Stinger Guided Missile, Intercept-Aerial (GMIA)/Captive Flight Trainer (CFT) Test Set (TE 600);

The United States Government is conducting market research to determine if there are potential sources with the capability to provide one (1) unit, a single Stinger Guided Missile, Intercept- Aerial (GMIA)/Captive Flight Trainer (CFT) Test Set. Referred to as a TE600 equivalent test set, this will meet the requirements of drawing 2861462, used to build TP403691, the existing TE600 equivalent test set at McAlester Army Ammunition Plant (MCAAP). STINGER OVERVIEW The Stinger Block I missile is an advanced, "fire-and-forget", short-range, man-portable, air defense weapon system. It provides low-altitude defense for ground forces against attack or aerial observation by low-flying Unmanned Aerial System (UAS), Cruise Missile, Rotary Wing, and Fixed-Wing threats. The missile utilizes a high explosive, hit-to-kill warhead. Stinger can be fired from the shoulder or from a variety of platforms to include vehicles, helicopters and UAS. Optical Alignment Test Equipment (TE) 600 The function of the GMIA/CFT Test Set, TE600 is to provide additional means to test missiles in support of the Stinger Service Life Extension Program (SLEP), Stockpile Reliability Program (SRP), and other efforts. The TE600, known as a weapon test set is a system that operates on Stinger "Guided Missile, Intercept-Aerial" (GMIA) of various configurations (92E, 92F, 92H, etc.). The test set provides the means to demonstrate/prove that the GMIA functions in accordance with the performance specification. The test set is described as an assemblage of various sub-systems including weapon cooling system/coolant flow measurement, target motion control (look angle system), target system, gyro measurement, boresight detection, tracking detection, and weapon transducer measurement. Other sub-systems include power, safety interlock sensing, and weapon control functions. The test set should also be capable of testing missile trainers, i.e. CFTs. The GMIA/CFT Test Set, TE600 Top Assembly Drawing (TAD) is 13044885. There have been modifications applied to the TE600 since drawing 13044885. However, the Government does not own any modified drawings. In accordance with Federal Acquisition Regulation (FAR) 15.201 (e), responses to this notice are not an offer and cannot be accepted by the Government to form a binding contract. The Government will not pay for information received. The Government points of contact are Nicholas Kirby and Richard Kolodzne at: nicholas.b.kirby.civ@mail.mil richard.a.kolodzne.civ@mail.mil Per FAR 52.215-3, Request for Information or Solicitation for Planning Purposes: The Government will not pay for the information solicited except as an allowable cost under other contracts as provided in subsection 31.205-18, bid and proposal costs, of the FAR. Although "proposal" and "offeror" are used in this RFI, your response will be treated as information only. It shall not be used as a proposal. This RFI is for planning and market research purposes only and should not be considered as a request for proposals or as a solicitation to do business with the Government. The contractor shall provide a total quantity of 1 (one) GMIA/CFT Test Set, TE 600. The contractor shall furnish all services, materials, facilities and equipment and provide all technical, planning, and managing efforts needed to produce the item. RESPONSE INSTRUCTIONS Part A. Business Information: Please provide the following information for your company/institution and for any teaming or joint venture partners: Company/Institute name Address Point of Contact Cage Code DUNS Number Phone Number E-mail Address Web page URL Size of business pursuant to North American Industry Classification System (NAICS) Code 334519. Based on the above NAICS Code, state whether your company qualifies as a: Small Business (Yes/No) Woman Owned Small Business (Yes/No) Small Disadvantaged Business (Yes/No) 8(a) Certified (Yes/No) HUB Zone Certified (Yes/No) Veteran Owned Small Business (Yes/No) Service Disabled Small Business (Yes/No) Central Contractor Registration (Yes/No) Statement describing company as domestically or foreign owned (if foreign owned, please indicate country of ownership). Part B. Capability: Describe briefly the capabilities of your company and the nature of the goods and/or services you provide. Include a description of your staff composition and management structure. Describe your company's past experience (no more than five examples) on previous projects similar in complexity to this requirement. Include contract numbers, a brief description of the work performed, period of performance, agency/organization supported, and individual points of contact (Contracting Officer or Program Manager). If you were to rely on subcontractors for this effort, what subcontractors would you use to do what percentage of which portions? What are their experiences and do you already have a relationship with the subcontractor(s)? Describe your company's approach and capabilities in obtaining and retaining qualified and experienced personnel. How soon could your company secure qualified personnel? Part C. Financial Capability: Describe your financial capabilities to successfully perform this contract. Describe any other relevant topics, concerns, and information that will help the Government in forming an acquisition strategy. SUBMISSION INSTRUCTIONS: Respondents should indicate which portions of their responses are proprietary and should mark them accordingly. Marketing material is considered an insufficient response to this RFI. Please limit responses to no more than 20 pages. Response must include Company name, Commercial and Government Entity (CAGE) code, classified mailing address, and appropriate point of contact information. Responses may be emailed to the USG POCs identified herein.