SORBENT, HAZARDOUS MATERIAL

SORBENT, HAZARDOUS MATERIAL . . RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
"SDS AND OSHA HAZARD WARNING/PRODUCT LABEL (HWL) ARE REQUIRED. THE SDS AND HAZARD WARNING LABEL MUST BE REVIEWED AND APPROVED BY CHEMISTS/TECHNICAL PERSONNEL BEFORE CONTRACT AWARD. THE APPROVED SDS AND LABEL MUST THEN BE PLACED IN THE CONTRACT FILE AND A COPY FORWARDED TO THE DLA AVIATION HMIRS OFFICE (VBA)."
Hazard Communication Standard Notice:
Effective June 1, 2015, Federal Standard No. 313-E, Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities, establishes the requirement for preparation and submission of Safety Data Sheets (SDS) in lieu of Material Safety Data Sheets (MSDS) by suppliers who provide hazardous materials to government activities.
The Occupational Safety and Health Administration (OSHA) has modified its Hazard Communication Standard (HCS) to conform to the United Nations Globally Harmonized System of Classification and Labeling of Chemicals. As a result of this change, GSA revised Federal Standard No. 313-E requiring Safety Data Sheets for classifying chemicals and communicating the applicable information on labels.
In accordance with the revised standard after June 1, 2015:
1. Suppliers will be required to submit, to the contracting officer for
SPE4A7-27-R-X018
SECTION B
SUPPLY/SERVICE: 4235-01-528-0401 CONT'D
review and approval prior to award, safety data sheets consistent with the requirements found at 29 C.F.R. 1910.1200 for hazardous materials delivered to the Government.
2. Suppliers will also be required to submit, to the contracting officer for review and approval prior to award, Hazardous Communication Standard (HCS) labels in accordance with 29 C.F.R. 1910.1200 requirements or current Consumer Product Safety Act (CPSA), Federal Hazardous Substance Act (FHSA) labels when subject to labeling requirements under those statutes. This product labeling is required for hazardous materials delivered to the Government.
3. Finally, suppliers must train their employees on the new safety data sheets, hazardous communication labels, and requirements of 29 C.F.R. 1910.1200.
For more information on SDS, refer to OSHAs website, available at:
https://www.osha.gov/law-regs.html
For information on 29 C.F.R. 1910.1200, refer to the below link:
https://www.osha.gov/dsg/hazcom/index.html
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL OF A TYPE')
THIS MATERIAL DOES NOT HAVE A SHELF LIFE REQUIREMENT
UNIT OF ISSUE = BAG (BG), ONE BG CONTAINS 50.0 LBS (22.68 KG)
I/A/W CID A-A-59759 TYPE I
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC CID A-A-59759A NOT 1 REVISION NR A DTD 02/18/2025 PART PIECE NUMBER: A-A-59759 TYPE I
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments%2FDLMS% 2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT. 0001 4235-01-528-0401 2,210.000 BG $ _______________ $ ______________ SORBENT,HAZARDOUS MATERIAL
PRICING TERMS: Firm Fixed Price
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
FOB: ORIGIN DELIVERY DATE: 30 DAYS ADO
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:10 OPI:M
SPE4A7-27-R-X018
SECTION B
SUPPLY/SERVICE: 4235-01-528-0401 CONT'D
PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
SUPPLEMENTAL PACKAGING DATA: UNIT OF ISSUE BG=50LB
PARCEL POST ADDRESS:
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
GOVT USE External External External Customer RDD/ ITEM PR PRLI PR PRLI Material Need Ship Date. 0001 1000240483 0001 N/A N/A N/A N/A

SPE4A7-27-R-X018 NSN/Part Number: 4235-01-528-0401 Quantity: 2,210 BG Delivery: 30 days ADO