SCREW, CLOSE TOLERANCE

SCREW,CLOSE TOLERANCE
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
SCREW, CLOSE TOLERANCE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RD002, COVERED DEFENSE INFORMATION APPLIES
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CRITICAL ITEM SOURCE INSPECTION REQUIRED.
SOURCE INSPECTION REQUIRED.
DATA IS PROPRIETARY OR INSUFFICIENT FOR
COMPETITIVE PROCUREMENT
FAR 52.246-11, HIGHER LEVEL CONTRACT QUALITY
REQUIREMENTS, APPLIES/ISO 9001/ANSI/ASQC
Q 9001 APPLIES.
QAP EQ003 APPLIES
SAMPLING:
SIKORSKY CORPORATION, CAGE 78286 ALTERNATE SAMPLING PLAN QAP 1201
PROCEDURE, "ATTRIBUTE SINGLE STATISTICAL ACCEPTANCE SAMPLING" IS
ACCEPTABLE. SIKORSKY CORPORATION'S ALTERNATE PLAN MUST MEET OR EXCEED
THE REQUIREMENTS OF ASQ H1331 OR MIL-STD-1916.
SPE4A6-27-T-6993
SECTION B
DSCR DOES NOT CURRENTLY HAVE AN APPROVED
TECHNICAL DATA PACKAGE AVAILABLE FOR THIS NSN.
DATA IS PROPRIETARY OR INSUFFICIENT FOR
COMPETITIVE PROCUREMENT.
ACQUISITION OF THIS PART IS RESTRICTED TO THE SOURCE(S) SPECIFIED ON THE
SOURCE CONTROL DRAWING. ALTERNATE OFFERS WILL NOT BE ACCEPTED. USE
PROCUREMENT NOTE L22.
52.246-11 Higher-Level Contract Quality Requirement (Feb 1999) ANSI/ISO/ASQ Q9001-2015(excluding para 7.3) or equivalent. Certification or registration of a contractor's quality system or program is not required by DoD if ISO or ANSI/ASQ standards are used.
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
Casting/forging may be required to manufacture this NSN and tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains contact@example.gov.
REFER TO ALL CAUTION STATEMENTS REFER TO ALL GENERAL AND ENGINEERING NOTES
CRITICAL APPLICATION ITEM
HOWMET GLOBAL FASTENING SYSTEMS INC 06950 P/N 3M123-3-6 HUCK INTERNATIONAL, INC 17446 P/N 3M123-3-6 SPS TECHNOLOGIES, LLC 56878 P/N 3M123-3-6 FASTENER INNOVATION TECHNOLOGY, INC. 58998 P/N 3M123-3-6 HI-SHEAR CORPORATION 73197 P/N 3M123-3-6 LISI AEROSPACE CANADA CORP DIV HI L4528 P/N 3M123-3-6
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 76301 3M123 REVISION NR U DTD 09/09/1997 PART PIECE NUMBER: 3M123-3-6
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017740441 0001 EA 2,637.000
NSN/MATERIAL:5305000175131
DELIVERY (IN DAYS):0103
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
SPE4A6-27-T-6993
SECTION B
PR: 7017740441 PRLI: 0001 CONT’D
PREP FOR DELIVERY:
PKGING DATA-QUP:025
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET
BLDG 376
ROBINS A F B GA 31098-1887
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET BLDG 376
ROBINS A F B GA 31098-1887
US
Need Ship Date:08/04/2026 Original Required Delivery Date:01/13/2027
SPE4A6-27-T-6993 NSN/Part Number: 5305-00-017-5131 Quantity: 2,637 EA Purchase Request: 7017740441QTY: 2637 Delivery: 103 days ADO