PARTS KIT, GUN

(ii) Items for which the Government's unit acquisition cost is less than $5,000 that are identified in the Schedule or the following table: Contract Line, Subline, or Exhibit Line Item Number Item Description
(iii) Subassemblies, components, and parts embedded within delivered items, items with warranty requirements, DoD serially managed reparables and DoD serially managed nonreparables as specified in Attachment Number. (iv) Any item of special tooling or special test equipment as defined in FAR 2.101 that have been designated for preservation and storage for a Major Defense Acquisition Program as specified in Attachment Number. (v) Any item not included in paragraphs (c)(1)(i), (ii), (iii), or (iv) of this clause for which the contractor creates and marks a unique item identifier for traceability. (2) The unique item identifier assignment and its component data element combination shall not be duplicated on any other item marked or registered in the DoD Item Unique Identification Registry by the contractor. (3) The unique item identifier component data elements shall be marked on an item using two dimensional data matrix symbology that complies with ISO/ IEC International Standard 16022, Information technology International symbology specification Data matrix; ECC200 data matrix specification. (4) Data syntax and semantics of unique item identifiers. The Contractor shall ensure that (i) The data elements (except issuing agency code) of the unique item identifier are encoded within the data matrix symbol that is marked on the item using one of the following three types of data qualifiers, as determined by the Contractor: (A) Application Identifiers (AIs) (Format Indicator 05 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (B) Data Identifiers (DIs) (Format Indicator 06 of ISO/IEC International Standard 15434), in accordance with ISO/IEC International Standard 15418, Information Technology EAN/UCC Application Identifiers and Fact Data Identifiers and Maintenance and ANSI MH 10.8.2 Data Identifier and Application Identifier Standard. (C) Text Element Identifiers (TEIs) (Format Indicator 12 of ISO/IEC International Standard 15434), in accordance with the Air Transport Association Common Support Data Dictionary; and (ii) The encoded data elements of the unique item identifier conform to the transfer structure, syntax, and coding of messages and data formats specified for Format Indicators 05, 06, and 12 in ISO/IEC International Standard 15434, Information Technology-Transfer Syntax for High Capacity Automatic Data Capture Media. (5) Unique item identifier. (i) The Contractor shall (A) Determine whether to ( 1 ) Serialize within the enterprise identifier; ( 2 ) Serialize within the part, lot, or batch number; or ( 3 ) Use a DoD recognized unique identification equivalent (e.g. Vehicle Identification Number); and (B) Place the data elements of the unique item identifier (enterprise identifier; serial number; DoD recognized unique identification equivalent; and for serialization within the part, lot, or batch number only: Original part, lot, or batch number) on items requiring marking by paragraph (c)(1) of this clause, based on the criteria provided in MIL-STD-130, Identification Marking of U.S. Military Property, latest version; (C) Label shipments, storage containers and packages that contain uniquely identified items in accordance with the requirements of MIL-STD-129, Military Marking for Shipment and Storage, latest version; and (D) Verify that the marks on items and labels on shipments, storage containers, and packages are machine readable and conform to the applicable standards. The contractor shall use an automatic identification technology device for this verification that has been programmed to the requirements of Appendix A, MIL-STD-130, latest version.
SPE7LX-26-R-X047
Part 12 Clauses (CONTINUED)
(ii) The issuing agency code (A) Shall not be placed on the item; and (B) Shall be derived from the data qualifier for the enterprise identifier. (d) For each item that requires item unique identification under paragraph (c)(1)(i), (ii), or (iv) of this clause or when item unique identification is provided under paragraph (c)(1)(v), in addition to the information provided as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the Contractor shall report at the time of delivery, as part of the Material Inspection and Receiving Report, the following information: (1) Unique item identifier. (2) Unique item identifier type. (3) Issuing agency code (if concatenated unique item identifier is used). (4) Enterprise identifier (if concatenated unique item identifier is used). (5) Original part number (if there is serialization within the original part number). (6) Lot or batch number (if there is serialization within the lot or batch number). (7) Current part number (optional and only if not the same as the original part number). (8) Current part number effective date (optional and only if current part number is used). (9) Serial number (if concatenated unique item identifier is used). (10) Government's unit acquisition cost. (11) Unit of measure. (12) Type designation of the item as specified in the contract schedule, if any. (13) Whether the item is an item of Special Tooling or Special Test Equipment. (14) Whether the item is covered by a warranty. (e) For embedded subassemblies, components, and parts that require DoD item unique identification under paragraph (c)(1)(iii) of this clause or when item unique identification is provided under paragraph (c)(1)(v), the Contractor shall report as part of the Material Inspection and Receiving Report specified elsewhere in this contract, the following information: (1) Unique item identifier of the parent item under paragraph (c)(1) of this clause that contains the embedded subassembly, component, or part. (2) Unique item identifier of the embedded subassembly, component, or part. (3) Unique item identifier type. (4) Issuing agency code (if concatenated unique item identifier is used). (5) Enterprise identifier (if concatenated unique item identifier is used). (6) Original part number (if there is serialization within the original part number). (7) Lot or batch number (if there is serialization within the lot or batch number). (8) Current part number (optional and only if not the same as the original part number). (9) Current part number effective date (optional and only if current part number is used). (10) Serial number (if concatenated unique item identifier is used). (11) Description. Once per item. (f) The Contractor shall submit the information required by paragraphs (d) and (e) of this clause as follows: (1) End items shall be reported using the receiving report capability in Wide Area WorkFlow (WAWF) in accordance with the clause at 252.232-7003. If WAWF is not required by this contract, and the contractor is not using WAWF, follow the procedures at http://dodprocurementtoolbox.com/site/uidregistry/. (2) Embedded items shall be reported by one of the following methods (i) Use of the embedded items capability in WAWF; (ii) Direct data submission to the IUID Registry following the procedures and formats at http://dodprocurementtoolbox.com/site/uidregistry/ ; or rmats at http://dodprocurementtoolbox.com/site/uidregistry/; or (iii) Via WAWF as a deliverable attachment for exhibit line item number (fill in) , Unique Item Identifier Report for Embedded Items, Contract Data Requirements List, DD Form 1423. (g) Subcontracts. If the Contractor acquires by subcontract any item(s) for which item unique identification is required in accordance with paragraph (c)(1) of this clause, the Contractor shall include this clause, including this paragraph (g), in the applicable subcontract(s), including subcontracts for commercial products or commercial services. (End of clause)
C04 UNUSED FORMER GOVERNMENT SURPLUS PROPERTY (SEP 2021)
To be considered for award, the offeror must complete and submit the following representation with their offer. Additional supporting documentation to demonstrate the surplus material offered was previously owned by the Government and meets solicitation requirements must be provided within 24 hours of request by the contracting officer. (1) The material is new, unused, and not of such age or so deteriorated as to impair its usefulness or safety. Yes [ ] No [ ] The material conforms to the technical requirements cited in the solicitation (e.g., Commercial and Government Entity (CAGE) Code and part number, specification, etc.). Yes [ ] No [ ] The material conforms to the revision letter/number, if any is cited. Yes [ ] No [ ] Unknown [ ] If No, the revision does not affect form, fit, function, or interface. Yes[ ] No [ ] Unknown [ ] The material was manufactured by: (Name): (Address): (2) The offeror currently possesses the material: Yes [ ] No [ ] If yes, the offeror purchased the material from a Government selling agency or other source. Yes [ ] No [ ] If yes, complete the following:
SPE7LX-26-R-X047
Part 12 Clauses (CONTINUED)
Government Selling Agency: Contract Number: Contract Date: (Month, Year): Other Source: Address: Date Acquired: (Month/Year): (3) The material has been altered or modified. Yes [ ] No [ ] If Yes, complete the following: Name of the company that performed the alternation or modification Address: Complete description of the alternations or modifications: (4) The material has been reconditioned. Yes [ ] No [ ] If Yes, complete the following: (i) The price offered includes the cost of reconditioning/refurbishment. Yes [ ] No [ ] (ii) Name of the company that reconditioned that material (iii) Description of any work done or to be done, including the components to be replaced and the applicable rebuild standard. The material contains cure-dated components. Yes [ ] No [ ] If Yes, complete the following: (i)The price includes replacement of cure-dated components. Yes [ ] No [ ] (ii) Cure date: (5) The material has data plates attached. Yes [ ] No [ ] If Yes, insert all information contained on the data plate: (6)The offered material is in its original package. Yes [ ] No [ ] If Yes, complete the following: Contract Number: NSN: CAGE Code: Part Number: Other Markings/Data: (7)The offeror has supplied this same material (National Stock Number) to the Government before. Yes [ ] No [ ] If Yes, complete the following: (i) The material being offered is from the same original Government contract number as that provided previously. Yes [ ] No [ ] (ii) State below the Government Agency and contract number under which the material was previously provided: Agency: Contract Number: (8)The material is manufactured in accordance with a specification or drawing. Yes [ ] No [ ] If Yes, complete the following: (i) The specification/drawing is in the possession of the offeror. Yes [ ] No [ ] (ii) The offeror has stated the applicable information below: Yes [ ] No [ ] Specification/Drawing Number: Revision: (if any): Date: (9) The material has been inspected for correct part number and for absence of corrosion or any obvious defects. Yes [ ] No [ ] If Yes, complete the following: (i) Material has been re-preserved. Yes [ ] No [ ] (ii) Material has been repackaged. Yes [ ] No [ ] (iii) Percentage of material that has been inspected is % ; and/or (iv) Number of items inspected is (v) A written report was prepared. Yes [ ] No [ ] The offeror agrees that in the event of award and notwithstanding the provisions of the solicitation. (i) Inspection and acceptance of the surplus material will be performed at source or destination subject to all applicable provisions for source or destination inspection. The offeror will forward to the contracting officer one of the following, within 24 hours of request by the contracting officer to demonstrate that the material being offered was previously owned by the Government (offeror check which one applies): [ ] For national or local sales, conducted by sealed bid, spot bid or auction methods, a solicitation/Invitation For Bid and corresponding DLA Disposition Services Form 1427, Notice of Award, Statement and Release Document. [ ] For DLA Disposition Services Commercial Venture (CV) Sales, the shipment receipt/delivery pass document and invoices/receipts used by the original purchaser to resell the material. [ ] When the above documents are not available, or if they do not identify the specific NSN being acquired, a copy or facsimile of all original package markings and data, including NSN, commercial and Government entity (CAGE) code and part number, and original contract number. (This information has already been provided in paragraph (6) of this procurement note. Yes [ ] No [ ] .) [ ] When none of the above are available, other information to demonstrate that the offered material was previously owned by the Government. Describe: This procurement note only applies to offers of Government surplus material. Offers of commercial surplus, manufacturer's overruns, residual inventory
SPE7LX-26-R-X047
Part 12 Clauses (CONTINUED)
resulting from terminated Government contracts, and any other material that meets the technical requirements in the solicitation but was not previously owned by the Government will be evaluated in accordance with the DLAD procurement note L04, Offers for Part Numbered Items. If requested by the contracting officer, the offeror shall furnish sample units, in the number specified, to the contracting officer or to another location specified by the contracting officer, within 10 days after the contracting officer's request. The samples will be furnished at no cost to the Government. All such samples not destroyed in NSN/Part Number: 1005-01-383-0168