TURBO SUPERCHARGER, ENG

TURBO SUPERCHARGER,ENGINE,NON-AIRCRAFT
TURBO SUPERCHARGER,ENGINE,NON-AIRCRAFT
RESTRICTION ON THE ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011)
AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING
MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR
EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (ROLLING
ELEMENTS, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE
UNITED STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE
TOTAL COST OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE
DFARS CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER
BEARINGS.
A CONTRACTOR’S DECLARATION ON THE DOMESTIC/FOREIGN NATURE OF MATERIAL
BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN BEARING WEBSITE AT
https://www.dla.mil/Aviation/Business/Foreign-Bearing-Waiver/. TO OBTAIN A COPY OF THE CONTRACTOR’S DECLARATION. PLEASE PRINT, COMPLETE, SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING CONSIDERD FOR AWARD.
IN THE EVENT NO OFFERED BEARINGS MEET THIS SOURCING REQUIREMENT, THIS SOLICITATION MAY BE CANCELLED OR HELD PENDING A WAIVER APPROVAL REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN APPROVED WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT MAY BE RE-SOLICITED OR BUYER MAY REQUEST A QUOTE EXTENSION. SEE DFARS 225.7009-4, WAIVER, RESTRICTION ON BALL AND ROLLER BEARINGS. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RT001: MEASURING AND TEST EQUIPMENT
THIS IS A SOURCE CONTROLLED ITEM WHICH MUST BE
SPE4A7-26-T-765T
SECTION B
MANUFACTURED AND TESTED IN ACCORDANCE WITH THE
CITED LIMITED RIGHTS DATA. THE GOVERNMENT CAN
NOT PROVIDE THE DATA. ONLY THOSE VENDORS WHO
HAVE ACCESS TO THE DATA OR CAN PROVIDE TRACE
ABILITY TO THE APPROVED SOURCES SHOULD QUOTE.
SAR PACKAGE IS REQUIRED IF YOUR COMPANY IS
CONSIDERING SOURCE APPROVAL.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
GM DEFENSE LLC 97DN1 P/N 40009097
TDP Rev A Gen 1 IAW BASIC DRAWING NR 1X4F3 AMSCBDOC REVISION NR DTD 03/07/2007 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 13873 40009097 REVISION NR DTD 07/15/2025 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018379245 0001 EA 9.000
NSN/MATERIAL:2950017310993
DELIVERY (IN DAYS):0148
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z
SPE4A7-26-T-765T
SECTION B
PR: 7018379245 PRLI: 0001 CONT’D
UNIT CONT:ZZ OPI:M
INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PACKAGING SHALL BE IAW DWG 40009097 SPI# AK17310993 REV "A" DTD 07/15/2025.
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:02/21/2027 Original Required Delivery Date:02/21/2027
SPE4A7-26-T-765T NSN/Part Number: 2950-01-731-0993 Quantity: 9 EA Purchase Request: 7018379245QTY: 9 Delivery: 148 days ADO