Coordinate Measuring Machine

REQUEST FOR INFORMATION- REQUEST INDUSTRY PROVIDE INFORMATION AND A BUDGETARY COST ESTIMATE FOR TURN-KEY SUPPLY, INSTALLATION AND TRAINING FOR A COORDINATE MEASURING MACHINE (CMM) AT TOBYHANNA ARMY DEPOT, TOBYHANNA PA 18466 BACKGROUND AND BASIC REQUIREMENTS This Request for Information (RFI) is being conducted to identify potential sources that may possess the expertise, capabilities, and experience to meet the requirements for providing the turn-key installation of a Coordinate Measuring Machine (CMM) to include all necessary engineering and design; to include the site preparation work, such as excavation work, concrete and isolation pad installation; to include the supply, delivery, installation, documentation and personnel training for a CMM. This RFI is issued solely for market research information and planning purposes only and does not constitute a solicitation. Responses will be treated as information only and will not be used as a proposal. The information submitted in response to this RFI may be used to help the Government further define its requirements. In accordance with FAR 15.201(e), responses to this notice are not offers and cannot be accepted by the Government to form a binding contract. The Government does not intend to make an award on the basis of this RFI. Companies responding to this RFI are advised that a response does not ensure participation in a future solicitation or contract award. The Government will not reimburse participants for any expenses associated with participation in this RFI. All information received in response to this RFI that is marked proprietary will be handled accordingly. Responses to this RFI that indicate that the information therein is proprietary, or represents confidential business information, will be received and held in confidence. Proprietary information submitted as part of responses to the RFI should be clearly identified and it will be treated as such. The Government reserves the right to follow up on a one-on-one basis with RFI respondents to gain additional information or clarity about information submitted. GENERAL REQUIREMENTS The Government is seeking to identify contractors capable of satisfying this requirement at the prime contractor level with full responsibility for contractor and sub-contractor personnel, equipment, and services. The Government requests that submitting contractors identify a representative to support further Government inquiries and requests for clarifications of the information provided. Respondents should indicate which portions of their response are proprietary and should mark them accordingly. Responses to this RFI should include the name, telephone number, and email address of a Point of Contact (POC) having authority and knowledge to discuss responses. Questions regarding this RFI can be e-mailed to: Mr. Shane Alt Shane.d.alt.civ@mail.mil Complete written responses to this RFI are to be submitted to the above referenced e-mail address. Respondents should include the following business information with the RFI response: 1) Company name; 2) Company address; 3) Point of Contact; 4) Telephone Number; 5) E-mail address; 6) Company Cage Code; 7) Primary NAICS; 8) Business Size; 9) Current Registration in SAM; 10) Web page address. General CMM Information - CMM to be delivered to Tobyhanna Army Depot in Tobyhanna, PA, and installed within a building at Tobyhanna Army Depot. - CMM to be of bridge-type design with measuring ranges: 47" x-axis, minimum; 78" y-axis, minimum; and 39" z-axis, minimum. Describe table composition, dimensions, and weight capacity as part of general information. - Identify the measuring accuracy in all 3 dimensions and describe the measuring ability of the machine; that is, the machine's ability to measure complex curvatures on parts, for example, fan blade surfaces and gear profiles. - Identify whether the CMM is equipped with an articulating probe and describe its articulation increments and range of rotation per axis. Identify the fixed probe head accuracy. - Describe software used by the CMM for operation. Identify whether software is inclusive of Product Manufacturing Information (PMI). - Describe machine vibration isolation system along with temperature and humidity requirements. Please identify whether temperature and vibration compensation are part of the machine software. - Identify utility requirements. - Identify types of probing (stylus, laser, integrated stylus & laser, etc.) available for the machine. Identify advantages and deficiencies of each type. - Identify training that is offered; training location; and duration of training for operator personnel and for maintenance personnel. - Identify calibration requirements. - The below are updated requirements for all Information Technology (IT) equipment that are to be connected to a Government computer network. Definitions This section contains explanations of terms used in this document. They are taken from, and not to supersede, those definitions given in Army Regulation (AR) 25-1. All terms used in this document are in accordance with AR 25-1. Hardware Requirements Without exception, all Information Technology (IT) equipment shall comply with any and all applicable Security Technical Implementation Guides (STIGs) and Security Requirement Guides (SRGs) as published by the Defense Information Systems Agency (DISA). This includes STIGs and SRGs regarding physical security. STIGs can be publically viewed on the DISA website. In addition, all IT equipment will comply with relevant Department of Defense (DOD) guidance and mandates regarding hardware lifecycle upgrades. Only standardized, Government owned, managed, and maintained computing hardware shall be utilized as workstations or servers. Upon solicitation, plans to meet these requirements must be laid out by the vendor and deemed acceptable by TYAD. Also upon solicitation, vendor must submit detailed part information of all IT equipment and IT components to be delivered to TYAD. Prior to final award the vendor must be able to provide documentation as proof that these requirements have been met. Software Requirements Without exception, all IT equipment shall comply with any, and all, applicable STIGs and SRGs developed by DISA, as well as relevant Army guidance, and mandates. All are publically available on the DISA website. Any, and all software intended to be used on, with, or in support of an IT equipment is required to have a current and valid Authority to Operate (ATO), and approval from TYAD Configuration Control Board (CCB). ATO, and CCB approval are to be provided by TYAD but are contingent on the vendor meeting the requirements in the SOW. Upon solicitation, plans to meet these requirements must be laid out by the vendor and deemed acceptable by TYAD. Also upon solicitation, vendor must submit detailed software information of all software and software packages existing on IT equipment and components to be delivered to TYAD. Prior to final award the vendor must be able to provide documentation as proof that these requirements have been met. Support Requirements All IT equipment are required to have a valid support contract for at least the software and firmware. While a support contract is in effect the following requirements and all those listed in applicable DISA STIGs and SRGs, as well as relevant DOD guidance, and mandates shall apply. Testing Requirements The vendor and any and all of their sub-contractors, shall provide additional hardware and licenses to simulate all system functionality in a laboratory environment. These assets are to be used for testing purposes only and will not be deployed for production use. In order to ensure that security updates and configurations do not interfere with IT equipment in production use, the government requires the ability to test a representative system in a controlled laboratory environment. Services and Equipment Information The Government is interested in obtaining information from companies that can provide turn-key design, supply, delivery, site preparation, installation, documentation and training. As a turn-key installation the company will be responsible to supply all personnel and equipment to engineer and design the CMM; perform foundation and isolation platform excavation and installation; supply, deliver, assemble and install the new CMM; perform calibration for the CMM; supply all appropriate documentation for the CMM; and to train Government personnel in the operation and maintenance of the new CMM. A Budgetary Cost Estimate by respondents is requested with response to this RFI. The Budgetary Cost Estimate should include the costs associated with General CMM Information and Services and Equipment Information. As a part of the Budgetary Cost Estimate respondents should take into account any and all costs associated with making the CMM compliant with the IT requirements listed above.