Laser Relay imaging lenses

SLAC National Accelerator Laboratory is operated by Stanford University for the Department of Energy. As a management and operating contractor, subcontracts awarded by the Laboratory are not Federal procurements, and are not directly subject to the Federal Acquisition Regulations in 48 CFR. Nonetheless, certain Federal laws, Executive Orders, and regulations may affect our DOE approved purchasing system, as required by statute, regulation, or contract terms and conditions. HI, HI, The following Addendum 2 is being issued for the subject Request for Quotation: 343783 Answers to questions. Please see below answers to questions: What radius tolerances do you need? +/- 1 % should be fine. What Irregularity tolerances do you need? - wave at 632.8 nm What is the center thickness of this lens? 3.3 mm +/- 0.1 mm What are the Clear Apertures? 80-90% Is there a sag/sag tolerance? No Is this coated? No What surface quality do you need? 40-20 Is the power 2 on both sides? No, this is plano convex preferably. Is test plate fit ok? Yes ETD spec for these lenses, and will they need coating? - we do not have damage threshold specifications and the optics are to be uncoated. This Addendum modifies the Request for Quotation and must be acknowledged. Failure to acknowledge all addenda could make your proposal non-responsive. Please confirm that the submitted proposal is not changed because of this addendum. If proposal sent is revised because of this, please submit the revised proposal. The following changes are hereby made to the appropriate documents contained the above-mentioned Request for Quotation (RFQ). All other terms and conditions of the RFQ remain the same. Thank you very much. The following Addendum is being issued for the subject Request for Quotation: 343783 Answers to questions: Center thickness Something around 3.3 mm preferred. Surface quality 40-20 Scratch-Dig Irregularity Lambda/2 on flat side. Power 3 Lambda/2 if possible This Addendum modifies the Request for Quotation and must be acknowledged. Failure to acknowledge all addenda could make your proposal non-responsive. Please confirm that the submitted proposal is not changed because of this addendum. If proposal sent is revised because of this, please submit the revised proposal. The following changes are hereby made to the appropriate documents contained the above-mentioned Request for Quotation (RFQ). All other terms and conditions of the RFQ remain the same. Required item(s) listed below: 1.) 38.1 mm diameter UVFS plano convex lens, 792.23 mm ROC = Qty 5 2.) 38.1 mm diameter UVFS plano convex lens, 1485.65 mm ROC. = Qty 10 3.) 38.1 mm diameter UVFS plano convex lens, 2900.61 mm ROC. = Qty 9 4.) 38.1 mm diameter UVFS plano convex lens, 3397.35 mm ROC. = Qty 5 5.) 38.1 mm diameter UVFS plano convex lens, 4370 mm ROC. = Qty 5 6.) 38.1 mm diameter UVFS plano convex lens, 2167.91 mm ROC. = Qty 5 7.) 38.1 mm diameter UVFS plano convex lens, 3888.00 mm ROC. = Qty 5 8.) 38.1 mm UVFS plano convex lens, 1011.58 mm ROC. = Qty 14 Technical evaluation criteria are as follows: Lenses manufactured out of Corning 7980 grade 0-F glass or from equal or better equivalent Lenses will be 1.5 inches (38.1 mm) in diameter with standard industry tolerances on the diameter The radius of curvature tolerance will be measured to be less than +/- 0.5% of the focal lengths up to 4 meters and +/- 1% of the focal length beyond 4 meters The lens radius of curvature values shall be within 1 percent or better from those specified in the requirements The lead time shall be 10 weeks or less ARO Quote is for product only; no on-site services permitted. Source selection will be based on Lowest Priced Tecnically Acceptable Method. Please provide a price and lead time quotation by COB Feb. 26, 2024. Send quote to contact@example.gov. Is there any room for additional discount such as for Academic, ICPT, GSA, or Government Institutions? Buy American Act Certification (BAA) applies to award over $10,000. Representations & Certifications Rider is required. Once completed the Reps and Certs is valid for one year until renewal. If you have already completed one within the year please disregard. Otherwise, please complete and return. All subcontractors are required to register in the System for Award Management (www.sam.gov). If possible, please provide a link to your webpage for published price list to substantiate for the prices quoted. The resulting purchase order will be issued on a fixed price basis. SLAC National Accelerator Laboratory Terms and Conditions for Fixed Price Commercial Supplies and Services (Rev. March 2023) will be made a part of the resulting order. Payment Terms will be NET-30 Freight terms will be FOB Destination Prepaid and Add You are requested to mark and identify proprietary/confidential information provided in response to the solicitation. Contact me directly with any questions. Sincerely, Katherine Jill A. Coh Procurement Commodities Team Lead SLAC National Accelerator Laboratory 2575 Sand Hill Road Menlo Park, CA 94025 Phone: +1 (555) 000-0000 Email: contact@example.gov