Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, August 19 at 2:00 PM EDT

Register Free →
logo
Get CLEATUS

BOLT ASSY, HYDRAULIC

Active
SPE4A7-26-T-637ZFederal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

Show more

The contract pertains to the procurement of two hydraulic bolt assemblies with part number ABC6094 and NSN 1650-00-549-3578, sourced from MONOGRAM AEROSPACE FASTENERS with CAGE code 98524. Delivery is required within 20 days after order date, with the solicitation issued under SPE4A7-26-T-637Z and a response deadline of August 18, 2026. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, with revisions controlled by the solicitation issue date for simplified acquisitions or the RFP issue date for large acquisitions, subject to amendments. Comprehensive documentation is mandated, including a Source Approval Request with full data packages for both approved and alternate parts, since no existing data is available. Quality assurance is enforced through tailored higher-level requirements, inspection and acceptance at origin, and mandatory removal of government identification from non-accepted items. Physical marking of bare items is required, along with compliance to DLA packaging standards and Cybersecurity Maturity Model Certification Level 2 self-assessment. Sampling must adhere to MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances permitted, unless otherwise specified, with attributes classified per critical, major, or minor designations corresponding to verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0. Measuring and test equipment must be properly calibrated and documented. The contract enforces Covered Defense Information security protocols and is managed by the Department of Defense through the ASC Supplier Oper AE and AF Division, with primary point of contact provided for inquiries.

General Info

Procure two hydraulic bolt assemblies, deliver in 20 days, comply with DLA quality, packaging, cybersecurity CMMC L2, and zero-defect sampling standards.

Agency

Department Of Defense → ASC SUPPLIER OPER AE AND AF DIVView Agency

NAICS

336413 - Other Aircraft Parts and Auxiliary Equipment ManufacturingView NAICS

Place of Performance

USA

Set-Aside

NONE

Documents

(0)

No documents available

AI Contract Breakdown

Uniform Contract Format

No contract breakdown available.

Cannot generate Contract Breakdown because no documents were found from this contract's source.

Timeline

PhaseSolicitation
Posted

Solicitation

Response Deadline

Submission deadline

Response Deadline

Ready to pursue this opportunity?

Start your free trial to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC SUPPLIER OPER AE AND AF DIV
Contacts1 person available
OfficeUSA
Organization / Agency
Department Of Defense → ASC SUPPLIER OPER AE AND AF DIV
View Agency Profile
Office AddressUSA
Contacts
JAHAIDA HALL HUDSON
contact@example.gov
+1 (555) 000-0000

Full Description

Show more
BOLT ASSY,HYDRAULIC
BOLT ASSEMBLY, HYDRAULIC.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RD002, COVERED DEFENSE INFORMATION APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RD004: Cybersecurity Maturity Model Certification (CMMC) Level 2 Self-Assessment
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RT001: MEASURING AND TEST EQUIPMENT
MONOGRAM AEROSPACE FASTENERS, CAGE 98524
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
SPE4A7-26-T-637Z
SECTION B
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
P/N ABC6094
IDENTIFY TO:
SAMPLING:
NO DATA IS AVAILABLE. THE ALTERNATE OFFEROR IS
REQUIRED TO PROVIDE A COMPLETE DATA PACKAGE
INCLUDING DATA FOR THE APPROVED AND ALTERNATE
PART FOR NSN/Part Number: 1650-00-549-3578 Quantity: 2 EA Purchase Request: 7017756226QTY: 2 Delivery: 20 days ADO

Similar Contracts

Same NAICS industry code

NAICS: 336413
New
Federal
Shotover ARS Airborne Surveillance mapping system - 2026-SG-0024The contract pertains to the Shotover Augmented Reality Mapping system designed for airborne surveillance, currently deployed alongside DEA airborne imaging systems. This advanced system enhances situational awareness by overlaying critical mission information such as street names, addresses, parcel data, business names, and landmarks directly onto live video feeds. It serves to bolster ground-based enforcement by providing recorded video evidence, improving the efficacy and precision of surveillance operations. Issued by the Drug Enforcement Administration under the Department of Justice, this contract is identified as "Shotover ARS Airborne Surveillance mapping system - 2026-SG-0024" and falls under the NAICS code 336413. Although certain logistical details such as solicitation number and exact place of performance are not specified, the contract emphasizes support for small businesses through a dedicated point of contact within the DEA Small Business Program. The system’s deployment indicates an ongoing effort to integrate cutting-edge technology into law enforcement surveillance capabilities.
Drug Enforcement Administration

POSTED

about 13 hours ago

DEADLINE

N/A
View Details
NAICS: 336413
New
DIBBS
Supply of Cross-Tube Component (NSN 1560-LL-NC0-1153)The contract seeks the manufacture or supply of two units of a cross-tube component identified by part number 205-030-104-005 and national stock number 1560-LL-NC0-1153, to meet the technical specifications established by Bell Textron and the Defense Logistics Agency. The component is critical for defense applications and must adhere to exacting quality and performance standards set by these entities. The place of performance is designated as Cherry Point, North Carolina, with a zip code of 28533-0021, indicating the operational location where the delivered parts will be managed or integrated. The contract is classified as a subcontract under NAICS code 336413, which corresponds to aircraft parts and auxiliary equipment manufacturing. The solicitation was posted on August 10, 2026, with a firm response deadline of August 18, 2026, giving potential suppliers a limited window of eight days to submit proposals. The responsible agency is the DLA Fleet Readiness Center under the Department of Defense, which oversees logistics and maintenance support for military equipment. Although no specific point of contact or set-aside details are provided, the procurement is part of the broader DLA procurement system, managed through the DIBBS platform, and interested parties must access the official UI link to obtain full submission requirements and technical documentation. Timely and compliant responses are essential to meet operational readiness timelines.
DLA FLEET READINESS CENTER DLA PSC

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336413
New
DIBBS
FORMER, AIRCRAFT
Solicitation # SPE4A6-26-T-14VJ
ASC COMMODITIES DIVISION

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336413
New
DIBBS
PULLEY, GROOVE
Solicitation # SPE7M4-26-T-328R
The contract calls for the procurement of 2,405 Pulley, Groove units identified by NSN 3020002771123, designated as a critical application item and classified as a commercial item. The part must conform to MS20220-2 and be manufactured in strict compliance with MIL-DTL-7034/2B, MIL-DTL-7034/1B, and MIL-DTL-7034F(2) specifications, excluding revision 3, as well as referenced drawing 98752 200415485 and applicable general engineering notes 1, 3, and 12. The item is subject to the Qualified Products List or Qualified Manufacturers List, requiring manufacturer qualification prior to award. Technical and quality requirements from the DLA Master List of Technical and Quality Requirements, identified by R or I numbers, take precedence over all other standards. Sampling must follow MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based plan, with critical, major, and minor attributes assigned verification levels VII, IV, and III or AQLs of 0.1, 1.0, and 4.0, respectively; unspecified attributes default to major. All items must be packaged per ASTM D3951, but DLA requirements override this standard; palletization must adhere to RP001, and all packaging must be marked and labeled in accordance with MIL-STD-129, including specific labeling for hazardous materials under 29 CFR 1910.1200 and radioactive materials exceeding defined thresholds. The contract mandates full compliance with DFARS and FAR clauses regarding cybersecurity, including NIST SP 800-171 assessment requirements, safeguarding covered defense information, and prohibitions on hexavalent chromium, covered telecommunications equipment, and communist Chinese military company items. The item is to be delivered FOB Origin to Tinker AFB, Oklahoma, with inspection and acceptance occurring at destination after a 164-day delivery window. Payment must be submitted electronically via WAWF, with strict adherence to electronic invoicing and receiving report protocols. The solicitation is a HUBZone set-aside requiring offerors to submit representations on small business, WOSB, and HUBZone status, and to certify compliance with whistleblower rights, anti-trafficking,
FLUID HANDLING DIVISION

POSTED

about 18 hours ago

DEADLINE

in 10 days
View Details
NAICS: 336413
New
DIBBS
COIL ASSEMBLY, EXCHA
Solicitation # SPE4A6-26-T-14VT
The contract pertains to the procurement of a single coil assembly for an exchanger with NSN and part number 1650-01-020-8681, under solicitation SPE4A6-26-T-14VT, with a response deadline of August 18, 2026, and a delivery requirement of 20 days after order. This is a total small business set-aside under NAICS code 336413, managed by the Department of Defense’s ASC Commodities Division. The item is subject to stringent export control regulations under ITAR or EAR, meaning any handling, disclosure, or transmission of associated technical data to foreign persons—regardless of location—requires prior authorization from the Department of State or Commerce. DFARS 252.225-7048 governs the protection of this data, and distribution is restricted to DLA contractors who hold an approved US/Canada Joint Certification Program designation, have completed mandatory DOD export control training, and have been formally authorized by DLA. Additionally, the winning contractor must be a Cybersecurity Maturity Model Certification Level 2 certified third-party assessment organization and must ensure physical identification and bare item marking compliance to meet all contractual requirements.
ASC COMMODITIES DIVISION

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336413
New
DIBBS
COUNTER AND CHUTE A
Solicitation # SPE8EF-26-T-1610
The contract is for the procurement of two units of a Counter and Chute Assembly identified by NSN 1730-01-082-4002 under solicitation SPE8EF-26-T-1610, with a total delivery timeline of 52 days after order. The acquisition is a Total Small Business Set-Aside under FAR 19.5, restricted to small business entities, and classified under NAICS code 336413 for defense equipment manufacturing. The item involves technical data subject to export controls under either ITAR or EAR, requiring strict compliance with DFARS 252.225-7048; disclosure to foreign persons, including foreign nationals in the U.S. or abroad, is prohibited without prior authorization from the Department of State or Commerce. Access to this technical data is restricted to contractors with approved US/Canada Joint Certification Program credentials, completion of mandatory DOD export training, and formal approval from DLA. Packaging must meet DLA procurement standards, and non-accepted supplies must have all government identification removed. The contract requires CMMC Level 2 certification for any third-party assessment organization involved, and technical and quality requirements referenced are governed by the DLA Master List as of the solicitation or award date depending on acquisition size. Delivery is targeted to New Cumberland, Pennsylvania, with Shannon Anderson at DLA as the primary point of contact for inquiries.
CONSTRUCTION & EQUIPMENT MANU & CON

POSTED

about 18 hours ago

DEADLINE

in 10 days
View Details
NAICS: 336413
New
DIBBS
BRACKET ASSY, CYLIND
Solicitation # SPE4A7-26-T-637H
The contract solicitation SPE4A7-26-T-637H requires the procurement of six units of a BRACKET ASSY, CYLIND with NSN 1680-00-465-9457, to be delivered FOB ORIGIN within 102 days of contract award, with a required delivery date of November 4, 2027. The item is classified as a critical application item and must be manufactured by AVOX SYSTEMS INC under part number 800579-01. Sampling and inspection are governed by strict quality standards: MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based sampling plan must be used, with unspecified attributes deemed major. Inspection and acceptance occur at origin, and the manufacturer’s inspection system must comply minimally with SAE AS9003 or ISO 9001 tailored to AS9003 standards. Acceptance requires zero non-conformances in the sample lot, and verification levels for critical, major, and minor attributes are fixed at VII, IV, and II respectively, or AQLs of 0.1, 1.0, and 4.0. Packaging must adhere to ASTM D3951, but DLA Master List requirements take precedence, and all packaging and labeling must conform to MIL-STD-129. Palletization follows RP001: DLA Packaging Requirements for Procurement. The contractor is required to complete a CMMC Level 2 self-assessment, safeguard covered defense information under FAR 252.204-7012, and comply with NIST SP 800-171 DOD assessment requirements. The Berry Amendment and Buy American Act apply with a $150,000 threshold, and non-domestic material disclosures are mandatory. Safety Data Sheets meeting 29 CFR 1910.1200(g) and Federal Standard No. 313 must be submitted prior to award, and hexavalent chromium is prohibited. The contractor must register in DLA’s AMPS system to access the Vendor Shipment Module and comply with all DLA procurement directives. The contract includes provisions on whistleblower rights, disclosure of information, cybersecurity incident reporting, electronic invoicing via WAWF, and restrictions on mandatory arbitration and acquisition of prohibited telecommunications equipment. Quotes must be
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336413
New
DIBBS
CAP ASSEMBLY, FILLER, VE
Solicitation # SPE8EF-26-T-1611
The contract specifies the procurement of two units of a miniature vented cap assembly, identified by NSN 1730-01-131-4493 and part number 7M710-1 from The Boeing Company and FCS-M from Lenz Inc, with a total value of $2.00 per unit. Delivery is required within 20 days from the contract award, FOB origin, with no tolerance for quantity variance. Inspection and acceptance occur at the destination, and packaging must strictly comply with MIL-STD-2073-1E and DLA packaging requirements, including specified preservation methods, wrapping, and unit container standards. Marking must follow MIL-STD-129 with no special marking codes applied, and palletization must adhere to DLA guidelines. The final delivery destination is RAF Lakenheath, Building 1035, Suffolk, United Kingdom, with the same address used for freight shipping and marking. Transportation details reference DLAD Proc Notes C19 and C20. Technical and quality requirements are incorporated by reference from the DLA Master List, and the contract is subject to defense information handling protocols. The solicitation number is SPE8EF-26-T-1611, with a response deadline of August 21, 2026, and the original required delivery date is August 12, 2026. The contract falls under NAICS code 336413 and is authorized by the Department of Defense.
CONSTRUCTION & EQUIPMENT MANU & CON

POSTED

about 18 hours ago

DEADLINE

in 10 days
View Details
NAICS: 336413
New
DIBBS
GOVERNMENT FIRST ARTIC
Solicitation # SPE4A7-26-T-637M
The procurement is for four units of a PIN, DOOR VISOR with NSN 0001S00000052, manufactured under the NAICS code 336413 and sourced through a Small Business Set-Aside. The item may require casting or forging and typically involves specialized tooling not held by the government, necessitating coordination through the DLA Casting and Forging Assistance portal for sourcing support. Manufacturing must adhere to tailored high-level quality requirements, with the supplier’s inspection system required to meet a minimum standard of SAE AS9003 or ISO 9001 tailored to AS9003. Additive manufacturing is strictly prohibited unless explicitly authorized, and any offer incorporating AM is ineligible for award. First article testing is mandatory, requiring the submission of two units to Warner Robins ALCMC within 180 calendar days of contract award, with the government conducting tests and providing written approval or rejection within 240 days. Inspection and acceptance occur at origin per FAR 52.246-2, and sampling must follow MIL-STD-1916, ASQ H1331, or an equivalent zero-based plan with critical, major, and minor attributes held to AQLs of 0.1, 1.0, and 4.0 respectively. Packaging and marking are governed by MIL-STD-129 with special marking code 00 and palletization per DLA RP001, while no item unique identification is required per customer request. The item contains export-controlled technical data subject to ITAR or EAR regulations, restricting disclosure to foreign persons and requiring contractors to hold an approved US/Canada Joint Certification Program certification, complete mandatory DOD export control training and DLA questionnaire, and receive explicit approval from the DLA controlling authority. Cybersecurity requirements include compliance with DFARS 252.204-7012 for safeguarding covered defense information and adherence to CMMC Level 2 certification for all third-party assessment organizations. Payment must be processed electronically through WAWF, with required DoDAAC fields specified in the eventual award. All offers must be submitted via DIBBS by August 18, 2026, and include a Safety Data Sheet, or the offeror will be deemed nonresponsible. The contract is governed by multiple FAR and DFARS clauses addressing whistleblower rights, disclosure controls, prohibition of hexavalent chromium, Buy America requirements
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 336413
New
DIBBS
PLATE, SCUFF, HYDRAUL
Solicitation # SPE4A7-26-R-XA11
The contract solicitation SPE4A7-26-R-XA11 issued by the Department of Defense’s DLA Aviation, ASC Supplier Oper AE and AF Division, seeks the procurement of a single item—the PLATE, SCUFF, HYDRAULIC—with NSN 1650-00-321-6288 and part number 86158-1, sourced exclusively from HYDRO-AIRE AEROSPACE CORP or CRANE COMPANY. This is a critical application item under an indefinite delivery contract with a five-year base period, a guaranteed minimum purchase of 20 units, and a maximum contract value cap of $350,000. Pricing is firm fixed price with no variance allowance, and delivery must occur 156 days after receipt of order under FOB destination terms. Inspection and acceptance are conducted at origin, and the contractor must adhere to stringent quality standards including ISO 9001:2015, MIL-STD-1916 or ASQ H1331 Table 1 sampling for verification, and strict assignment of verification levels or AQLs based on attribute classification. Packaging must conform to ASTM D3951, but all DLA Master List of Technical and Quality Requirements prevail; palletization follows RP001, and all labeling complies with MIL-STD-129, including hazardous and radioactive material marking per applicable federal regulations. Compliance with cybersecurity and regulatory mandates is mandatory, including CMMC Level 2 self-assessment, NIST SP 800-171 DOD assessment requirements through DFARS 252.240-7997, and adherence to Buy America, domestic preference, and prohibited sourcing rules such as restrictions on materials from Xinjiang and unmanned aircraft systems from covered foreign entities. Contractors must satisfy multiple DFARS and FAR clauses covering counterfeit part avoidance, electronic part sourcing, safety notifications, trafficking in persons, paid sick leave, and DEI discrimination prohibitions. The contractor must maintain an active SAM registration with current representations and certifications, and submit proposals via DIBBS or email to Michael Kershaw, while ensuring submissions do not exceed 15 MB. Invoicing must be processed through WAWF using prescribed DoDAACs, and all documentation, configuration changes, and deviations require formal engineering change proposal processing. The acquisition is not a small business set-aside and will be awarded based on a best
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 18 hours ago

DEADLINE

in 13 days
View Details
NAICS: 336413
New
DIBBS
COVER, SEAT CUSHION,
Solicitation # SPE7LX-26-U-9530
The contract pertains to the procurement of a cover for a seat cushion, identified by part number 109826-1 and NSN 1680-01-617-6695, supplied by BAE Systems Land & Armaments L.P. with CAGE code 54786. The requirement is issued under solicitation SPE7LX-26-U-9530 with a delivery window of 165 days, FOB origin, and a fixed quantity of 42 units at a unit price of $42.00, totaling $1,764. The contract prohibits any quantity variance and mandates inspection and acceptance at the destination. Technical and quality requirements referenced via R and I numbers are governed by the DLA Master List of Technical and Quality Requirements, which supersede all other standards including ASTM D3951. Packaging must comply with MIL-STD-129 and RP001 DLA Packaging Requirements, and palletization must adhere to specified DLA standards. All packaging and labeling must be marked appropriately, and the Unit of Issue and Quantity per Unit Pack must match the contract specifications. Sampling for quality assurance must follow MIL-STD-1916 or ASQ H1331 Table 1, or an equivalent zero-based sampling plan, with critical, major, and minor attributes assigned verification levels VII, IV, and II respectively, or AQLs of 0.1, 1.0, and 4.0. Unspecified attributes are treated as major. MIL-STD-105/ASQ Z1.4 may be used to determine sample size, but acceptance requires zero non-conformances unless otherwise stipulated in the contract. The manufacturer may choose attribute or variable inspection under MIL-STD-1916 unless restricted by contract terms. Configuration changes require an Engineering Change Proposal or variance request, and documentation for source approval is mandatory. The item is classified as a critical application item, and all government identification must be removed from non-accepted supplies. The contract was posted on August 10, 2026, with responses due by August 25, 2026, and is managed under the Department of Defense’s Strategic Acquisition Program Directorate.
STRATEGIC ACQ PROGRAM DIRECTORATE

POSTED

about 18 hours ago

DEADLINE

in 14 days
View Details
NAICS: 336413
New
DIBBS
SKIN, AIRCRAFT
Solicitation # SPE4A7-26-R-0688
The contract pertains to the procurement of an aircraft skin part designated by NSN 1560-011519541 and part number 65-55125-1, manufactured in accordance with drawing 81205 65-55125 Revision C dated November 4, 1988. This is an indefinite quantity contract with a five-year base period and no option periods, under a total small business set-aside, with an estimated annual requirement of 40 units. Deliveries are required to be completed within 300 days after order placement, with FOB origin terms and inspection and acceptance also conducted at the origin. Access to technical data associated with this item is restricted to contractors certified by the Department of Defense under DOD 5220.22M, requiring submission of DD Form 2345 to the Defense Logistics Information Services. The solicitation, numbered SPE4A726R0688, will be issued on or about August 10, 2026, and is only available electronically via the DLA Internet Bid Board System; no paper copies will be provided. Proposals must be submitted by September 10, 2026, and all correspondence should be directed to Ryan Loeffelholz at the Department of Defense, Defense Logistics Agency Aviation, located in Richmond, Virginia.
ASC SUPPLIER OPER AE AND AF DIV

POSTED

about 18 hours ago

DEADLINE

in about 1 month
View Details

More opportunities from Department Of Defense → ASC SUPPLIER OPER AE AND AF DIV

Same awarding agency

NAICS: 332999
New
DIBBS
Precision Hydraulic Scuff Plate ManufacturingThe contract requires the manufacture of a military-specification hydraulic scuff plate identified by NSN 1650-00-321-6288, to be produced in full compliance with DLA Master List standards and rigorous precision metal fabrication protocols. All components must adhere to strict dimensional tolerances and material specifications, with end-to-end traceable quality controls implemented at every stage of production to ensure operational reliability and regulatory compliance. The manufacturing process must include documented inspections, material certifications, and lot tracking to maintain accountability throughout the supply chain. This is a subcontract opportunity under NAICS code 332999, issued by the Department of Defense through the ASC SUPPLIER OPER AE AND AF DIV, with a response deadline of August 24, 2026. The work must be performed to meet DoD-specific performance requirements without deviation, and all deliverables are expected to support military systems requiring durable, high-stress components. While no set-aside designation or point of contact details are provided, bidders are directed to the DIBBS portal for complete solicitation documentation and must ensure full alignment with military-grade manufacturing and certification expectations.
All Other Miscellaneous Fabricated Metal Product Manufacturing

POSTED

about 18 hours ago

DEADLINE

in 13 days
View Details
NAICS: 541512
New
DIBBS
Cybersecurity Compliance and CMMC Assessment Support
Computer Systems Design Services

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 493190
New
DIBBS
Packaging, Labeling, and Hazard Communication Compliance
Other Warehousing and Storage

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332721
New
DIBBS
Precision Machined Component Manufacturing – SPACER, RING
Precision Turned Product Manufacturing

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 488510
New
DIBBS
Transportation and Ocean Shipping Compliance
Freight Transportation Arrangement

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 541380
New
DIBBS
Hazardous Materials Compliance and Packaging Services
Testing Laboratories and Services

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 332313
New
DIBBS
Supply of Heavy Hex Machine Bolts for Defense Contract
Plate Work Manufacturing

POSTED

about 18 hours ago

DEADLINE

in 7 days
View Details
NAICS: 541512
New
DIBBS
Cybersecurity Compliance and CMMC Level 2 Implementation
Computer Systems Design Services

POSTED

about 18 hours ago

DEADLINE

in 9 days
View Details
NAICS: 541380
New
DIBBS
First Article Testing (FAT) Support and Documentation
Testing Laboratories and Services

POSTED

about 18 hours ago

DEADLINE

in 9 days
View Details
NAICS: 332812
New
DIBBS
Surface Finishing and Aircraft Coating Application
Metal Coating, Engraving (except Jewelry and Silverware), and Allied Services to Manufacturers

POSTED

about 18 hours ago

DEADLINE

in 9 days
View Details
NAICS: 332999
New
DIBBS
Mechanical Fastener Installation and Sealing
All Other Miscellaneous Fabricated Metal Product Manufacturing

POSTED

about 18 hours ago

DEADLINE

in 9 days
View Details
NAICS: 332813
New
DIBBS
Heat Treatment of Aluminum Alloy Components
Electroplating, Plating, Polishing, Anodizing, and Coloring

POSTED

about 18 hours ago

DEADLINE

in 9 days
View Details