HYDROSTATIC HOSE TEST STAND

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6 and FAR 13, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. Instructions to offerors, evaluation criteria, and all applicable FAR Provisions and Clauses are attached. The solicitation number is 70Z035-20-Q-6WNMAA00 and is issued as a Request for Quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2019-05. This acquisition is set-aside 100% for SMALL BUSINESS. Where Federal Acquisition Regulation clause language is inconsistent with FAR 13.004, Legal Effect of Quotations, that language is hereby tailored in accordance with FAR 12.302 to be consistent with a request for quotations. This tailoring includes, but is not limited to the following: In accordance with FAR 13.004, a quotation is not an offer, and any clause provision to the contrary is hereby modified to be consistent with FAR 13.004. Where the word "offer/offeror" or a derivative of that word appears, it is changed to "quote/quoter" or a derivative of that word. The associated NAICS code is 334519 and the small business size standard is 500 employees. Requirements for Hydrostatic Hose Test Stand Integral test chamber measurements nominally 72" x 24" x 12" high. Chamber to be manufactured in 12 gauge brushed stainless steel with reinforced corners, stainless latches with secondary safety catch, shielded rear venting and a �" clear polycarbonate door for visibility during testing. Gas springs for the door, NPT drain connection with stainless plug and stainless steel -4 male 37� JIC bulkhead pressure port fittings. All connections must be inside enclosure and controls outside enclosure for operator safety. Price must include Shipping to freight forwarder in Tukwilla WA, Zip Code 98167 other requiremits listed below For use with water Loop style manifold with 7/16-20 straight thread boss (MS33649-04) high pressure outlet and return ports 1 each, � NPT accessory port 1 set 37� flared test adapter fittings for MS28741 hose ends, -3,-4,-5,-6,-8,-10,-12,-16. 2 each/set 1 set flare-less test adapter fittings for MS28762 hose ends, -3,-4,-5,-6,-8,-10,-12,-16. 2 each/set 1 set pipe test adapter fittings for male NPT hose ends, 1/8, �, 3/8, �, �, and 1" NPT. Two each Integral stainless shelves and foam retaining inserts for test fittings 10 (Minimum) Gallon Stainless Reservoir mounted under the test chamber to accommodate fluid recycle Hose air Flush to assist in evacuating test fluid from hose after test Maximum Fluid Pressure 10,000 psi Inlet power supply (air) 0-90 psi Factory set air pressure relief valve to prevent over-pressurization of tester Output shutoff valve to isolate unit under test and high pressure gauge from test system ASME B40.1 grade 1A hydraulic pressure gauge 1% full scale accuracy Bleed Valve to release pressure prior to disconnecting unit under test All stainless steel wetted components for Strength, durability, corrosion resistance Precision regulator to allows precise control over a broad range hydrostatic pressures All quotes are due at USCG Base Ketchikan, AK by the 1159 (Alaska Time) 28 October 2019. Submit quotes to the following mailing address, e-mail address, or fax number by the offer due date and time: U.S. Coast Guard Base Ketchikan 1300 Stedman Street Ketchikan, Alaska 99901-6661 United States Attn: SK1 Jamie Bridges E-Mail Address: Jamie.C.Bridges@uscg.mil Fax Number: (907) 228-0297 (Attn: SK1 Jamie Bridges) Any and all questions regarding this solicitation shall be submitted in writing to the Contract Specialist at Jamie.C.Bridges@uscg.mil