Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, December 9 at 2:00 PM ET

Register Free →

This Solicitation opportunity from Department Of Defense was posted on September 24, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.

WASHER

Closed
SPE4A6-26-T-36PQFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

Active Opportunities Like This One

AI Contract Overview

Show more

Solicitation SPE4A6-26-T-36PQ, issued by the DLA Aviation ASC Commodities Division, seeks quotes for 400 units of washers under NSN 5310-01-665-6150. The required delivery date is May 15, 2027, with a need ship date of December 1, 2026, to the DLA Distribution DDSP New Cumberland Facility in Pennsylvania. Delivery is required within 59 days after receipt of order. Quotes must be submitted via the DIBBS system by October 2, 2026. Inspection and acceptance will occur at the destination, and the contractor must use the Wide Area WorkFlow system for electronic invoicing and payment. The contract mandates strict adherence to technical and quality requirements, including packaging per ASTM D3951 and MIL-STD-129, and palletization according to RP001. Key security and regulatory requirements include CMMC Level 2 Self-Assessment, safeguarding of covered defense information per DFARS 252.204-7012, and compliance with ITAR or EAR export controls. Additionally, offerors must comply with the Buy American Act and the Berry Amendment. Parts produced via additive manufacturing are prohibited unless specifically authorized.

General Info

DLA seeks quotes for 400 washers by October 2, 2026, for May 2027.

NAICS

332722 - Bolt, Nut, Screw, Rivet, and Washer Manufacturing

Place of Performance

2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, USA

Set-Aside

NONE

Documents

1
PDF, High priority: read this first18 pages · rfq
High

Read the document

Every page of every file, in your free workspace.

Read the document

AI Contract Breakdown

Uniform Contract Format

Sign up to view the full breakdown with detailed analysis of each section.

View Full Breakdown

This one is closed. Find the next one like it.

Open contracts like this one, right now:

  • Supply of Retaining Clips (NSN 5340016706441)Open now, due in 15 days
  • Precision Manufacture of Flat Washers (NSN 5310-01-733-7584)Open now, due in 7 days
See open contracts like this

Ask CLEATUS

I've read this contract. Ask me anything.

Timeline

PhaseClosed
Posted

Solicitation

Response Deadline

Deadline has passed

Submission Closed

Find active opportunities like this

Get full access to discover similar active contracts, track opportunities, and build proposals with AI assistance.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC COMMODITIES DIVISION
Contacts1 person available
OfficeUSA

Full Description

Show more
WASHER
WASHER
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RD004: Cybersecurity Maturity Model Certification (CMMC) Level 2 Self-Assessment RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 5310-01-665-6150 Quantity: 400 EA Purchase Request: 7018306027QTY: 400 Delivery: 59 days ADO

More opportunities from Department Of Defense → ASC COMMODITIES DIVISION

Same awarding agency

NAICS: 332722
New
DIBBS
STUD, WELDING
Solicitation # SPE4A6-26-T-58E7
Solicitation SPE4A6-26-T-58E7 is a small business set-aside procurement issued by the DLA Aviation ASC Commodities Division for the supply of five welding studs, identified by NSN 5307-01-730-9774. The contract is managed under the First Destination Transportation program with a delivery requirement of 148 days after order, with a need ship date of October 18, 2026, and a final delivery date of January 17, 2027. Delivery is designated as FOB Destination Other, with the consignee located at the DLA Distribution DDSP New Cumberland facility in Pennsylvania. The procurement is subject to strict technical and quality requirements, including a prohibition on additive manufacturing unless specifically authorized. Quality assurance is governed by MIL-STD-1916 or ASQ H1331, with a zero-non-conformance acceptance criteria for sample lots. Inspection and acceptance are both required at the origin, and manufacturers must maintain an inspection system complying with SAE AS9003 or ISO 9001. Packaging and marking must adhere to MIL-STD-2073-1E and MIL-STD-129. The contract includes significant regulatory requirements, including export controls under ITAR and EAR, and requires contractors to have an approved US/Canada Joint Certification Program certification to access technical data. It incorporates various FAR and DFARS clauses regarding equal opportunity, combating trafficking in persons, and domestic material restrictions such as the Berry Amendment and Buy American Act. Administrative processing and invoicing must be conducted through the Wide Area WorkFlow system.
Bolt, Nut, Screw, Rivet, and Washer Manufacturing

POSTED

1 day ago

DEADLINE

in 2 days
View Details

Earlier notices in this NAICS code

Posted before this notice, open and closed

Find Active Opportunities Like This

Get AI-powered intelligence on the opportunities still open

Every page of the solicitation package shredded into a compliance breakdown

AI-powered matching based on your capabilities and past performance

Competitor and incumbent history on the requirement

Automated alerts on amendments, Q&A deadlines, and award

Miguel
Hillary
Keith Deutsch
Christine

Join 750+ contractors already using CLEATUS