Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, July 22 at 2:00 PM EDT

Register Free →
logo
Get CLEATUSFree Trial

SCREW, MACHINE

Active
SPE4A6-26-T-08SQFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

Show more

This contract is for the procurement of 184 machine screws identified by NSN 5305-01-555-8107 and part number MS35206-267Z, classified as a commercial item. The technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, incorporating specific standards such as RQ011 for removal of government identification from non-accepted supplies, RQ017 for bare item marking, and RQ042 mandating ISO 9001:2015 compliance for both manufacturers and non-manufacturers. Mercury and mercury-containing compounds are strictly prohibited unless used functionally in batteries, fluorescent lights, instruments, sensors, controls, weapon systems, or chemical reagents specified by NAVSEA, with portable mercury-containing devices requiring shockproof design and secondary containment. Sampling must follow MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required unless otherwise specified, and attributes are assigned verification levels of VII, IV, and II for critical, major, and minor characteristics respectively. Packaging and labeling must comply with MIL-STD-129 and ASTM D3951, with DLA’s master requirements taking precedence. Palletization must adhere to RP001, and the unit of issue is each (EA) with no variance allowed in quantity. Delivery is FOB origin with inspection and acceptance occurring at the destination, and the required delivery date is March 1, 2027, with a need ship date of January 17, 2027. The item is not subject to shelf life restrictions. The contract references applicable standards including NASM35206 Rev 4 and FF-S-92E Rev E and requires compliance with DLA’s packaging and transportation directives, including DLA Proc Notes C19 and C20. The delivery address is the DLA Distribution facility in New Cumberland, PA, and the solicitation, issued under SPE4A6-26-T-08SQ, was posted on July 21, 2026, with a response deadline of July 29, 2026, under NAICS code 332722. Item Unique Identification is not required per DFARS 252.211-7003(c)(1)(i), and covered

General Info

184 machine screws, NSN 5305-01-555-8107, ISO 9001:2015, FOB origin, deliver to New Cumberland, PA by March 1, 2027

Agency

Department Of Defense → ASC COMMODITIES DIVISIONView Agency

NAICS

332722 - Bolt, Nut, Screw, Rivet, and Washer ManufacturingView NAICS

Place of Performance

2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, US

Set-Aside

NONE

Documents

(0)

No documents available

AI Contract Breakdown

Uniform Contract Format

No contract breakdown available.

Cannot generate Contract Breakdown because no documents were found from this contract's source.

Timeline

PhaseSolicitation
Posted

Solicitation

Response Deadline

Submission deadline

Response Deadline

Ready to pursue this opportunity?

Start your free trial to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC COMMODITIES DIVISION
Contacts1 person available
OfficeUS
Organization / Agency
Department Of Defense → ASC COMMODITIES DIVISION
View Agency Profile
Office AddressUS
Contacts
Ashley JONES-TURNER
contact@example.gov
+1 (555) 000-0000

Full Description

Show more
SCREW,MACHINE
SCREW<(>,<)> MACHINE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
SPE4A6-26-T-08SQ
SECTION B
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RQ042: Non-Tailored Higher-Level Quality Requirements (ISO 9001:2015) for Manufacturers and Non-Manufacturers
THIS MATERIAL DOES NOT HAVE A SHELF LIFE REQUIREMENT
TDP Rev B Gen 2 IAW BASIC NON GOVT STD NASM35206 REVISION NR 4 DTD 04/30/2019 PART PIECE NUMBER: MS35206-267Z
TDP Rev B Gen 2 IAW REFERENCE UNK FF-S-92E(1) REVISION NR E DTD 05/05/2025 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017571619 0001 EA 184.000
NSN/MATERIAL:5305015558107
DELIVERY (IN DAYS):0171
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA-QUP:001
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
W25G1U
SPE4A6-26-T-08SQ
SECTION B
PR: 7017571619 PRLI: 0001 CONT’D
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:01/17/2027 Original Required Delivery Date:03/01/2027
SPE4A6-26-T-08SQ NSN/Part Number: 5305-01-555-8107 Quantity: 184 EA Purchase Request: 7017571619QTY: 184 Delivery: 171 days ADO

Similar Contracts

Same NAICS industry code

NAICS: 332722
New
DIBBS
NUT, IMPELLER, LEFT HANDThe contract specifies the procurement of two left-hand impeller nuts, identified by NSN 5310-01-424-5905 and part number 15-0125-01, manufactured by Buffalo Pumps Inc. and supplied under solicitation SPE4A6-26-T-08ST. The item is classified as a critical application component and must comply with stringent technical and quality requirements referenced from the DLA Master List, including packaging standards per MIL-STD-2073-1E and marking per MIL-STD-129. Sampling follows MIL-STD-1916 or equivalent zero-based plans with strict acceptance criteria: critical attributes require zero non-conformances, and unspecified attributes are treated as major. Mercury and mercury-containing compounds are strictly prohibited in the item, its preservation, packaging, or marking, except for specified functional uses in instrumentation or batteries, which must include secondary containment per NAVSEA 5100-003D. Preservation is to be conducted in accordance with ASTM D3951 using preservation method code 10. Delivery is FOB origin with no quantity variance allowed, and inspection and acceptance occur at the destination warehouse in Tracy, California. The delivery window is 171 days from contract award, with a required ship date of January 17, 2027, and the original delivery deadline was October 30, 2026. All logistics and transportation protocols follow DLA procedural notes C19 and C20, and the unit of issue is each (EA) at a unit price of $2.00, totaling $4.00.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
SCREW ASSEMBLY, PANELThe contract pertains to the procurement of a screw assembly for panel use with NSN 5305015234800 and part number 114108-.500-SS-SDS-12, sourced from Accurate Screw Machine Corp. A total of 23 units are required under purchase request 7017571666, with delivery mandated within 171 days from the contract award, to be shipped FOB origin to the designated receiving warehouse in Tracy, California. The supply is subject to strict packaging standards per ASTM D3951 and MIL-STD-129, with palletization conforming to DLA packaging requirements, and all packaging must be properly marked and labeled. Inspection and acceptance occur at the destination, with no variance permitted in quantity. Technical and quality requirements referenced through R and I numbers are governed by the DLA Master List of Technical and Quality Requirements, which supersedes all other specifications. Sampling procedures must comply with MIL-STD-1916 or ASQ H1331 Table 1 using zero-defect acceptance criteria unless otherwise specified, with attribute classification and verification levels strictly enforced. The item is classified as proprietary with insufficient technical data for competitive procurement, and covered defense information protocols apply. The unit of issue is each, and transportation logistics follow DLA procedural notes C19 and C20. The solicitation was issued on July 21, 2026, with responses due by July 29, 2026, under contract number SPE4A6-26-T-08DZ.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
WASHER, CONCAVEThe item is a concave washer with NSN 5310-01-654-9319, with a quantity of 40 units required under purchase request 7017522998, and must be delivered within five days of order award. The solicitation is issued under contract number SPE4A6-26-T-08QN, posted on July 21, 2026, with responses due by July 29, 2026. This procurement is managed by the ASC Commodities Division of the Department of Defense with Alison Allen as the primary point of contact. The item is classified under NAICS code 332722 and is subject to strict export control regulations under either ITAR or EAR, meaning any technical data associated with it cannot be disclosed to foreign persons, regardless of location, without prior authorization from the Department of State or Commerce. Disclosure includes access by foreign national employees or foreign subsidiaries of U.S. companies. Only DLA contractors with an approved US/Canada Joint Certification Program certification, completion of required DOD export control training, and successful submission of the DLA Export-Controlled Technical Data Questionnaire are permitted to access this data. DFARS 252.225-7048 governs compliance.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
BOLT, SHEARThe contract specifies the procurement of 525 shear bolts identified by NSN 5306-01-440-3621 and part number NAS6703-25, manufactured to the current revision of the non-government standard NAS6703 through NAS6720 Revision 13 dated April 30, 2026. All hardware must conform to the latest applicable part standard, with previous revisions acceptable only for items produced prior to the solicitation date. The item is classified as a critical application, subject to stringent quality controls including inspection and acceptance at destination under MIL-STD-1916 or an equivalent zero-based sampling plan, with verification levels of VII, IV, and II assigned to critical, major, and minor attributes respectively. Threads must be inspected per System 22 of FED-STD-H28/20, excluding small self-locking nuts and undersized threads. Mercury and mercury-containing compounds are strictly prohibited in the product, preservation, packaging, and marking, with only limited functional uses allowed under specific exceptions verified by NAVSEA, and portable devices containing mercury must include a secondary containment barrier. Packaging must comply with MIL-STD-2073-1E and DLA’s packaging requirements, with each fastener fully protected along its shank and threads by a wrap or sleeve, and all marking conforming to MIL-STD-129 and MIL-STD-130N for identification, excluding any special marking codes. The unit of issue is each, delivered FOB origin with no variance permitted in quantity and a delivery window of 171 days. Packaging is to be palletized in accordance with DLA guidelines, with preservation methods defined as method 10, using preservation material code 00 and drying type 1. The shipping destination and parcel post address are identical, directed to the DLA Distribution facility in New Cumberland, Pennsylvania. The required ship date is January 17, 2027, with an original delivery deadline of March 19, 2027. All quality and testing requirements are governed by the DLA Master List of Technical and Quality Requirements, and the contract is managed by the ASC Commodities Division under solicitation SPE4A6-26-T-08NL with Monica Clark as the primary point of contact.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CAP, SOCKET HEThe contract pertains to the procurement of 41 units of a socket head cap screw, identified by NSN 5305-01-582-3318 and part number AES18C375A00DG5A91, under solicitation SPE4A6-26-T-08FH. The item must conform to technical and quality standards specified in the DLA Master List of Technical and Quality Requirements, with specific mandates including MIL-STD-130N for identification marking of military property, System 22 of FED-STD-H28/20 for dimensional inspection of Class 3A and 3B threads, and compliance with ASME B18.24-2004. Sampling must adhere to MIL-STD-1916 or ASQ H1331, Table 1, with zero non-conformances required unless otherwise stated, and critical attributes are assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively. The screw is subject to Critical Item Source Inspection and must be manufactured and inspected per stringent quality assurance protocols applicable to both manufacturers and non-manufacturers. Packaging must comply with ASTM D3951 and MIL-STD-129, with palletization governed by DLA Packaging Requirements, and all units must be labeled and marked per contract specifications. The delivery is FOB origin, with inspection and acceptance occurring at the destination, and no quantity variance is permitted. The delivery window is 171 days from the award date, with an original required delivery date of March 6, 2027, and a need ship date of January 17, 2027. The item is to be shipped to the DLA Distribution facility in New Cumberland, Pennsylvania, under the Transportation Procurement Notes C19 and C20. The solicitation was issued on July 21, 2026, with responses due by July 29, 2026, and is classified under NAICS code 332722. Cybersecurity requirements are governed by CMMC Level 2, and the contract incorporates Covered Defense Information protocols. Unit price is $41.00 per piece, resulting in a total contract value of $1,681.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
STUD, PLAINThis contract pertains to the procurement of three plain studs, identified by part number 15-4046-PC NO-7 and NSN 5307-01-694-3910, supplied by Gardner Denver Nash LLC. The item is source-controlled, requiring manufacturing and testing in strict compliance with proprietary limited rights data accessible only to approved vendors who can demonstrate traceability to authorized sources. The government does not provide this data, and only qualified vendors with existing access or proven lineage to approved suppliers may submit bids. Item Unique Identification is not mandated per customer request, and the part has no shelf life. Sampling must conform to MIL-STD-1916 or ASQ H1331 Table 1 using zero-defect acceptance criteria unless otherwise specified; unspecified attributes are deemed major with AQL of 1.0. Packaging must adhere to ASTM D3951 and MIL-STD-129 labeling standards, with palletization following DLA-specific packaging requirements. All technical and quality requirements referenced by R or I numbers from the DLA Master List supersede any conflicting standards. Delivery is FOB origin, with inspection and acceptance occurring at destination in 171 days, and no variance in quantity is permitted. The unit price is $3.00 per piece for a total of $9.00. The required delivery date is February 8, 2027, with a need ship date of January 17, 2027. All shipments must be sent to the DLA Distribution facility in New Cumberland, Pennsylvania, following specified transportation protocols.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
WASHER, TANGThe contract is for a single washer, tang, identified by NSN 5310-00-089-4828, under solicitation SPE4A5-26-T-301L, with a required delivery within 20 days after award. Technical and quality requirements are incorporated by reference from the DLA Master List of Technical and Quality Requirements, with applicable revisions determined by the solicitation or award date based on acquisition size. Packaging must comply with DLA standards, non-accepted supplies must have government identification removed, and bare items must be physically marked as required. Sampling inspection follows MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances mandated unless otherwise stated, with critical, major, and minor attributes assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively. All unspecified attributes are treated as major. The solicitation was posted on July 21, 2026, with responses due by July 29, 2026, and performance is to be delivered to JBPHH, HI, 96853-1801. The contracting office is the ASC Supplier Oper OEM Division under the Department of Defense, with Anthony Nickens listed as the primary point of contact.
ASC SUPPLIER OPER OEM DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CLOSE TOLERANThis contract is for the procurement of a close tolerance screw with part number 120-225-3R08B and NSN 5305-01-581-5608, requiring 69 units to be delivered FOB origin within 146 days, with no tolerance for quantity variance. The item is classified as a critical application item and is source controlled, meaning it must be manufactured and tested using limited rights data accessible only to approved vendors who can demonstrate traceability to qualified sources. Only listed approved manufacturers, including SPS Technologies LLC, Pilgrim Screw Corporation, Fastener Innovation Technology Inc., and others, are eligible to respond. Compliance with the DLA Master List of Technical and Quality Requirements is mandatory, incorporating specific standards such as RA001, RP001, RQ011, and RQ017 for technical, packaging, identification, and marking requirements. Sampling must follow MIL-STD-1916 or an equivalent zero-based plan, with acceptance criteria requiring zero non-conformances unless otherwise stated. Documentation for source approval requires a SAR package and compliance with RC001 and RD004, including a CMMC Level 2 self-assessment. All packaging must adhere to ASTM D3951 and MIL-STD-129, with palletization following DLA-specific guidelines, and deliverables must be sent to the designated DLA Distribution facility in Cherry Point, North Carolina. The contract specifies electronic procurement compliance, unit of issue alignment with ANSI X12, and adherence to cybersecurity and data handling protocols under RD002 and RD004.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CAP, HEXAGON HEADThe contract pertains to the procurement of 1,035 units of a screw, cap, hexagon head, identified by NSN 5305-00-226-9216, under solicitation SPE4A6-26-T-08CF, with a total small business set-aside classification. Delivery is required within 146 days from award, and the item is classified as a commercial item, meaning it is procured in accordance with established military or federal specifications without custom modifications. Manufacturing must conform to the latest revision of the applicable part standard, with prior versions still acceptable for historically produced hardware, but all new production must adhere strictly to the current standard. The contract enforces stringent packaging and quality requirements aligned with DLA’s Master List of Technical and Quality Requirements, incorporating standards such as MIL-STD-1916 or ASQ H1331 for sampling, with zero non-conformances required unless otherwise specified. Critical, major, and minor attributes must be verified at designated levels or AQLs, and all identification markings must comply with MIL-STD-130N, including manufacturer logos and lot numbers. The item is subject to strict restrictions regarding mercury and mercury-containing compounds, prohibiting their intentional addition or direct contact with the hardware except for specific exempted uses such as batteries, fluorescent lights, sensors, weapon systems, or chemical reagents approved by NAVSEA, with portable devices containing mercury requiring shockproof construction and a secondary containment. The contract is issued by the Department of Defense’s ASC Commodities Division, with performance location in Bremerton, WA, and primary point of contact provided for inquiries.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
PIN-RIVETThis contract specifies the procurement of 26 units of a pin-rivet with part number HL48PY6-10 and NSN 5320-01-690-1819, supplied by HI-SHEAR CORPORATION under solicitation SPE4A6-26-T-08NZ. The item is classified as a critical application component and must comply with stringent technical and quality standards referenced in the DLA Master List of Technical and Quality Requirements, identified by R and I numbers. Inspection and acceptance are to occur at origin using MIL-STD-1916 or an equivalent zero-based sampling plan; critical, major, and minor attributes are to be verified at levels VII, IV, and II respectively, or with AQLs of 0.1, 1.0, and 4.0. Item Unique Identification is not required per customer request, and government identification must be removed from non-accepted items. Packaging must conform to MIL-STD-2073-1E and DLA-specific requirements, including marking per MIL-STD-129 with no special marking code. Delivery is FOB origin with a strict 0% variance in quantity and a required delivery date of March 6, 2027, after a 171-day lead time. The consignee is DLA Distribution at the New Cumberland facility in Pennsylvania, with transportation details governed by DLA procedural notes C19 and C20. All contractual obligations are subject to the DLA master revision in effect on the solicitation issue date.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
NUT, SELF-LOCKING, HEXAGThis contract specifies the procurement of 811 units of a self-locking hexagonal nut, identified by NSN 5310-00-269-4725 and part number MS21044C9, under solicitation SPE4A6-26-T-08BX. The item must conform to stringent technical and quality requirements referenced from the DLA Master List of Technical and Quality Requirements, including applicable standards such as NASM21044 Rev 3 and NASM25027 Rev 1, with verification levels established for critical, major, and minor attributes. Inspection and acceptance occur at origin, with mandatory compliance to MIL-STD-1916 or equivalent zero-based sampling plans and adherence to zero non-conformances unless otherwise stipulated. A Certificate of Quality Compliance and Certificate of Conformance are required, alongside detailed documentation through CDRLs and TDP Rev D, all governed by FAR 52.246-15 procedures. Packaging must follow ASTM D3951 and MIL-STD-129, with palletization in accordance with DLA’s RP001 guidelines, and all materials must be properly marked and labeled. The contract enforces strict QAPs and requires that government identification be removed from non-accepted supplies, with covered defense information controls applicable. The unit price is $811.00 per EA for a total value of $657,821, with delivery FOB origin, no quantity variance allowed, and a required delivery date of March 14, 2027, after a 101-day lead time. All items must be shipped to the specified DLA Distribution Jacksonville address, with transportation logistics governed by DLAD Proc Notes C19 and C20.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332722
New
DIBBS
WASHER, FLATThe contract specifies the procurement of 799 flat washers with the NSN 5310-01-554-5417 under solicitation SPE4A6-26-T-08EV, issued by the Department of Defense’s ASC Commodity Division. The items must comply with all applicable technical and quality requirements from the DLA Master List of Technical and Quality Requirements, which take precedence over any other standards including ASTM D3951 for packaging. Packaging and labeling must follow MIL-STD-129 and DLA Packaging Requirements, with palletization adhering to RP001. Acceptance is at destination with zero tolerance for non-conformances, and sampling must align with MIL-STD-1916, ASQ H1331, or an equivalent zero-based plan unless otherwise directed; unspecified attributes are treated as major with a verification level of IV. The contract mandates exact delivery of 799 units with no variance, FOB origin, to be shipped to Barstow, CA, with a required delivery date of March 2, 2027, and a ship date of January 17, 2027. Approved suppliers are Oshkosh Corp and Fastenal Company with specified part numbers. All documentation, including source approval, removal of government identification from rejected items, and physical marking, must meet the referenced DLA requirements. The unit of issue is each, with a total contract value of $799.00.
ASC COMMODITIES DIVISION

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details

More opportunities from Department Of Defense → ASC COMMODITIES DIVISION

Same awarding agency

NAICS: 541512
New
DIBBS
Cybersecurity Compliance & Incident ReportingThe contract requires full implementation of NIST SP 800-171 cybersecurity controls to safeguard controlled unclassified information within the contractor’s systems, alongside the development of a comprehensive System Security Plan that documents how these controls are applied and maintained. The contractor must establish processes to ensure continuous compliance with these standards and be prepared to report any cyber incident affecting covered defense information within 72 hours, in strict accordance with DFARS 252.204-7012 requirements. This effort is critical for maintaining the integrity and security of sensitive government data handled under this subcontract. This subcontract is issued under the Department of Defense by the ASC Commodities Division, with the NAICS code 541512 indicating it pertains to computer systems design services. While no set-aside type or specific point of contact is provided, the solicitation remains open for responses until August 4, 2026, with a posting date of July 21, 2026. The place of performance has not been specified, and bidders must review the full solicitation through the provided DIBBS link to ensure alignment with all technical, administrative, and reporting obligations tied to this cybersecurity compliance effort.
Computer Systems Design Services

POSTED

about 13 hours ago

DEADLINE

in 13 days
View Details
NAICS: 541330
New
DIBBS
Quality Inspection & Sampling ServicesThe contract requires the provision of quality inspection and sampling services adhering strictly to MIL-STD-1916 or ASQ H1331 sampling plans with AQL criteria, where zero nonconformances are mandatory for acceptance. Inspections must be conducted with precision to ensure all delivered products meet the defined quality standards without exception, reflecting a zero-tolerance policy for defects. The work is classified as a subcontract under NAICS code 541330 and is managed by the ASC Commodities Division within the Department of Defense, with a response deadline of August 4, 2026, and the solicitation posted on July 21, 2026. The place of performance and point of contact details are not specified, suggesting the work may be performed at multiple locations or as directed by the contracting office. Interested parties must review the full solicitation through the provided DIBBS link to understand specific deliverables, reporting requirements, and compliance obligations beyond the sampling standards outlined.
Engineering Services

POSTED

about 13 hours ago

DEADLINE

in 13 days
View Details
NAICS: 332999
New
DIBBS
Military-Compliant Packaging, Labeling & Preservation ServicesThe contract requires the provision of military-compliant packaging, labeling, and preservation services for defense shipments, adhering strictly to MIL-STD-129 and DLA RP001 standards. All materials and processes must ensure corrosion protection and full regulatory compliance for use in military logistics, with an emphasis on durability, traceability, and environmental resilience under operational conditions. The work involves end-to-end preparation of items for shipment, including proper identification, marking, and preservation techniques to safeguard equipment and supplies from degradation during storage and transit. This subcontract opportunity is managed by the ASC Commodities Division within the Department of Defense, with a response deadline of August 4, 2026, and a posting date of July 21, 2026. The NAICS code 332999 indicates it falls under other miscellaneous fabricated metal product manufacturing, suggesting the work may involve custom packaging solutions or specialized container fabrication. The place of performance and specific delivery locations are not detailed, but fulfillment is expected to support military supply chain operations globally. Interested parties must submit proposals before the deadline to be considered for award under this unspecified set-aside solicitation.
All Other Miscellaneous Fabricated Metal Product Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 13 days
View Details
NAICS: 334519
New
DIBBS
Precision Pressure Gauge Manufacturing & SupplyThe contract seeks the manufacture or supply of a military-specification pressure gauge identified by NSN 6685-01-131-8110, requiring full compliance with established material and performance standards for military applications. All units must be delivered in original, corrosion-free packaging to ensure integrity during transport and storage, and must meet all technical and quality requirements dictated by defense specifications. The solicitation is issued as a subcontract under NAICS code 334519 and is managed by the ASC Commodities Division within the Department of Defense, with responses due by August 4, 2026. The place of performance and point of contact details are not specified, but the work is expected to align with DoD procurement protocols.
Other Measuring and Controlling Device Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 13 days
View Details
NAICS: 334519
New
DIBBS
TRANSMITTER, PRESSURThe contract specifies the procurement of a pressure transmitter identified by part number 2600331-1 and NSN 6685011136087, with a requirement for two units to be delivered within 115 days to Barstow, California, under solicitation SPE4A6-26-T-08LN. The item is source-controlled and must be manufactured and tested in accordance with limited rights data held by approved sources, primarily Senso-Metrics Inc. and Soco Technologies Inc., with no government-provided technical data; only vendors with access to this data or proven traceability to approved sources may quote. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, with sampling governed by MIL-STD-1916 or ASQ H1331, adopting zero non-conformances unless otherwise directed. Specific clauses mandate that critical attributes be verified at Level VII, major at IV, and minor at II with corresponding AQLs, while unspecified attributes are treated as major. The item is designated as a critical application component and must comply with drawing 2600331 Revision E dated June 15, 2012, with certain test requirements from specification 2600380 Rev B waived and soldering procedures left to manufacturer discretion. Packaging must adhere to DLA-specific standards per RP001 and MIL-STD-129, with hazardous materials following TQ Requirement IP025 per FED-STD-313 and nonhazardous materials conforming to ASTM D3951, ensuring DLA requirements override all other standards. Item markings must comply with RQ017 for physical identification, and all packaging must be palletized per DLA guidelines. The contract imposes Cybersecurity Maturity Model Certification (CMMC) Level 2 self-assessment obligations and mandates Source Approval Request (SAR) documentation for any vendor seeking source approval. Delivery is FOB origin with zero quantity variance, inspected and accepted at destination. The unit of issue is each, priced at $2.00 per unit for a total value of $4.00, with delivery directed to the DLA Distribution Office in Barstow. The item is subject to strict compliance with documentation, cybersecurity, quality, and packaging mandates, and all contractual obligations take precedence over industry defaults.
Other Measuring and Controlling Device Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 333998
New
DIBBS
TUBE ASSEMBLY, FIRE EXTThe contract specifies the procurement of tube assemblies for a fire extinguishing system, with two approved part numbers from KIDDE TECHNOLOGIES INC: P/N 423117 and P/N 432117, classified as critical application items. The item is identified by NSN 4210-01-643-8401, with a quantity of six units, each to be delivered as a single unit of issue. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, referenced by R and I numbers including RC001 for source approval documentation, RP001 for packaging standards, RQ011 for removal of government identification from non-accepted supplies, and RQ017 for bare item marking. Sampling and inspection must adhere to MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required unless otherwise stated, and attributes are assigned verification levels or AQLs per critical, major, or minor classifications. Packaging must meet MIL-STD-2073-1E with specific preservation methods, and marking must comply with MIL-STD-129 without special codes. Palletization follows DLA packaging requirements. Delivery is FOB origin with no variance allowed in quantity, and inspection and acceptance occur at the destination. The required delivery date is January 17, 2028, with a lead time of 171 days, and shipment must be sent to the DLA Distribution Albany facility in Albany, Georgia. The contract was solicited under SPE4A6-26-T-08EA with a response deadline of July 29, 2026, and the purchasing agency is the Department of Defense, ASC Commodities Division.
All Other Miscellaneous General Purpose Machinery Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332991
New
DIBBS
BEARING, ROLLER, CYLINDRThis solicitation is for a cylindrical roller bearing, part number 59637, with NSN 3110003853504, requiring five units for delivery within 305 days FOB origin. The item is source controlled and must be manufactured and tested in strict compliance with limited rights data held by approved sources—Parker Hannifin and Regal Beloit America, Inc.—with no government provision of the technical data. Only vendors with direct access to this data or traceability to the approved sources may submit quotes. The bearing must be manufactured entirely in the United States, its outlying areas, or Canada, with more than 50 percent of the total cost of all components—rolling elements, retainer, inner and outer race—originating from these regions. A signed Contractor’s Declaration regarding domestic content is mandatory and must be submitted upon request; failure to provide it will disqualify the quote. Inspection and acceptance occur at the origin, and no unit identification is required under DFARS 252.211-7003(c)(1)(i). Packaging must fully comply with MIL-STD-2073-1E, MIL-DTL-197M, and DLA packaging requirements, including preservation methods tailored to bearing type and closure, with all marking conforming to MIL-STD-129. The item is designated as critical application and has no shelf life. All measures, testing equipment, and quality controls must meet the DLA Master List of Technical and Quality Requirements, and the entire procurement is subject to restrictions outlined in DFARS 252.225-7016. If no compliant offers are received, the solicitation may be canceled or held pending a waiver.
Ball and Roller Bearing Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336320
New
DIBBS
PANEL, INDICATING, LIGHTThe contract specifies the procurement of five units of a light-transmitting indicating panel, identified by NSN 6220-01-509-3310 and part number 74J808070-823, with delivery required within 171 days to the DLA Distribution facility in New Cumberland, Pennsylvania. The item must conform to rigorous technical and quality standards referenced through the DLA Master List of Technical and Quality Requirements, with verification levels and sampling methods strictly defined per MIL-STD-1916 or comparable zero-based sampling plans; critical, major, and minor attributes must be verified at levels VII, IV, and II with corresponding AQLs of 0.1, 1.0, and 4.0. Manufacturing and packaging adherence is mandated under DLA Packaging Requirements and MIL-STD-2073-1E, with packaging coded as U, using E5 unit containers and no cushioning material. All items must be marked per MIL-STD-129 with the special fragile code 01-01, and palletization must comply with DLA guidelines. The supplier must maintain Cybersecurity Maturity Model Certification Level 2 self-assessment compliance and remove government identification from non-accepted supplies. The delivery is FOB origin with no variance allowed in quantity, inspection and acceptance occur at destination, and the contract requires adherence to specific transportation protocols per DLAD Proc Notes C19 and C20. The original required delivery date is December 18, 2027, with a need ship date of January 17, 2027, under solicitation SPE4A6-26-T-08CN, issued by the Department of Defense’s ASC Commodities Division.
Motor Vehicle Electrical and Electronic Equipment Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 213113
New
DIBBS
BEARING, SLEEVEThe contract pertains to the procurement of a sleeve bearing with NSN 3120-01-286-0906, quantity of four units, under solicitation SPE4A6-26-T-08MV. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, with revisions controlled by the solicitation or award date depending on acquisition size. Inspection and acceptance occur at origin using sampling methods aligned with MIL-STD-1916 or ASQ H1331, Table 1, or a zero-based plan; critical, major, and minor attributes are verified at levels VII, IV, and II with AQLs of 0.1, 1.0, and 4.0 respectively. Packaging must comply with MIL-STD-2073-1E and MIL-STD-129, with no special marking required. The item is designated as a critical application requiring casting or forging, with tooling typically held by the manufacturer, and sourcing assistance must be requested through DLA’s designated channels. Only approved sources are KAMATICS CORPORATION and ROLLER BEARING COMPANY OF AMERICA, each with specific part numbers. Item Unique Identification is not required per the Service customer’s request. Delivery is FOB origin with a 171-day lead time, final delivery due by April 20, 2027, and shipment must be directed to the DLA Distribution facility in New Cumberland, Pennsylvania. Packaging and palletization adhere strictly to DLA’s procurement standards, and all documentation must support source approval and manufacturing compliance.
Support Activities for Coal Mining

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 334419
New
DIBBS
LIGHT, INDICATORThe contract specifies the procurement of a light indicator component with NSN 6210011737858 under solicitation SPE4A6-26-T-08UD, requiring delivery of three units at one each to the USS FRANK E PETERSEN JR DDG 121 at FPO AP 96691 by June 25, 2026, with a 20-day delivery window and FOB destination terms. Strict compliance with DLA packaging standards MIL-STD-2073-1E and marking requirements MIL-STD-129 is mandated, including fragile labeling and prohibition of mercury or mercury compounds in preservation, packaging, or marking. The item is classified as a critical application with bare part marking requirements for DRS NAVAL POWER SYSTEMS INC P/N 6981ED166-535, and sampling must follow MIL-STD-1916 or ASQ H1331 with zero non-conformances unless otherwise specified. All technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements referenced online, with revisions controlled by the solicitation or amendment date. No shelf life applies, and quantity variance is strictly zero percent. Shipping and transportation follow DLAD procedural notes C19 and C20, with vendors required to use VSM for logistics. The contract enforces zero tolerance for mercury exposure and mandates compliance with verified sampling levels and packaging codes for unit containment and protection.
Other Electronic Component Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332510
New
DIBBS
RING, RETAININGThe contract covers the procurement of 1,585 retaining rings with NSN 5325-00-169-8023 under solicitation SPE4A6-26-T-08HH, with a delivery deadline of 171 days after award. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements referenced by R or I numbers, with revision control based on solicitation or award date depending on acquisition size. Packaging must comply with DLA standards, and non-accepted supplies must have government identification removed. Items must bear physical identification per bare item marking requirements. Sampling follows MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required unless otherwise stated; critical, major, and minor attributes are verified at levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively. Item Unique Identification is not required per customer request. Tailored quality requirements apply to both manufacturers and non-manufacturers, with inspection and acceptance occurring at origin. Technical data associated with this item is subject to export controls under ITAR or EAR, prohibiting unauthorized disclosure to foreign persons anywhere, with DFARS 252.225-7048 enforcing compliance. Access to controlled data is restricted to contractors with approved US/Canada Joint Certification Program certification, completed DOD export control training, and DLA authorization. The place of performance is New Cumberland, PA, and the point of contact is Monica Clark of the ASC Commodities Division, Department of Defense.
Hardware Manufacturing

POSTED

about 13 hours ago

DEADLINE

in 7 days
View Details