TANK, PRESSURE

TANK,PRESSURE
TANK,PRESSURE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
CONTRACTOR FAT REQUIRED PER QAP 7411078. ADDITIONAL TESTING PER QAP AND
DRAWING 7411078.
FULL AND OPEN COMPETITION APPLY
This material has specialty metal requirements. DFARS 252.225-7008,
SPE7L3-27-T-1959
SECTION B
DFARS 252.225-7009, and DFARS 252.225-7010 apply to this award if over the Simplified Acquisition Threshold.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
THE ITEM DESCRIBED IN THIS SOLICITATION
IS DEFINED IN WHOLE OR IN PART BY ARMY
DRAWING(S). THESE DRAWING(S) MAY CONTAIN
A PAINT FINISHING REQUIREMENT. WHERE SUCH
REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING
16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE
MENTS OF THE ARMY DRAWING(S). THIS DRAWING
CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT
RESISTANT COATINGS (CARC), AND ADDITIONAL
INFORMATION RELATING TO HIGH TEMPERATURE
COATINGS.
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
MANUFACTURERS LIST (QML)" APPLY.
RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for Manufacturers and Non-Manufacturers
"ANY ITEM PREVIOUSLY TESTED BY A VENDOR
IN ACCORDANCE WITH QUALIFICATION
REQUIREMENTS (FOR EXAMPLE: FAT, HIGH
SHOCK AND/OR VIBRATION TEST), STATED ON
DWG, SPECIFICATION, OR STANDARD MAY NOT
REQUIRE FURTHER TESTING BY THE SAME VENDOR
EXCEPT FOR A LATER CHANGE IN DESIGN,
MANUFACTURING PROCEDURES, OR TESTING
REQUIREMENTS. A CERTIFICATION OF
CONFORMANCE WITH PREVIOUS TEST RESULTS
ATTESTING APPLICABILITY SHALL BE
SUBMITTED FOR ITEMS PREVIOUSLY TESTED."
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC DRAWING NR 19207 7411078 REVISION NR M DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8380811 REVISION NR D DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8764677 REVISION NR F DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 11684435 REVISION NR A DTD 05/19/1987 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12355846
SPE7L3-27-T-1959
SECTION B
REVISION NR F DTD 04/04/2007
PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12461890 REVISION NR B DTD 05/01/2023 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 7411078 REVISION NR J DTD 01/17/1983 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8380799 REVISION NR H DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8380808 REVISION NR E DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8735500 REVISION NR G DTD PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8380804 REVISION NR H DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12461890 REVISION NR B DTD 05/01/2023 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12355846 REVISION NR F DTD 04/04/2007 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 3830810 REVISION NR H DTD 03/10/2011 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 7411078 REVISION NR A DTD 05/17/1973 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 7411078 REVISION NR DTD 01/21/2026 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8380810 REVISION NR H DTD 03/10/2011 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
SPE7L3-27-T-1959
SECTION B
PR: 7019021805 PRLI: 0001 CONT’D
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7019021805 0001 EA 23.000
NSN/MATERIAL:2530007411078
DELIVERY (IN DAYS):0273
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA-QUP:001
IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313,
PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025.
IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH
FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE
WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:05/04/2027 Original Required Delivery Date:03/13/2028
SPE7L3-27-T-1959
SECTION B
PR: 7019021805 PRLI: 0001 CONT’D

CONTRACTOR FIRST ARTICLE TEST THE NUMBER OF UNITS SHOWN SIGNIFIES THE
TEST REQUIREMENT. SEE FAR CLAUSE 52.209-3 CITED IN SECTION A OF THIS
SOLICITATION FOR THE ACTUAL QUANTITY REQUIRED.
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0002 0000000000 EA 1.000
NSN/MATERIAL:0001S00000053
DELIVERY (IN DAYS):0090
THIS LINE ITEM SIGNIFIES THE FIRST ARTICLE TEST REQUIREMENT (FAT). SEE
CLAUSES FOR INFORMATION CONCERNING THE FAT REQUIREMENT. OFFERS THAT DO
NOT CITE A PRICE FOR THIS LINE ITEM SHALL BE EVALUATED UNDER THE
ASSUMPTION THAT THERE IS NO SEPARATE CHARGE FOR THE FAT. IN THE EVENT
THE FAT REQUIREMENT IS WAIVED, NO AWARD WILL BE MADE FOR THIS LINE ITEM.
THE NUMBER OF UNITS SHOWN APPEARS AS “1 EA”. THIS QUANTITY SIGNIFIES
THE TEST REQUIREMENT. OFFERORS WILL FIND THE ACTUAL QUANTITY REQUIRED
BY THE GOVERNMENT FOR THE FAT LINE ITEM PER FAR 52.209-3 OR 52.209-4 IN
SECTION A OF THIS SOLICITATION.
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000
SPE7L3-27-T-1959 NSN/Part Number: 2530-00-741-1078 Quantity: 23 EA Purchase Request: 7019021805QTY: 23 Delivery: 273 days ADO