GAGE, TIRE PRESSURE,

GAGE,TIRE PRESSURE,
GAGE, TIRE PRESSURE.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
THE INFLATION RANGE IS: 10 160 PSIG DUAL-CHUCK, STANDARD BORE<(>,<)>
LONG EXTENSION, EXTERNAL INDICATING. PER
COMMERCIAL ITEM DESCRIPTION TITLED "GAGES, TIRE
PRESSURE, SELF CONTAINED AND INFLATOR GAGE<(>,<)>
PNEUMATIC TIRE."
AMPLIFICATION OF PARAGRAPH 3.2: "THE INDICATOR
BAR SHALL BE NOT LESS THAN .250 INCHES SQUARE<(>,<)>
CALIBRATED (MARKED GRADUATIONS) ON ALL FOUR
SIDES. TWO OPPOSITE SIDES OF THE INDICATOR BAR
SHALL BE MARKED IN INCH-POUND UNITS OF LBS PER
SQUARE INCH & THE ALTERNATE TWO SIDES SHALL BE
MARKED IN THE INTERNATIONAL SYSTEM OF UNITS PER
ASTM E380. THE METRIC MARKINGS SHALL BE IN
UNITS OF KILOPASCAL (KPA). THE INCH-POUND
MARKINGS SHALL BE IN 2 PSI INCREMENTS WITH
NUMERIC MARKINGS EVERY 10 PSI, READING FROM 10
TO 160 PSIG (160 NEAR THE BARREL AND 10 NEAR THE
SPE7LX-26-U-9226
SECTION B
EXTENDED FAR END OF THE INDICATOR BAR; NUMERALS
TO READ UPRIGHT WHEN GAGE IS HELD WITH THE DUAL
CHUCK AT THE TOP). THE SI MARKINGS SHALL BE
GRADUATED IN 20 KPA INCREMENTS WITH NUMERIC
MARKINGS EVERY 100 KPA, READING FROM 80 TO 1100
KPA MINIMUM RANGE. THE INCH-POUND MARKINGS
SHALL BE IN BLACK AND THE SI MARKINGS IN RED."
CORROSION RESISTANT MATERIAL SHALL BE
EITHER STAINLESS STEEL OR BRASS.
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC CID A-A-59568A NOT 2 REVISION NR A DTD 09/18/2023 PART PIECE NUMBER: AA59568-002-B-3
TDP Rev A Gen 1 IAW REFERENCE STD NR MIL-STD-129R(3) REVISION NR R DTD 02/25/2023 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE CID A-A-59564A NOT 1 REVISION NR A DTD 07/23/2024 PART PIECE NUMBER: AA59568-2B3
LINE ITEM 0000000001 TYPE OF COVERAGE: DLA DIRECT, CONUS
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 1000238666 0001 EA 1,187.000
This is an estimated quantity and may not be purchased by the IDC.
NSN/MATERIAL:4910002043170
DELIVERY (IN DAYS):0116
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00 WRAP MAT:CA CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:D3 OPI:O INTRMDTE CONT:DO INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING
SPE7LX-26-U-9226
SECTION B
PR: 1000238666 PRLI: 0001 CONT’D
REQUIREMENTS FOR PROCUREMENT
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.

SPE7LX-26-U-9226 NSN/Part Number: 4910-00-204-3170 Quantity: 1,187 EA Purchase Request: 1000238666QTY: 1187 Delivery: 116 days ADO