https://www.hq.nasa.gov/office/procurement/regs/Procurement-Ombuds-Comp-Advocate-Listing.pdf .



Primary Point of Contact:


Cody Guidry


Procurement Specialist II


Cody.d.guidry@nasa.gov




Secondary Point of Contact:


Shari Trigg


Contracting Officer


Shari.trigg@nasa.gov


More opportunities from National Aeronautics And Space Administration → NASA Shared Services Center

Same awarding agency

NAICS: 333998
New
Federal
Lower Wing / Elevon Heater Carriages
Solicitation # 80NSSC26937774Q-1
NASA Shared Services Center is soliciting quotes under solicitation 80NSSC26937774Q for the fabrication and delivery of Lower Wing and Elevon Heater Carriage test hardware for the NASA Armstrong Flight Research Center. This firm-fixed-price contract is set aside for small businesses under NAICS code 333998. The scope involves the production of various components, including heater frames, adapter plates, bearing brackets, and axis rods, all of which must be fabricated according to government-furnished design drawings. The target delivery schedule is within 12 weeks of contract award, with a preference for earlier completion. Deliveries are FOB Destination to Edwards, California, and the contractor is required to provide status updates every three weeks. Award will be based on the best value, evaluating price, fabrication duration, technical acceptability, and past performance, with a requirement for three references from the last three years. The contractor must provide a manufacturing process plan and perform dimensional tolerance inspections. Due to the nature of the hardware, strict compliance with U.S. export control laws, including ITAR and EAR, is mandatory. Additionally, the contractor must be registered in the System for Award Management and provide a Cage Code or Unique Entity ID. All contractual inquiries are directed to Tracy Bremer.
All Other Miscellaneous General Purpose Machinery Manufacturing

POSTED

2 days ago

DEADLINE

in 4 days
View Details
NAICS: 811210
New
Federal
2026 Service contract for D8 Discover DaVinci
Solicitation # 80NSSC26942313Q
The NASA Shared Services Center is seeking a service contract for the maintenance of the D8 Discover DaVinci XRD instrument located at the NASA Glenn Research Center. The requirement covers the period of performance from September 10, 2026, to September 9, 2027. Under the authority of FAR 12.102(a), NASA intends to issue a sole source contract to Bruker AXS LLC, as they have been determined to be the sole provider capable of performing these services. The procurement falls under NAICS code 811210 and follows the procedures prescribed in FAR Part 12 for commercial items and services. The scope of work includes both emergency and scheduled maintenance to preserve the original equipment performance of the instrument. All services must be performed by factory-trained service engineers and conducted according to manufacturer instructions, including the verification of radiation safety. The contract provides for unlimited emergency service visits and technical phone support during regular business hours, with a required emergency response time of 48 hours for breakdowns that render the instrument inoperable. While this notice allows interested organizations to submit capabilities and qualifications by September 15, 2026, to determine if the procurement should be competitive, the government explicitly states that price quotes submitted in response to this notice will not be reviewed or accepted.
Electronic and Precision Equipment Repair and Maintenance

POSTED

2 days ago

DEADLINE

in 3 days
View Details

Find Active Opportunities Like This

Get AI-powered intelligence on the opportunities still open

Every page of the solicitation package shredded into a compliance breakdown

AI-powered matching based on your capabilities and past performance

Competitor and incumbent history on the requirement

Automated alerts on amendments, Q&A deadlines, and award

Miguel
Hillary
Keith Deutsch
Christine

Join 650+ contractors already using CLEATUS