This Solicitation opportunity from Department Of Defense was posted on July 27, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
LEFT BASE ASSY
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The LEFT BASE ASSY with NSN 4925-01-568-6999 is solicited under contract SPE4A7-26-Q-0879 for a quantity of two units, with delivery required within 198 days after award. This procurement is governed by DLA packaging and technical requirements referenced in the DLA Master List of Technical and Quality Requirements, with applicable revisions determined by the solicitation or award date depending on acquisition size. The item is not required to be uniquely identified under DFARS 252.211-7003(c)(1)(i), but must comply with specific dimensional corrections listed on drawings 3305AS1702 and 3305AS1705, including a radius of 0.25 inches and a missing dimension of 0.190 inches in specified zones. Sampling and inspection must follow MIL-STD-1916 or ASQ H1331 Table 1, with zero non-conformances required unless otherwise stated, and attribute classifications must align with verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 for critical, major, and minor characteristics respectively. Technical data associated with this item is subject to export control under either ITAR or EAR, prohibiting any disclosure or transfer to foreign persons without prior authorization from the Department of State or Commerce. DFARS 252.225-7048 applies, restricting access to contractors holding valid US/Canada Joint Certification Program certification, having completed DLA-mandated export control training and questionnaire, and been formally approved by DLA. Government identification must be removed from non-accepted supplies, and all quality assurance protocols must strictly adhere to the referenced military standards. The solicitation was posted on July 27, 2026, with responses due by August 6, 2026, and is managed by the Department of Defense’s ASC Supplier Oper AE and AF Division, with Mykhara Robinson as the primary point of contact.
General Info
Agency
NAICS
Place of Performance
USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
RD002, COVERED DEFENSE INFORMATION APPLIES
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. REI # R-MA-12-85773 2 NOV 2012 ON DRAWING 3305AS1702: THE RADIUS SHOULD BE: 0.25 INCHES ON DRAWING 3305AS1705: THE MISSING DIMENSION IN ZONES C-1 AND C-3 IS: 0.190 INCHES IDENTIFY TO:
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 4925-01-568-6999 Quantity: 2 EA Purchase Request: 7017487777QTY: 2 Delivery: 198 days ADO
More opportunities from Department Of Defense → ASC SUPPLIER OPER AE AND AF DIV
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS