This Solicitation opportunity from Department Of Defense was posted on May 11, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, CAP, HEXAGON H
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract pertains to the procurement of a hexagon head cap screw, specifically part number 50034574, which conforms to ISO 10642-M5x12-A4-70 standards with a blackening treatment for corrosion protection per MIL-DTL-13924 rev. D, class 3 or 4. It is classified as a commercial off-the-shelf (COTS) item with an AMSC code “Z.” The specified quantity is one each, with a delivery requirement of 10 days FOB origin, and inspection and acceptance conducted at the destination. Packaging and marking must comply with MIL-STD-129 and MIL-STD-2073-1E requirements, including DLA packaging protocols and no special markings. Sampling will be conducted in accordance with MIL-STD-1916 or an equivalent zero-defect plan. The contract is issued by the Department of Defense’s ASC Commodities Division with the place of performance in Sumner, Washington. The primary point of contact is Monica Greene, reachable via email and phone for any procurement coordination. Shipments are to be made by traceable express means, avoiding parcel post, to the designated Sumner distribution center. The solicitation was posted on May 11, 2026, with a response deadline of May 19, 2026, under solicitation number SPE4A6-26-T-51A5. This contract ensures all technical, quality, and packaging requirements are fully incorporated as per DLA master lists and applicable military standards.
General Info
Agency
NAICS
Place of Performance
3700 150TH AVE CT EAST, SUMNER, WA, 98390-0000, USSet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW,CAP,HEXAGON
ESA Response: The part 50034574 being referenced, pertains to ISO 10642-M5x12-A4-70 Blackening, with blackening per MIL-DTL-13924 rev. D, class 3 or 4 to be applied for corrosion protection.
As this is a COTS item, the AMSC code should be “Z”.
All information necessary for procurement of this item is provided herein.
ESA Full Name: Christopher J. Stetz Email: christopher.j.stetz.civ@army.mil Postal Address: Armaments Center WSEC WEAPON SYSTEMS & TECHNOLOGY
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
THIS ITEM IS IDENTIFIED AS A COMMERCIAL OFF THE SHELF (COTS) ITEM
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
KONGSBERG DEFENCE & AEROSPACE AS N0013 P/N 50034574
SPE4A6-26-T-51A5
SECTION B
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7016676231 0001 EA 1.000
NSN/MATERIAL:5305251611493
DELIVERY (IN DAYS):0010
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:31 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:BL OPI:M
INTRMDTE CONT:ED INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
BULK BREAK POINT:
W5872U
W6DX PEO GCS WARREN
SUMNER DISTRIBUTION CENTER
3700 150TH AVE CT EAST
SUMNER WA 98390-0000
US
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W5872U
W6DX PEO GCS WARREN
SUMNER DISTRIBUTION CENTER
3700 150TH AVE CT EAST
SUMNER WA 98390-0000
US
MARKFOR
W5872U
SPE4A6-26-T-51A5
SECTION B
PR: 7016676231 PRLI: 0001 CONT’D
W6DX PEO GCS WARREN
SUMNER DISTRIBUTION CENTER
3700 150TH AVE CT EAST
SUMNER WA 98390-0000
US
M/F: (TCN) W9095360229026
RDD: N
PROJ: G6D TP 2
SUPP ADD: W5872U SIG: J
FOR GOVERNMENT USE ONLY: (IPD) 05
DIC: A0A DIST: ADV: FC: W5
Need Ship Date:00/00/0000 Original Required Delivery Date:01/28/2026
SPE4A6-26-T-51A5 NSN/Part Number: 5305-25-161-1493 Quantity: 1 EA Purchase Request: 7016676231QTY: 1 Delivery: 10 days ADO