This Solicitation opportunity from Department Of Defense was posted on May 18, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, CLOSE TOLERAN
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract solicitation SPE4A6-26-T-59W9 seeks the procurement of 288 precision close tolerance screws identified by NSN 5305-01-231-2206, with delivery required to Tracy, California within 165 days after award. The item must comply with technical and quality specifications referenced in the DLA Master List of Technical and Quality Requirements, including R-numbered requirements for configuration, inspection, and performance. Sampling procedures must follow MIL-STD-1916 or ASQ H1331 Table 1, or another zero-based sampling plan, with verification levels of VII, IV, and II assigned to critical, major, and minor attributes respectively, corresponding to AQLs of 0.1, 1.0, and 4.0. Acceptance is to occur at the destination, with the contractor responsible for ensuring compliance with all applicable inspection and quality standards. Packaging and labeling must adhere to MIL-STD-129 and DLA-specific packaging requirements RP001, including bare item marking per RQ017 and proper unit of issue and quantity per unit pack. The screws are subject to export control under ITAR or EAR, requiring contractors to be approved by DLA under the US/Canada Joint Certification Program, have completed required export control training, and comply with DFARS 252.225-7048. The contractor must hold CMMC Level 2 certification as a certified third-party assessment organization, and is subject to DFARS 252.204-7012 for safeguarding covered defense information and reporting cyber incidents. All hazardous materials must be labeled per OSHA’s Hazard Communication Standard and MIL-STD-129, with Safety Data Sheets required for submission prior to award. Invoicing must be performed electronically through WAWF, and the delivery point is W1A8 DLA DIST SAN JOAQUIN in Tracy, CA. The solicitation is subject to FAR and DFARS clauses, including those on small business representation, equal opportunity, accelerated payments, and unenforceability of unauthorized obligations, and requires submission via the DIBBS portal by May 26, 2026. No pricing information is provided in the solicitation, and no evaluation factors or contract value are explicitly stated.
General Info
Place of Performance
REC WHSE 57, TRACY, CA, 95304-5000, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW<(>,<)> CLOSE TOLERANCE
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RT001: MEASURING AND TEST EQUIPMENT
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire
SPE4A6-26-T-59W9
SECTION B
(both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 5305-01-231-2206 Quantity: 288 EA Purchase Request: 7016752878QTY: 288 Delivery: 165 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Earlier notices in this NAICS code
Posted before this notice, open and closed
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 750+ contractors already using CLEATUS