This Award Notice opportunity from Department Of Defense was posted on September 29, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
Bldg. 1025 HVAC at Kirtland AFB
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This contract was awarded as an 8(a) Sole Source Set-Aside to provide all necessary parts, labor, and equipment for HVAC improvements at Building 1025 at Kirtland Air Force Base. The scope of work focuses on the installation of a specialized exhaust system for air compressor heat exhausts, including detachable duct hoods, a high-capacity wall-mounted exhaust fan rated for 140 degree Fahrenheit air, and motorized control dampers. The project requires precise ductwork construction meeting SMACNA standards and the integration of automated controls to ensure the exhaust fan and dampers operate in synchronization with the compressors. Additionally, the contractor is responsible for installing a 3-ton wall-mounted mini split air conditioning unit with a high ambient kit to cool the mechanical room. The work includes routing refrigerant lines, managing condensate drainage, and ensuring all electrical installations comply with NEC and UFC standards. Strict site constraints are in place, requiring the contractor to be escorted at all times and prohibiting any new penetrations or equipment mounting on the North and East walls of the mechanical room.
General Info
Contract Value
$207,214Place of Performance
Set-Aside
Awardee
COLT BUILDERS INCAward Issued Date
Documents
0No documents available
This contract was awarded without public documents.
AI Contract Breakdown
Uniform Contract FormatNo documents to break down
The breakdown needs solicitation documents. None were found from this contract's source.
This one is closed. Find the next one like it.
Open contracts like this one, right now:
- Install Pier D High Pressure Air System, NSBREM-724-AOpen now, due in 11 days
- Springdale JCC –Recreation HVAC Repair or ReplacementOpen now, due in 20 days
Ask CLEATUS
I've read this contract. Ask me anything.
Timeline
Award Notice
Contract was awarded
Organization & Contact Information
Full Description
This action was awarded as an 8(a) Sole Source Set-Aside under the authority of section 8(a) of the Small Business Act.
The contractor shall furnish all parts, material, labor, equipment and supervision necessary to complete the work for Building 1025 HVAC.
- Construction
- Contractor to provide and install an 8.5”x20.5” duct hood over the air compressor heat exhausts that transition to 14” ø round duct. Duct hood must be detachable to allow for the removal of the compressor top plate for maintenance.
- Contractor to remove SF-1 and wall louver. Expand existing 12”x18” wall penetration to 18”x18” penetration on the South wall.
- Install wall mounted exhaust fan rated for 1500 CFM @ 1” W.C. with using single phase 208V with soft start motor. Fan and motor must be rated to handle 140°F exhaust air. Provide 18”x18” ducted exhaust plenum 2’ into the mechanical room.
- Route 14”ø duct from each compressor into the 18”x18” plenum. Utilize conical fittings for branch take-offs and 30° minimum rectangular to round transitions and 1.5D round elbows.
- Provide gasketed low leakage motorized control dampers on each 14”ø duct between the hood and the exhaust plenum.
- Contractor to provide a 3-ton (36,000 BTU/hr) wall mounted mini split air conditioning unit on west wall above the compressed air desiccant driers. Mount wall mounted unit on available space without moving existing compressed air piping or conduit. Secure unit to wall per manufacturer instructions. Route condensate to nearest floor sink. Terminate condensate pipe above floor sink rim. Size per manufacturer requirements.
- Contractor to provide mini split condensing unit with high ambient kit by the same manufacturer. Locate exterior unit between stairs to electrical room and mechanical room. Secure unit to the ground per manufacturer instructions or mounted on C-channel with concrete anchors. Mini split must be 208V single phase.
- Contractor to provide and install refrigerant line sets between mini split per manufacturer instructions. Flash and seal new penetration for line set.
- Provide controls for equipment as follows: Exhaust fan must start when either compressor activates. Fan must remain on for at least 5 minutes (adjustable up to at least 15 minutes) after compressor turns off. Motorized control dampers must open when associated air compressor is activated. Damper must stay open until the exhaust fan turns off. Provide duct access panel for each damper on the bottom of the duct. Provide thermostat for new mini split. Set temperature to 85°F (adjustable).
- All new duct and duct connections shall be sealed to Class A and hung from the structure or mechanical room walls (where allowed) per SMACNA HVAC Duct Construction Standards.
- Provide 1in. W.C. Duct Pressure Classification on all exhaust duct systems, provide a minimum 22 Ga. Galvanized sheet metal meeting ASTM A924/A924M and ASTM A653/653M for all exhaust duct as indicated on the supplemental drawings.
- Provide power to the new exhaust fan and motorized control dampers from Panel P1. Reuse of conduit from demolished supply fan is acceptable provided it meets all NEC requirements. Provide power to mini split air conditioner from panel LM1. All wiring must be provided per NEC. Provide disconnects to exhaust fan, condensing unit and indoor unit per UFC 3-410-01.
- Contractor will need to be escorted at all times with the construction schedule coordinated with the facility user.
- All new penetrations between the electrical and mechanical rooms must be sealed with fire caulk.
- The North and East walls in the Mechanical Room cannot have any new penetration or be utilized to mount hang or hang any new equipment.
More opportunities from Department Of Defense → W075 Endist Albuquerque
Same awarding agency
Get AI-powered intelligence on the opportunities still open
Every solicitation package arrives shredded into a compliance breakdown and matched to your past performance, with incumbent history and alerts on amendments and award.
Join 900+ contractors already using CLEATUS
