Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, July 22 at 2:00 PM EDT

Register Free →
logo
Get CLEATUSFree Trial

SINK ASSEMBLY, HAND

Active
SPE8E8-26-T-4696Federal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

Show more

The contract is for the procurement of 31 units of a sink assembly, hand, identified by NSN 4540-01-486-4399, under solicitation SPE8E8-26-T-4696, with a delivery requirement of 128 days after award. The item must be manufactured with a specific drain part number J35 installed into the sink assembly SL-2019-A-CR, and all units must comply with MIL-STD-130N for identification marking of U.S. military property. Quality compliance is mandated through contract data requirements lists including CoQC, RQ006, RQ009, and RQ011, which dictate inspection, acceptance at origin, and removal of government identification from non-accepted items. Sampling must adhere to MIL-STD-1916 or ASQ H1331 Table 1 using a zero-based plan unless otherwise specified, with attributes classified as critical, major, or minor assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively. Unspecified attributes are treated as major, and zero non-conformances are required in sample lots unless contract exceptions apply. Certification of material compliance with specified standards is mandatory, and source inspection is required. Technical drawings are accessible only during the open solicitation period via the DIBBS portal. The solicitation was posted on July 8, 2026, with responses due by July 20, 2026, and is procured as fully competitive under federal specifications. The contract references the DLA Master List of Technical and Quality Requirements for all technical and quality clauses denoted with R or I numbers, and all provisions are controlled by the version of the Master List effective on the RFP issue date. The contracting office is the DLA New Cumberland Facility, with primary point of contact Alexis Selby.

General Info

DLA seeks 31 hand sink assemblies by July 20, 2026, via solicitation SPE8E8-26-T-4696.

Agency

Department Of Defense → DDSP NEW CUMBERLAND FACILITYView Agency

NAICS

333414 - Heating Equipment (except Warm Air Furnaces) ManufacturingView NAICS

Place of Performance

2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, US

Set-Aside

NONE

Documents

(1)

SPE8E8-26-T-4696.pdf

PDF

AI Contract Breakdown

Uniform Contract Format

What is UCF?

Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.

Timeline

1 update
PhaseSolicitation
Posted

Solicitation

Amendment 1

Contract was updated

Response Deadline

Submission deadline

Response Deadline

Ready to pursue this opportunity?

Start your free trial to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → DDSP NEW CUMBERLAND FACILITY
Contacts1 person available
OfficeUS
Organization / Agency
Department Of Defense → DDSP NEW CUMBERLAND FACILITY
View Agency Profile
Office AddressUS
Contacts
Alexis Selby
contact@example.gov
+1 (555) 000-0000

Full Description

Show more
SINK ASSEMBLY,HAND
SINK ASSEMBLY,HAND
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
US ARMY NATICK (81337) NATICK, MA ADDITIONAL REQUIREMENT: JUST
MANUFACTURING P/N J35 DRAIN TO BE INSTALLED IN JUST MANUFACTRING SINK
P/N SL-2019-A-CR. IDENTIFY TO:
MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
SPE8E8-26-T-4696
SECTION B
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
QAP EQ003 APPLIES
CONTRACTOR SHALL PROVIDE CERTIFICATION/DOCUMEN
TATION TO THE QUALITY ASSURANCE REPRESENTATIVE
THAT MATERIAL COMPLIES WITH THE MATERIAL SPECI
FICATION IDENTIFIED IN THE CONTRACT/PURCHASE
ORDER.
SOURCE INSPECTION REQUIRED.
THIS NSN IS PROCURED AS FULLY COMPETITIVE IN
ACCORDANCE WITH A MILITARY / FEDERAL
SPECIFICATION/STANDARD. SEE NSN/Part Number: 4540-01-486-4399 Quantity: 31 EA Purchase Request: 7017422403QTY: 31 Delivery: 128 days ADO

Similar Contracts

NAICS: 333414
New
DIBBS
FAN, VANEAXIALThe contract specifies the procurement of one axial flow fan identified by NSN 4140-01-602-0616 and part number FF-18504 REV B, sourced from FM AF, LLC under solicitation SPE8E7-26-T-3345. Delivery is required within five days of award, FOB origin, with no variance permitted in quantity, and inspection and acceptance occur at the destination. All packaging must comply with ASTM D3951 and adhere strictly to MIL-STD-129 for marking and labeling, with palletization following DLA’s RP001 packaging requirements, which take precedence over any general standards. The item must be shipped by the fastest traceable means, explicitly prohibiting parcel post, and delivered to the specified freight address in National City, California, with an alternate parcel post address provided solely for non-shipping correspondence. The contract incorporates by reference the full DLA Master List of Technical and Quality Requirements, whose applicable revision is determined by the solicitation or award date depending on acquisition size, and mandates strict compliance with all referenced requirements marked with R or I numbers. Shipping instructions include a TCN identifier and project code for tracking, while government-only fields such as IPD, DIC, DIST, ADV, and FC provide internal logistics and disposition controls. The required delivery date is July 10, 2026, and the point of contact for inquiries is Kelly Mitchell of the Defense Logistics Agency, with all procurement governed under DoD unit of issue standards and the NAICS code 333414 for fan and blower manufacturing.
Defense Logistics Agency

POSTED

about 9 hours ago

DEADLINE

in 11 days
View Details
NAICS: 333414
New
DIBBS
Commercial Off-the-Shelf (COTS) Fan SupplyThe contract solicits the procurement and delivery of three military-grade vaneaxial fans identified by NSN 4140009620215, requiring full compliance with hazardous materials handling protocols and defense logistics standards. These units are classified as commercial off-the-shelf items and must meet stringent performance and environmental specifications mandated for defense applications. The procurement is structured as a subcontract under the Department of Defense, specifically managed by the Construction & Equipment MRO SVC I agency, with performance required at Tinker Air Force Base in Oklahoma, ZIP 73145-8000. The solicitation, posted on July 9, 2026, requires responses by July 20, 2026, and is governed under NAICS code 333414, which pertains to ventilation and air conditioning equipment manufacturing. All deliverables must ensure seamless integration into existing military infrastructure and adhere to federal defense acquisition regulations without exception.
CONSTRUCTION & EQUIPMENT MRO SVC I

POSTED

4 days ago

DEADLINE

in 7 days
View Details
NAICS: 333414
New
Federal
Supply of Industrial Air ExtractorsThe contract calls for the procurement and delivery of two industrial air extractors, each with a minimum extraction capacity of 1080 cubic meters per hour, to be installed at the CENOP facility in Colombia. The scope includes full technical validation to ensure compliance with performance requirements, adherence to all applicable export compliance regulations, and comprehensive warranty support to guarantee long-term operational reliability. The equipment must meet specified engineering standards and be suitable for use in the environmental and operational conditions of the Colombian facility. Submitted proposals must be received by August 10, 2026, and the contract is classified as a subcontract under NAICS code 333414 for ventilation and air conditioning equipment manufacturing. The solicitation is issued by the U.S. Department of State through the American Embassy in Bogota, with performance occurring exclusively at the CENOP facility. While no set-aside provisions apply, all vendors are expected to comply with international trade and export control requirements, and successful bidders will be responsible for logistics, installation readiness, and post-delivery technical support.
American Embassy Bogota - Nas

POSTED

5 days ago

DEADLINE

in 28 days
View Details
NAICS: 333414
New
Canada
Heater, Fluid, ElectricThe Department of National Defence is soliciting five electric fluid heaters with part number TMO-6065E4T1WXX 440V 3 PHASE 3KW and NCAGE 07131 for delivery to CFB Halifax, and three identical units for delivery to CFB Esquimalt, under solicitation number W8482-264761/A. These heaters are intended for use in controllable pitch propellers and propeller shafting on HFX class ships and must conform to the latest specifications and drawings in effect on the bid closing date, with all materials required to be new production from the principal manufacturer or its accredited agent. Bidders may propose equivalent or substitute products but must provide the manufacturer’s part number, NCAGE, and certification from the original equipment manufacturer or its authorized agent confirming identical fit, form, function, quality, and performance. The contract is governed by Ontario law, and all bids must comply with mandatory technical and procedural requirements including submission of manufacturer details, compliance with packaging and marking standards per Canadian Forces Specifications D-LM-008-036/SF-000 and D2000C/D2001C, and application of UCC/EAN-128 barcodes using Application Identifiers 241 for PSCN or 7001 for NSN with human-readable interpretation beneath. Packaging must be one unit per package, with wood and palletization conforming to SACC Manuals D2025C and D6010C respectively. All items must be delivered delivered duty paid (DDP) to the specified locations by March 31, 2027, with delivery and invoicing codes outlined in Annex A and its appendices. Bids must be structured in three distinct sections—technical, financial, and certifications—with prices included only in the financial section. The evaluation is based on the lowest evaluated price per item, subject to compliance with mandatory pass/fail gates including solicitation adherence, technical requirements, and correct part and NCAGE identification. A Canadian content certification is conditionally required; if two or more non-affiliated bidders submit valid certifications, only those bids are eligible for award. Bidders must also provide a Declaration of Convicted Offences and maintain continuous compliance with all submitted certifications throughout the contract term, with Canada retaining the right to verify them at any time. Invoicing must follow strict guidelines, with physical copies sent
Department of National Defence

POSTED

5 days ago

DEADLINE

in 9 days
View Details
NAICS: 333414
New
DIBBS
GRILLE, METALThe contract is for the procurement of a metal grille identified by NSN 4130-01-649-3038 and part number 178K0365-1-SV, with a quantity of nine units to be delivered under solicitation SPE8E8-26-T-4693. Delivery is required within 176 days of contract award, with FOB origin terms and no variance allowed in quantity. Inspection and acceptance occur at the destination, and the items must be packaged according to ASTM D3951 unless superseded by any DLA Master List of Technical and Quality Requirements, which take precedence. Packaging and labeling must comply with MIL-STD-129, and palletization must follow DLA Packaging Requirements. The designated delivery address is the DDSP New Cumberland Facility in New Cumberland, Pennsylvania, and the required ship date is January 13, 2027, with the original delivery deadline set for January 26, 2027. The contract references specific DLA procedural notes for transportation and includes requirements for removal of government identification from non-accepted supplies and potential application of covered defense information protocols. The unit of issue is each, with a unit price of $9.00 and a total contract value of $81.00. All technical and quality specifications are governed by the DLA Master List, with the applicable revision determined by the solicitation or award date depending on acquisition size.
DDSP NEW CUMBERLAND FACILITY

POSTED

5 days ago

DEADLINE

in 7 days
View Details