Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, August 19 at 2:00 PM EDT

Register Free →
logo
Get CLEATUS

SETSCREW

Active
SPE4A6-26-T-12VGFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

Show more

The contract is for the procurement of 12 set screws identified by NSN 5305-01-414-2862 under solicitation SPE4A6-26-T-12VG, with a delivery requirement of 70 days after delivery order issuance. The procurement is governed by stringent technical and quality standards referenced from the DLA Master List of Technical and Quality Requirements, and incorporates cybersecurity maturity requirements including CMMC Level 2 certification for the third-party assessment organization involved. The item is subject to export control under either ITAR or EAR, meaning any handling, disclosure, or transfer of associated technical data to foreign persons—including foreign nationals within the United States or overseas—is strictly prohibited without prior authorization from the Department of State or Commerce. Contractors must hold an approved US/Canada Joint Certification Program credential, complete mandatory DLA training on export-controlled data, and pass the DLA Export-Controlled Technical Data Questionnaire to gain access. Compliance with DFARS 252.225-7048 is mandatory, and the distribution of technical data is restricted to authorized DLA contractors with verified eligibility. The place of performance is New Cumberland, PA, with a zip code of 17070-5002. The solicitation was posted on August 5, 2026, and responses are due by August 13, 2026, with the contracting office under the Department of Defense’s ASC Commodities Division. The primary point of contact is Stephanie Sandridge, reachable via email at stephanie.sandridge@dla.mil.

General Info

Procure 12 set screws NSN 5305-01-414-2862, deliver in 70 days, CMMC Level 2, ITAR/EAR controlled, US/Canada certification required.

Agency

Department Of Defense → ASC COMMODITIES DIVISIONView Agency

NAICS

332722 - Bolt, Nut, Screw, Rivet, and Washer ManufacturingView NAICS

Place of Performance

2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, US

Set-Aside

NONE

Documents

(1)

SPE4A6-26-T-12VG.pdf

PDF

AI Contract Breakdown

Uniform Contract Format

What is UCF?

Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.

Timeline

PhaseSolicitation
Posted

Solicitation

Response Deadline

Submission deadline

Response Deadline

Ready to pursue this opportunity?

Start your free trial to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC COMMODITIES DIVISION
Contacts1 person available
OfficeUS
Organization / Agency
Department Of Defense → ASC COMMODITIES DIVISION
View Agency Profile
Office AddressUS
Contacts
STEPHANIE SANDRIDGE
contact@example.gov

Full Description

Show more
SETSCREW
SETSCREW
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO) RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD002, COVERED DEFENSE INFORMATION APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 5305-01-414-2862 Quantity: 12 EA Purchase Request: 7017763646QTY: 12 Delivery: 70 days ADO

Similar Contracts

Same NAICS industry code

NAICS: 332722
New
DIBBS
NUT, PLAIN, HEXAGON
Solicitation # SPE4A6-26-R-XB62
The contract specifies the procurement of 300 hexagon plain nuts, identified by NSN 5310-01-368-5549, under solicitation SPE4A6-26-R-XB62, with a firm fixed price and zero variance in quantity. The item is classified as a critical safety item and a critical application item for Martin-Baker Aircraft Company Limited, with part number MBEU146543, requiring strict adherence to quality and configuration controls. All supplies must comply with MIL-STD-129 for marking, including lot and serial numbers, contractor and manufacturer CAGE codes, and part numbers, while packaging must follow MIL-STD-2073-1E and DLA’s packaging requirements. Inspection and acceptance occur at origin, and sampling must conform to MIL-STD-1916 or ASQ H1331 with zero non-conformances required, assigning verification levels VII, IV, and II to critical, major, and minor attributes respectively. The contract incorporates technical and quality requirements from the DLA Master List referenced online, and non-tailored higher-level quality standards including SAE AS9100 apply. Waivers or deviations require explicit approval from the DSC contracting officer. Delivery is due 240 days after contract award, with FOB origin terms, and transportation details are governed by DLAD procedural notes. The item is subject to covered defense information regulations and the use of calibrated measuring and test equipment as specified under RT001.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 9 days
View Details
NAICS: 332722
New
DIBBS
PLUG, MACHINE THREAD
Solicitation # SPE4A7-26-Q-0974
The contract pertains to the procurement of seven units of a machine thread plug with NSN 5365-00-854-2899, issued under solicitation number SPE4A7-26-Q-0974 by the Department of Defense’s ASC SUPPLIER OPER AE AND AF DIV. Delivery is required within 182 days after contract award, and responses must be submitted by August 15, 2026. Technical data associated with this item is subject to strict export controls under either ITAR or EAR, meaning any disclosure to foreign persons—even within the United States—is prohibited without prior authorization from the Department of State or Department of Commerce. DFARS 252.225-7048 governs the handling of this controlled information, and only contractors certified under the US/Canada Joint Certification Program, with completed DLA training and approved access, are permitted to receive the technical data. The primary point of contact for the solicitation is Mykhara Robinson, reachable via email at mykhara.robinson@dla.mil.
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 2 hours ago

DEADLINE

in 10 days
View Details
NAICS: 332722
New
DIBBS
COLLAR, PIN-RIVET
Solicitation # SPE4A6-26-T-12TU
The contract pertains to the procurement of 822 units of COLLAR, PIN-RIVET with NSN 5320-01-596-1012 and part number HL379-6, sourced from approved manufacturers including HOWMET GLOBAL FASTENING SYSTEMS INC and HI-SHEAR CORPORATION. Delivery is required FOB origin within 121 days, with no variance allowed in quantity, and inspection and acceptance must occur at the manufacturing origin in compliance with stringent quality standards. All items must adhere to MIL-STD-2073-1E packaging requirements and MIL-STD-129 marking standards, with no special marking codes applied. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, referenced by R and I numbers, and sampling must follow MIL-STD-1916 or ASQ H1331, Table 1, with zero non-conformances required unless otherwise stated. Critical threads must be gaged per SAE AS8879 Category 1 or MIL-S-7742, excluding self-locking nuts and small-diameter threads. Documentation for source approval is mandated, and all supplies must meet tailored higher-level quality requirements. Item Unique Identification is not required per Service customer direction. The delivery destination is the DLA Distribution facility in New Cumberland, Pennsylvania, and transportation logistics follow DLA procedural notes C19 and C20. The contract was solicited under SPE4A6-26-T-12TU with a response deadline of August 13, 2026, and a required ship date of December 13, 2026.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CAP, SOCKET HE
Solicitation # SPE4A6-26-T-12TP
The contract specifies the procurement of 65 socket head cap screws identified by NSN 5305-01-660-8339 and part number NAS1352-8-LN-28, manufactured to the current revision of the non-government standard NAS1352 Revision 13 dated 05/31/2016. All hardware must comply with this standard, and previously approved revisions are acceptable only for items manufactured before the solicitation date. The item is classified as a critical application component, requiring strict adherence to physical identification and bare item marking requirements under RQ017, and must be marked in accordance with MIL-STD-129 without special marking codes. Packaging must conform to MIL-STD-2073-1E, including preservation method 33, dry conditions, and use of BV unit containers, with palletization following DLA's packaging requirements. Mercury and mercury-containing compounds are strictly prohibited in the product, preservation, packaging, and marking except for specific exemptions like batteries or instruments as defined by NAVSEA, and any such exempt items must include a secondary containment. Sampling for quality verification follows MIL-STD-1916 or a comparable zero-based plan, with critical, major, and minor attributes assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively; zero non-conformances are required unless otherwise stated. The item is delivered FOB origin with a 109-day delivery window, inspection and acceptance occurring at destination, and no variance is permitted in quantity. Delivery is directed to DLA Distribution at the New Cumberland, Pennsylvania facility.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
CONTRACTOR FIRST ARTIC
Solicitation # SPE4A6-26-T-12TT
The contract specifies the procurement of a shear bolt, identified by NSN 5306013653161, with a quantity of 276 units, governed by strict technical, quality, and packaging standards. The item must comply with the NAS1303 through 1320 standard, Revision 13 dated 01/31/2001, and reference drawing 13873 EI-013653161, Revision dated 07/10/2026, with manufacturing required to adhere to the current revision of the governing standard as of the solicitation date. All hardware manufactured going forward must meet the latest version of the applicable part standard, and previous revisions are only acceptable if they were current at the time of production. Inspection requirements mandate dimensional conformance of all Class 3A and 3B threads according to SYSTEM 22 of FED-STD-H28/20, excluding small internal and external threads below specified diameters. Sampling must follow MIL-STD-1916 or ASQ H1331 with zero non-conformances required unless otherwise defined, with attributes classified as critical, major, or minor assigned corresponding verification levels or AQLs. The item is designated as a critical application and requires compliance with DLA’s Master List of Technical and Quality Requirements, which override other standards. Packaging must conform to ASTM D3951 and MIL-STD-129 for marking and labeling, with palletization following DLA’s RP001 guidelines. Identification marking adheres to MIL-STD-130N, and while Item Unique Identification is not mandated, all other manufacturer and lot markings are required. Delivery is FOB origin, with inspection and acceptance occurring at the point of manufacture. The delivery timeframe is 240 days, with no variance permitted in quantity. A separate line item for First Article Testing is included with one unit designated, though the actual test quantity is defined in FAR clauses cited in Section A, and pricing for this item is required for evaluation. The contract references DLA procedural notes for transportation and provides the shipping destination as Tinker AFB, Oklahoma. The solicitation closes on August 13, 2026, with a performance need date of September 13, 2026.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
NUT, SELF-LOCKING, AS
Solicitation # SPE4A6-26-T-12UT
The contract specifies the procurement of 28 self-locking nuts with assembled washers, identified by NSN 5310-00-163-7561, under solicitation SPE4A6-26-T-12UT, with a response deadline of August 13, 2026, and a delivery requirement of 256 days after order. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, with compliance tied to the revision in effect on the solicitation or award date depending on acquisition size. The item is subject to strict export controls under ITAR or EAR, prohibiting any unauthorized disclosure of technical data to foreign persons, including foreign nationals within the U.S., and requiring compliance with DFARS 252.225-7048. Only contractors with approved US/Canada Joint Certification Program status, completed DOD export control training, and DLA authorization may access the controlled data. Sampling must follow MIL-STD-1916 or ASQ H1331 with zero non-conformances required unless otherwise stated, and attributes are classified with verification levels or AQLs of VII, IV, and II for critical, major, and minor characteristics respectively. Quality conformance inspections, measuring equipment standards, and DLA packaging requirements are mandated, and government identification must be removed from rejected items. Cybersecurity compliance requires CMMC Level 2 certification by a certified third-party assessment organization, and physical identification markings on the bare item are required. The point of contact for inquiries is Molitauoleava Langi, and performance is to occur in New Cumberland, Pennsylvania.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
GOVERNMENT FIRST ARTIC
Solicitation # SPE4A6-26-T-12UY
This contract pertains to the procurement of PIN-RIVET components identified by NSN 5320016069638 and a separate first article test item identified by NSN 0001S00000052, both governed by stringent technical and quality standards outlined in the DLA Master List of Technical and Quality Requirements. The hardware must conform to the current revision of applicable non-government standards, specifically NAS4450 Revision 4 and NAS4444 Revision 6, with past production to previous revisions still acceptable provided they were current at the time of manufacture. All items are classified as commercial items and must meet tailored quality requirements including inspection and acceptance at origin, mandatory physical identification and bare item marking, and removal of government identification from non-conforming supplies. Sampling must follow MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required unless otherwise specified, and attributes are to be classified with verification levels or AQLs as designated. A Certificate of Quality Compliance is required, and packaging must adhere to MIL-STD-2073-1E and DLA packaging standards, with marking in compliance with MIL-STD-129 and no special marking codes applied. The contract includes one line item for 260 units of the PIN-RIVET at a unit price of $260.00, with delivery required within 410 days FOB origin, and a second line item for one unit designated for first article testing, priced at $1.00 but not subject to separate payment unless the test requirement is fulfilled and not waived. Both items have zero quantity variance and are to be delivered to the DLA Distribution facility in New Cumberland, Pennsylvania, with the need ship date set for January 31, 2027 and the original required delivery date of December 26, 2026. The first article test item has no specified delivery date, reflecting its role as a testing requirement contingent on government evaluation. The procurement is subject to government oversight including potential first article testing under FAR clauses referenced, and compliance with all applicable DLA procedural notes for transportation and logistics. The contract emphasizes rigid adherence to documented standards and requires full alignment with DLA’s technical data package and quality assurance provisions.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CAP, HEXAGON HEAD
Solicitation # SPE4A6-26-T-12TX
The contract specifies the procurement of 494 units of a hexagon head cap screw with NSN 5305-00-907-0044 under solicitation SPE4A6-26-T-12TX, with a delivery requirement of 170 days and FOB origin terms. All items must comply with strict technical and quality standards referenced from the DLA Master List of Technical and Quality Requirements, including specific packaging, marking, and inspection protocols per MIL-STD-2073-1E and MIL-STD-129. Sampling must adhere to MIL-STD-1916 or ASQ H1331 with zero non-conformances required unless otherwise stated, and critical attributes are assigned verification levels VII, IV, and II. The screw must conform to NASM35307 Revision 2 and other referenced specifications, with no intentional addition of mercury or mercury-containing compounds in any component or contact material, except for certain exempted applications like batteries or sensors as defined by NAVSEA; portable devices containing mercury must include a secondary containment. Packaging and preservation must follow DLA requirements, prohibiting mercury in preservation materials, with palletization and unit packaging details outlined under RP001 and QUP 050. The delivery destination is the DLA Distribution facility in New Cumberland, Pennsylvania, with a required ship date of January 31, 2027, and the original delivery date set for July 16, 2027. The contract enforces a strict zero variance in quantity, with inspection and acceptance occurring at origin, and all documentation, labeling, and compliance obligations are mandatory for both manufacturers and non-manufacturers.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
NUT, PLAIN, SLOTTED, HEXA
Solicitation # SPE4A6-26-T-12UH
The contract pertains to the procurement of 251 plain, slotted hexagon nuts identified by NSN 5310-01-216-3677 under solicitation SPE4A6-26-T-12UH, issued by the Defense Logistics Agency’s ASC Commodities Division. Delivery is required within 164 days of award, with full technical and quality requirements governed by the DLA Master List of Technical and Quality Requirements, referenced via R or I numbers, and subject to the revision in effect on the solicitation issue date. Packaging must comply with DLA standards, and government identification must be removed from non-accepted supplies. Inspection and acceptance may occur at origin, and quality conformance inspections are required. A Certificate of Conformance is authorized unless explicitly withheld by a Quality Assurance Letter of Instruction. Technical data associated with this item is subject to export control under either ITAR or EAR, restricting unauthorized disclosure to foreign persons, regardless of location, and applies to all contractors, including foreign subsidiaries. Access is limited to DLA contractors certified under the US/Canada Joint Certification Program, who have completed mandatory training on handling export-controlled data and been formally approved by DLA. The data is further governed by DFARS 252.225-7048. Covered defense information applies, and the place of performance is specified as New Cumberland, PA, with ZIP code 17070-5002. The solicitation opened on August 5, 2026, with a response deadline of August 13, 2026, and is classified under NAICS code 332722. Primary point of contact is Krystle Bailey, reachable via email and phone provided.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
SCREW, CAP, SOCKET HEAD
Solicitation # SPE4A6-26-T-12VB
The contract is for the procurement of 32 units of SCREW, CAP, SOCKET HEAD, identified by NSN 5305-01-330-6346, and is being procured under a fully competitive process in compliance with military and federal specifications. The purchase request number is 7017742042, and the delivery is scheduled 170 days after award. The solicitation, numbered SPE4A6-26-T-12VB, was posted on August 5, 2026, with a response deadline of August 13, 2026. The procurement falls under NAICS code 332722 and is managed by the ASC Commodity Division within the Department of Defense. The place of performance is in Tracy, California, with a ZIP code of 95304-5000. Primary point of contact for the solicitation is Nyjel Knowlin, reachable at nyjel.knowlin@dla.mil. The acquisition is conducted through the DIBBS platform, with the official solicitation page accessible via the provided UI link.
ASC COMMODITIES DIVISION

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
BOLT, CLEVIS
Solicitation # SPE4A7-26-T-617Y
The contract is for the procurement of 1,429 units of BOLT, CLEVIS with NSN 5306-00-151-3538 under solicitation SPE4A7-26-T-617Y, issued by the Department of Defense through ASC SUPPLIER OPER AE AND AF DIV. Delivery is required within 170 days of award, with FOB origin terms and inspection and acceptance occurring at the destination facility in New Cumberland, Pennsylvania. The unit of issue is each, with no tolerance for quantity variance. All supplies must comply with the DLA Master List of Technical and Quality Requirements, which take precedence over other standards, and packaging must adhere to ASTM D3951 as well as MIL-STD-129 for marking and labeling. Palletization must meet DLA Packaging Requirements, and government identification must be removed from non-accepted items. Sampling and inspection follow MIL-STD-1916 or a comparable zero-based plan, with verification levels or AQLs assigned based on attribute criticality, and zero non-conformances required unless otherwise specified. Identification markings must conform to MIL-STD-130N in addition to manufacturer-specific data. The required delivery date is March 25, 2027, with a need ship date of January 31, 2027, and the contract references specific DLA transportation procedures for shipping and first destination handling.
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details
NAICS: 332722
New
DIBBS
BOLT, 1-8X14
Solicitation # SPE4A0-26-T-4171
The contract specifies the procurement of 4 units of BOLT, 1-8X14, with NSN 5306015037927, under solicitation SPE4A0-26-T-4171, issued by the Department of Defense through the Aviation Supply Chain ESOc Buys office. Delivery is required within five days of contract award, FOB origin, with no tolerance for quantity variance. The item must be packaged in compliance with MIL-STD-2073-1E, marked per MIL-STD-129, and palletized according to DLA packaging requirements. Inspection and acceptance occur at the destination, with zero non-conformances required in sampling under MIL-STD-1916 or comparable zero-based plans unless otherwise stated, and attributes are to be categorized with specified verification levels or AQLs. The manufacturer is identified as JLG Industries, Inc. with part number 8310480, and technical and quality standards referenced are governed by the DLA Master List of Technical and Quality Requirements. Shipping instructions mandate traceable freight methods, excluding parcel post, with delivery directed to the Distribution Management Office at Camp Lejeune, North Carolina, under a specific military freight code and project designation. The original required delivery date is July 31, 2026, and the contract includes specific government-use only metadata and point of contact information.
AVIATION SUPPLY CHAIN ESOC BUYS

POSTED

about 2 hours ago

DEADLINE

in 8 days
View Details

More opportunities from Department Of Defense → ASC COMMODITIES DIVISION

Same awarding agency

NAICS: 561730
New
DIBBS
Erosion Control and Landscaping
Landscaping Services

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 561990
New
DIBBS
Traffic Control and Signage
All Other Support Services

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 332312
New
DIBBS
Steel Fabrication and Erection
Fabricated Structural Metal Manufacturing

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 541370
New
DIBBS
Surveying and Layout Services
Surveying and Mapping (except Geophysical) Services

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 541620
New
DIBBS
Environmental Site Assessment and Remediation
Environmental Consulting Services

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 237310
New
DIBBS
Asphalt Paving and Site Surfacing
Highway, Street, and Bridge Construction

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 238110
New
DIBBS
Concrete Forming and Placement
Poured Concrete Foundation and Structure Contractors

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 238220
New
DIBBS
Plumbing and Piping Systems Installation
Plumbing, Heating, and Air-Conditioning Contractors

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 327320
New
DIBBS
Ready-Mix Concrete Supply
Ready-Mix Concrete Manufacturing

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 238210
New
DIBBS
Electrical Installation and Wiring Services
Electrical Contractors and Other Wiring Installation Contractors

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details
NAICS: 334332
New
DIBBS
Military-Grade Cable Assembly Manufacturing and Supply

POSTED

about 2 hours ago

DEADLINE

in 15 days
View Details
NAICS: 332991
New
DIBBS
BEARING, ROLLER, AIRFRAME
Solicitation # SPE4A6-26-R-XC13
The contract is for one roller bearing, airframe model DAS6-25C, identified by NSN 3110-00-143-3010, under solicitation SPE4A6-26-R-XC13. The item is classified as a critical application component and must be manufactured entirely in the United States, its outlying areas, or Canada, with over 50% of the total cost of all bearing components—rolling elements, retainer, inner race, and outer race—originating from these regions. A signed contractor’s declaration confirming the domestic origin of materials is required and must be submitted upon request; failure to provide this will disqualify the quote. The solicitation is subject to cancellation if no compliant offers are received, with potential reinstatement only after a formal waiver is approved. Pricing is firm fixed, with no variance allowed in quantity, and delivery is due 177 days after award. Inspection and acceptance occur at destination, with FOB terms also at destination. Packaging and preservation must follow MIL-STD-2073-1E, MIL-DTL-197M, and all DLA packaging requirements, including specific preservation methods determined by bearing type and closure, approved lubricants, and stringent quality verification controls. Marking must comply with MIL-STD-129 using special marking code ZZ-ZZ and no government identification may be removed from non-accepted supplies. Unit of issue is each, and no item unique identification is required per the service customer’s request. Measuring and test equipment must be calibrated and traceable, and documentation for source approval is governed by RC001. All technical and quality requirements referenced by R or I numbers are incorporated from the DLA Master List of Technical and Quality Requirements. The solicitation was issued on August 5, 2026, with responses due by August 19, 2026.
Ball and Roller Bearing Manufacturing

POSTED

about 2 hours ago

DEADLINE

in 14 days
View Details