SCREW, CAP, SOCKET HEAD

SCREW,CAP,SOCKET HEAD
SCREW, CAP, SOCKET HEAD
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT
DLA DURING "OPEN SOLICITATION ONLY".
TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)>
FOR EBS SOLICITATIONS USE URL
HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPE4A6-26-T-11GB
SECTION B
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
ITEMS SUPPLIED UNDER THIS NSN SHALL MEET ALL REQUIRED ASPECTS OF
MIL-DTL-1222J, INCLUDING BUT NOT LIMITED TO: MANUFACTURING PROCESSES,
MECHANICAL PROPERTIES, MARKINGS, INSPECTIONS AND EVALUATIONS ACQUISITION
REQUIREMENTS: DOCUMENT: MIL-DTL-1222J, 08 DECEMBER 2000, GENERAL
SPECIFICATION FOR STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A
HIGH DEGREE OF RELIABILITY IS REQUIRED ITEM CONFIGURATION: PART NUMBER
M1222SN8C218NCLN PER APPENDIX OF MIL-DTL-1222J; TYPE II SOCKET HEAD CAP
SCREW, 1/2-13 UNC 2A, 1.125 INCH NOMINAL LENGTH OVERALL; DIMENSIONS
SHALL BE IN ACCORDANCE WITH ASME B18.3 SELF-LOCKING ELEMENT: SHALL BE
TYPE L IN ACCORDANCE WITH MIL-DTL-18240F Material shall be NICUAL (GR-500) per QQ-N-286 Rev G or later. Material properties shall be per table II of MIL-DTL-1222. Material properties shall be substantiated by original (mill) certifications reports of mechanical properties and chemical composition traceable to material by heat or lot numbers and must include results of slow strain rate tensile tests from an approved laboratory as listed below: Huntington Alloys Metallurgical Consultants, Inc. Naval Surface Warfare Center, Carderock Division Teledyne Allvac Mannesmann Rohrenworke Westmoreland Mechanical Research and Testing Material property, chemical composition and slow strain test results shall be provided for each heat/lot of material used to manufacture the fasteners Verification of conformance shall be in accordance with paragraph 4 of MIL-DTL-1222 with the exception that each fastener shall be liquid penetrant inspected in accordance with the provisions of paragraph 4.3.3.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
CRITICAL APPLICATION ITEM
TDP Rev B Gen 2 IAW BASIC SPEC NR MIL-DTL-1222J REVISION NR J DTD 12/08/2000 PART PIECE NUMBER: M1222SN8C218NCLN
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 53711 T9074-AS-GIB-010/271 REVISION NR 1 DTD 09/11/2014 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE SPEC NR MIL-DTL-18240F(1) NOT 1 REVISION NR F DTD 09/04/2019 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE NON GOVT STD ASME B18.3-2012 REVISION NR DTD 01/01/2012 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE NON GOVT STD QQ-N-286G REVISION NR G DTD 12/07/2000 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to
SPE4A6-26-T-11GB
SECTION B
PR: 7017659176 PRLI: 0001 CONT’D
determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017659176 0001 EA 1.000
NSN/MATERIAL:5305014919371
DELIVERY (IN DAYS):0020
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:10 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PARCEL POST ADDRESS:
N27157
USS HYMAN G RICKOVER (SSN 795)
73 EASTERN POINT RD
ATTN: SSN 795
GROTON CT 06340-4905
US
RDD 777 SHIPMENT. SHIP BY FASTEST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
N27157
USS HYMAN G RICKOVER (SSN 795)
DLA VENDORS: USE VSM FOR
US
M/F: (TCN) N2715761961188
RDD: 777
PROJ: ZH9 TP 2
SUPP ADD: N48096 SIG: C
SPE4A6-26-T-11GB
SECTION B
PR: 7017659176 PRLI: 0001 CONT’D
FOR GOVERNMENT USE ONLY: (IPD) 06
DIC: A4A DIST: V9B ADV: 2A FC: VO
Need Ship Date:00/00/0000 Original Required Delivery Date:07/27/2026
SPE4A6-26-T-11GB NSN/Part Number: 5305-01-491-9371 Quantity: 1 EA Purchase Request: 7017659176QTY: 1 Delivery: 20 days ADO