SEMICONDUCTOR DEVICE, D

SEMICONDUCTOR DEVICE,DIODE
SEMICONDUCTOR DEVICE, DIODE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ014: QUALIFIED SUPPLIERS LIST OF DISTRIBUTORS (QSLD) AND QUALIFIED
TESTING SUPPLIERS LIST (QTSL) FOR FEDERAL SUPPLY CLASS (FSC) 5961
SEMICONDUCTORS AND HARDWARE DEVICES AND FSC 5962 ELECTRONIC
MICROCIRCUITS. THIS IS A QUALIFIED ITEM. QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE M01 "QUALIFIED SUPPLIERS FOR FEDERAL SUPPLY CLASS (FSC)
5961 SEMICONDUCTORS AND HARDWARE DEVICES AND FSC 5962 ELECTRONIC
MICROCIRCUITS" APPLY.
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ018: CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION
(AUG 2016)
This item requires supply chain traceability documentation in accordance with DLA Directive (DLAD) Procurement Notes #C03 Contractor Retention of Supply Chain Traceability Documentation (AUG 2016)#. The full text of C03 can be found in the DLAD Procurement Notes on the Web at: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. (End of TQ Requirement)
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
SPE7M5-26-T-508K
SECTION B
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
KATO ENGINEERING
CAGE 32770
P/N 850-43930-50
KATO ENGINEERING INC. 32770 P/N 099-00222-03 ITEM 22.13
KATO ENGINEERING INC. 32770 P/N 850-43930-50
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018378978 0001 EA 12.000
NSN/MATERIAL:5961015513776
DELIVERY (IN DAYS):0179
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:GX CLNG/DRY:1 PRESV MAT:00
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:C
UNIT CONT:ZZ OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:39 -39 ESD sensitiv electrnic dvce
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PACKAGING SHALL BE IAW MIL-PRF-23199E. MARKING/LABELING/ BAR CODING SHALL BE IAW MIL-STD-129.
UNIT PACKAGE MARKING REQUIREMENT FOR COMPONENT LEAD FINISH
(a) In addition to all other marking requirements in this contract, the Contractor shall apply one of the assigned markings in accordance with paragraphs 5.3.1 and 5.3.2 of IPC/JEDEC J-STD-609, Marking and Labeling of Components, printed circuit boards (PCBs) and printed circuit board assemblies (PCBAs) to Identify Lead (Pb), Pb-Free and Other Attributes, to each individual unit pack of the item being acquired. Placement of the markings shall be in accordance with paragraph 6.2 of the standard.
(b) Copies of the current version of this standard may be purchased or
SPE7M5-26-T-508K
SECTION B
PR: 7018378978 PRLI: 0001 CONT’D
downloaded from the Association Connecting Electronics Industry (IPC), http://www.ipc.org, http://www.ipc.org, or the Solid State Technology Association (JEDEC), http://www.jedec.org. http://www.jedec.org.
ESD and PHYSICAL protection are required for contacts, leads, terminals, and other protrusions by means of container design, cushioning, and/or other ESD protective devices. Components with pins or leads shall have adequate cushioning to PREVENT DAMAGE, BREAKAGE and/or BENDING OF LEADS when not specified in the packaging codes.
This item requires DOD QUALIFIED Electrostatic Discharge (ESD) and/or Electromagnetic Interference (EMI) protective packaging materials in accordance with MIL-PRF-81705. All items subject to degradation from ESD/EMI environmental field forces shall be handled and packaged at an approved field force protective work station.
For ESD protection MIL-PRF-81705, Type I (MIL-DTL-117, Type I, Class F, Style 1) converted bag barrier material shall be used along with MIL-PRF-81705, Type III (MIL-DTL-117 Type II, Class H, Style 2) barrier material wrap if the contract doesn't specifically require ESD approved cushioning.
For EMI protection MIL-PRF-81705, Type I (MIL-DTL-117, Type I, Class F, Style 1) converted bag barrier material shall be used.
The supplier shall be responsible for verifying that all MIL-PRF-81705 barrier materials (or converted bags) were supplied from a qualified manufacturer currently listed on QPL-81705.
For additional ESD/EMI packaging information, refer to the following DLA packaging website: https://www.dla.mil/HQ/LogisticsOperations/Packaging/PackFAQs/ESDS/
If the preservation method code in the solicitation does not specify ESD/EMI protection and the Offeror's proposed item of supply is subject to degradation from ESD/EMI environmental field forces, Offerors shall provide appropriate technical packaging data with their proposals.
IP027: PACKING AND MARKING REQUIREMENTS FOR FEDERAL STOCK CLASS 5961 SEMICONDUCTORS AND HARDWARE DEVICES AND FSC 5962 ELECTRONIC MICROCIRCUITS
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
SPE7M5-26-T-508K
SECTION B
PR: 7018378978 PRLI: 0001 CONT’D
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:03/27/2027 Original Required Delivery Date:03/27/2027
SPE7M5-26-T-508K NSN/Part Number: 5961-01-551-3776 Quantity: 12 EA Purchase Request: 7018378978QTY: 12 Delivery: 179 days ADO