Psst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveCLEATUS Webinar: AI for Government Contracting — Free Webinar — Wednesday, August 19 at 2:00 PM EDT

Register Free →

Search

Top

Back to Contracts

Plumbing and Piping Systems Installation

Active

Federal

Response Deadline08/12/2026, 07:00:00 PM UTC

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

Show more

The contract seeks the installation of potable water, sanitary sewer, and storm drainage systems for new or renovated facilities under the title Plumbing and Piping Systems Installation. It is classified as a subcontract and falls under the NAICS code 238220, which corresponds to Plumbing, Heating, and Air-Conditioning Contractors. The solicitation was posted on August 6, 2026, with a response deadline of August 12, 2026, at 7:00 PM. The work is being procured by the DLA Land and Maritime agency under the Department of Defense, though specific location details for performance are not provided. There is no set-aside designation indicated, meaning the contract is open to all eligible subcontractors without preference. While the point of contact and exact place of performance are unspecified, interested parties must submit proposals before the deadline to be considered for award.

General Info

Install potable water, sewer, and storm drainage systems as subcontract under DLA Land and Maritime by August 12, 2026.

Agency

Department Of Defense → DLA Land And MaritimeView Agency

NAICS

238220 - Plumbing, Heating, and Air-Conditioning ContractorsView NAICS

Place of Performance

OH

Set-Aside

NONE

Documents

(0)

No documents available

AI Contract Breakdown

Uniform Contract Format

No contract breakdown available.

Cannot generate Contract Breakdown because no documents were found from this contract's source.

Timeline

PostedAug 6

subcontract

Response DeadlineAug 12

Submission deadline

Response Deadline

08/12/2026, 07:00:00 PM UTCin 5 days

Ready to pursue this opportunity?

Start your free trial to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

Show more

AgencyDepartment Of Defense → DLA Land And Maritime

ContactsNo contacts available

OfficeN/A

Organization / Agency

Department Of Defense → DLA Land And Maritime

View Agency Profile

Office AddressN/A

ContactsNo contact information available

Full Description

Show more

Installation of potable water, sanitary sewer, and storm drainage systems in new or renovated facilities.

Similar Contracts

Same NAICS industry code

Catwalk and Handrail System Fabrication and Installation

POSTED

about 13 hours ago

DEADLINE

in about 1 month

Testing, Commissioning, and Calibration

Northlands Job Corps Center /ETR

POSTED

about 14 hours ago

DEADLINE

Mechanical Installation and Piping

Northlands Job Corps Center /ETR

POSTED

about 14 hours ago

DEADLINE

Propane Gas Tank Supply and Installation

Northlands Job Corps Center /ETR

POSTED

about 14 hours ago

DEADLINE

ESJC – FIRE EXTINGUISHER SERVICES

Solicitation # esjc-fire-extinguisher-services

This is a subcontracting opportunity for fire extinguisher inspection and servicing at the Excelsior Springs Job Corps Center in Missouri, solicited through a Request for Quotation with a submission deadline of August 14, 2026, at 12:00 PM CST. The contract requires quarterly inspections of 175 fire extinguishers located across 21 campus buildings and 23 center-owned vehicles, with replacement of used or uncharged units as needed. Each inspection must include the provision of official inspection tags, and all work must comply with NFPA Standard No. 101, the National Electrical Code, OSHA regulations, and applicable local, state, and federal codes. The performance period runs from October 1, 2026, through September 30, 2027, with services rendered four times per year. Pricing is to be submitted via a completed Bid Sheet with a detailed cost breakdown, and no government estimate is provided; award will be based on best overall value, not necessarily the lowest bid. All bidders must hold active Missouri licenses and credentials relevant to fire safety services. The solicitation is set aside for small businesses under SBA programs, including SB, SDB, WOSB, HUBZone SB, VOSB, and SDVOSB, and requires full compliance with several FAR clauses including certification against debarment, the Service Contract Act, Anti-Lobbying Certification, and adherence to minimum wage requirements under Executive Order 14026. Respondents must provide a Vendor Acknowledgement Form, Form W-9, FFATA Notice (if applicable), Anti-Lobbying Certification (if applicable), and valid Certificates of Insurance, including liability, workers’ compensation, and automobile coverage. The winning contractor must maintain an active SAM.gov registration with a Unique Entity ID and follow strict site conduct protocols: no fraternization with students or staff, no tobacco, alcohol, drugs, or firearms on campus, and adherence to all center security rules. Payment is due within 30 days of invoice submission, and all deliveries are F.O.B. destination. Failure to submit any mandatory documentation or meet regulatory conditions will disqualify a bid regardless of pricing structure. Site visits are required prior to submission, and all bid materials must be typewritten or in ink with no erasures, and delivered to the specified address marked with the solicitation title.

ETR/Excelsior Springs Job Corps

POSTED

about 14 hours ago

DEADLINE

IE JCC HVAC Replacements

Solicitation # ie-jcc-hvac-replacements

This solicitation for HVAC replacements at the Inland Empire Job Corps Center in San Bernardino, California, is a subcontracting opportunity managed by Management & Training Corporation on behalf of the U.S. Department of Labor. The contract is a fixed-price, single lump sum arrangement with an estimated value between $25,000 and $100,000, requiring the furnishing and installation of three new packaged HVAC units with gas heating at ground-level or rooftop locations, along with the complete removal and environmentally compliant disposal of existing units per EPA regulations. Scope of work includes reconnecting and modifying existing gas piping and ductwork, installing new electrical disconnects and programmable thermostats, conducting startup and commissioning tests—including verification that fresh air intake dampers shut during fire activation—and delivering full Operation and Maintenance manuals, manufacturer warranties, and recycling documentation. All work must comply with Title 24, the 2024 International Mechanical Code, the 2024 International Energy Conservation Code, and ASHRAE 90.1-2022 standards, and must be completed within 100 consecutive business days following a written Notice to Proceed, which will be issued after an onsite pre-construction meeting where start and end dates are mutually agreed upon. The procurement is reserved exclusively for small business concerns under the SBA’s set-aside program, encompassing Small Business, Small Disadvantaged Business, Women-Owned Small Business, HUBZone Small Business, Veteran-Owned Small Business, and Service-Disabled Veteran-Owned Small Business categories. Offerors must hold a Unique Entity Identifier (UEI) and provide their Tax ID, DUNS number, and NAICS code 238220 (Heating, Air Conditioning, and Refrigeration Contractors). Mandatory compliance elements include submitting a fully executed SF 1413 form, weekly certified payroll reports, adherence to prevailing wage requirements under Executive Order 13658, and disclosure of debarment status for any first-tier subcontractor exceeding $30,000. Bids must include a detailed cost breakdown covering materials, labor, equipment, permits, bonds, overhead, and profit; a bid bond of 20% is required if the bid exceeds $25,000, along with performance and payment bonds at 100% of the contract value if awarded. Insurers must list Management & Training Corporation/DOL/Inland Empire Job Corps as additional insured with one million per occurrence and three million

MTC Inland Empire Job Corps

POSTED

about 14 hours ago

DEADLINE

in about 2 hours

Boiler replacement in IOOF and Administration

Solicitation # boiler-replacement-ioof-administration

The contract seeks a licensed HVAC contractor to replace three boilers across two buildings at the Flint Hills Job Corps Center in Manhattan, Kansas, specifically targeting Building 1 (IOOF) and Building 2 (Administrative/Academic). In Building 1, two existing Peerless gas-fired boilers will be removed and replaced with new hot water gas-fired boilers rated at 1,680,000 B.T.U. input and 1,344,000 B.T.U. output per hour. In Building 2, a new high-efficiency gas-fired boiler meeting Energy Star standards with 600,000 B.T.U. input, 572,000 B.T.U. output, and 94% efficiency will be installed. The work requires full compliance with state of Kansas codes including NEC, NFPA-72, NFPA 101, IBC, IMC, IPC, and IECC, as well as adherence to EPA regulations such as 40 CFR 761 and 40 CFR 61 Subpart M and OSHA’s 29 CFR 1926 standards. A qualified commissioning agent must validate the boiler control systems, and extensive documentation including inspection reports, test results, warranties, commissioning reports, and O&M manuals must be submitted. All piping must be labeled with preformed PVC tags indicating service and directional flow, and materials must be received, stored, and secured by the contractor. The contract is set aside for small business categories including SB, SDB, WOSB, HUBZone SB, VOSB, and SDVOSB under NAICS code 238220. The contractor must hold a current, valid license to operate in Manhattan, Kansas, obtain all necessary permits, and carry liability insurance naming the Center as both certificate holder and additional insured. Labor must comply with the Davis-Bacon Act wage determinations, and all workers must follow strict security and conduct rules, including no fraternization with students or staff, no use of food service facilities, and prohibition on transporting drugs, alcohol, or firearms to the site. Warranties are mandated at ten years for boiler heat exchangers, two years for other parts, and one year for workmanship alongside a one-year preventive maintenance agreement for the Center. Performance must begin within fourteen days of the Notice To Proceed, with substantial completion expected within 60 days and full contract close-out completed within

Serrato Corporation DBA Flint Hills Job Corps

POSTED

about 14 hours ago

DEADLINE

Keystone Lincoln Dorm Water Heater Repair

Solicitation # keystone-lincoln-dorm-water-heater-repair

The contract is for the repair of a specific hot water heater located at the Keystone Job Corps Center in Drums, Pennsylvania, identified as an AquaPlex Turbopower 96, Model #100L400A-TPX, with serial number F008076. The work includes replacing critical components such as the blower motor assembly, gas valve, hot surface ignitor, ignitor gasket, and electrode flame rod. This is a small business set-aside solicitation under the SBA program, open to Small Businesses, Small Disadvantaged Businesses, Women-Owned Small Businesses, HUBZone Small Businesses, Veteran-Owned Small Businesses, and Service-Disabled Veteran-Owned Small Businesses. The NAICS code is 238220, and the contracting activity is managed by Adams & Associates Keystone Red Rock Job Corps. The Davis-Bacon Act wage rates apply, and certified payroll records must be submitted. All offerors are required to be currently registered and active on SAM.gov. Bidders must submit separate line items for labor and materials, though the total contract value, pricing details, and evaluation criteria are not disclosed. The solicitation was posted on August 7, 2026, with a response deadline of August 14, 2026. Performance is required at the Lincoln dormitory on the Keystone Job Corps campus in Pennsylvania. No packaging, marking, delivery schedule, period of performance, or award methodology details are provided. Point of contact for inquiries is Jennie Drumheller, reachable via email and phone.

Adams & Associates Keystone Red Rock Job Corps

POSTED

about 14 hours ago

DEADLINE

PCJCC HVAC Replacement Bldg Two

Solicitation # PCJCC-HVAC Replacement Bldg Two

This subcontracting opportunity is issued by Exceed Corporation LLC on behalf of the Pinellas County Job Corps Center in St. Petersburg, Florida, for the replacement of two outdoor condenser units— one 20 ton and one 15 ton—at Building Two. The work requires a licensed HVAC contractor to remove existing equipment including CU-2-1 and CU-2-2 condensing units and the full length of associated refrigerant line-sets, as well as the DX cooling coil from the existing VAV Air Handling Unit, and install two new commercial-grade split condensing units with new insulated refrigerant lines, filter dryers, refrigerant accumulators, sight glasses, and thermostatic expansion valves. All new equipment must use non-ozone-depleting A2L refrigerants such as R-32 or R-454B, meet current Energy Star and Federal Energy Management Product (FEMP) standards, and comply with EPA, ASHRAE 15, IMC, IPC, SMACNA, NEC, NFPA 90A, and NFPA 72 regulations. The contractor must responsibly recover and manage R-22 refrigerant from the existing units for recycling, reuse, or approved offsite disposal, install new NEMA 3R electrical disconnects, conduit, and wiring, and verify or install duct-mounted smoke detectors per applicable codes. A mandatory site visit must be completed before submitting a bid, and all proposals must include complete pricing for installation, removal, and all ancillary costs with no late submissions accepted after 5 p.m. on August 7, 2026. The contract is reserved exclusively for small business concerns including small disadvantaged, women-owned, HUBZone, veteran-owned, and service-disabled veteran-owned small businesses as defined by the SBA, and all offerors must be EEO compliant. The contractor must provide a minimum five-year compressor warranty and one-year parts and labor warranty, with performance taking place at 500 22nd Street South, St. Petersburg, FL 33712. All work must adhere to manufacturer installation guidelines and the latest codes, and units must be started and operationally tested upon completion. Questions should be directed to Angelia Richardson, Finance & Administration Director, via email or phone.

Exceed, LLC dba Pinellas County Job Corps Center

POSTED

about 14 hours ago

DEADLINE

in about 3 hours

2026-Maui-Dorm Exhaust Fans

Solicitation # 2026- Maui- Dorm Exhaust Fans

This is a subcontracting opportunity with Management and Training Corporation (MTC) for the removal and replacement of approximately 25 exhaust fans across three dormitories at the Hawaii Job Corps Center in Makawao, Hawaii. The solicitation, designated as 2026-maui-dorm-exhaust-fans, is open to small businesses under a set-aside program that includes Small Business, Small Disadvantaged Business, Women-Owned Small Business, HUBZone Small Business, Veteran-Owned Small Business, and Service-Disabled Veteran-Owned Small Business categories, with NAICS code 238220. Bids must be submitted electronically by 3:00 PM HST on August 28, 2026, to Karllene Allen and Mila Handel at specified email addresses, and must include a completed MTC Bid for Lump Sum Contract form signed by an authorized representative, along with a detailed cost breakout covering materials, labor with categories and rates, equipment, permits, disposal, testing, bonds, subcontractor costs, overhead, profit, and other direct or indirect expenses. The contract is fixed-price with a single lump sum payment structure, and all offers must include a bid bond of 20% of the base bid if the total exceeds $25,000, with performance and payment bonds at 100% of contract value required if the bid equals or exceeds this threshold. Bonds must be issued by an A-rated surety and conform to standard forms such as AIA A311, AIA A312, SF25, or SF25A. Contractors must comply with extensive federal and Department of Labor requirements, including adherence to Executive Order 13658 for prevailing wage rates, submission of weekly certified payroll reports, and display of bilingual Davis-Bacon Act posters. All work must be performed at the designated site, and a mandatory physical site visit with signed attendance is required before bid submission. The contractor is responsible for acquiring all necessary permits, managing waste disposal in accordance with local regulations, restoring drywall and plaster to match existing finishes, and providing two complete operation and maintenance manuals with manufacturer data sheets. A minimum of two hours of on-site training for facility personnel is required, and safety data sheets for any hazardous materials used must be provided to MTC. Insurance requirements include $1 million per occurrence/$3 million aggregate general liability with MTC listed as additional insured, $1 million auto liability, $500,00

Management & Training Corporation

POSTED

about 14 hours ago

DEADLINE

HVAC Units Replacement in 3 dormitories

Solicitation # 26-134

The contract mandates the replacement of twenty HVAC units across three dormitory buildings at the Atterbury Job Corps Center in Edinburgh, Indiana, specifically nine units at 1095 MLK, nine at 1094 RFK, and two condensing units at 1963 LBJ. All existing units, which use outdated R-22 refrigerant and are manufactured by Bryant, must be replaced with new 12.5 SEER packaged units utilizing non-R22 refrigerants such as R-410A or R-454B. Contractors are required to reuse existing electrical disconnects, ductwork, and thermostat wiring during installation. All removed units from 1094 and 1095 must be left at the maintenance building for disassembly and parts recovery, and all recovered refrigerant must be properly labeled and handed over to facility maintenance for reuse. The work must comply with state and local codes, EPA regulations for refrigerant handling, and OSHA safety standards. A mandatory bid conference is required for bid eligibility, and only vendors who attend will be considered. Proposals must be submitted as a single lump sum cost on official company letterhead, accompanied by a detailed cost breakdown covering labor, materials, equipment, and incidentals, along with supporting documentation including a completed SF 1413, W9, Vendor Questionnaire with DUNS#, SAM.gov wage determination printout, proof of Indiana contractor’s license, insurance certificates, Small Business Certification if applicable, and copies of all relevant licenses and certifications. The award will be made on a best value basis, with price accounting for 60% of evaluation, quality for 20%, past performance for 10%, and schedule for 10%, with explicit notice that the lowest price does not guarantee award. Bidders must provide a timeline for substantial completion, and work must begin within fourteen days of the Notice to Proceed. The contractor must guarantee all workmanship for one year and ensure all tests are completed, witnessed, and approved by the center’s representative before substantive completion can be certified. A final walk-through will be conducted by the Contracting Officer or designee, and the contractor must submit a written request for inspection at least three days prior to estimated completion. Payment terms are Net 30, and contractors must provide proof of insurance including $1 million general liability, $200,000 per person/$500,000 per occurrence automobile liability with Adams & Associates and At

Adams & Associates, Inc.

POSTED

about 14 hours ago

DEADLINE

in about 1 hour

NJCC Building 32 Boiler Replacement in Vermont

Solicitation # njcc-building-32-boiler-replacement-vermont

The Northlands Job Corps Center in Vergennes, Vermont is soliciting bids for the replacement of a boiler located in Building 32, as outlined in the attached Request for Quote and walkthrough details. The solicitation, issued under the number njcc-building-32-boiler-replacement-vermont, was posted on August 7, 2026, with a response deadline of September 4, 2026. This procurement is set aside for small businesses, including Small Disadvantaged Businesses, Women-Owned Small Businesses, HUBZone Small Businesses, Veteran-Owned Small Businesses, and Service-Disabled Veteran-Owned Small Businesses, under NAICS code 238220 for heating equipment installation and repair. The primary point of contact for inquiries is Jeana Bradford, reachable via email at bradford.jeana@jobcorps.org or by phone at 802-877-0149. All work must be performed at the specified location in Vermont, and interested parties should review the full RFQ for technical specifications, installation requirements, and compliance terms.

Northlands Job Corps Center /ETR

POSTED

about 14 hours ago

DEADLINE

More opportunities from Department Of Defense → DLA Land And Maritime

Same awarding agency

Military Packaging and Preservation ServicesThe contract requires compliance with MIL-STD standards for the preservation, packaging, and marking of sensitive military shipments, ensuring that all materials are protected against environmental damage, corrosion, and physical degradation during transit and storage. The work must adhere strictly to Department of Defense specifications to maintain operational readiness and logistical integrity across the supply chain. This subcontract is issued under NAICS code 561910 and is managed by DLA Land and Maritime under the broader Department of Defense structure. The solicitation was posted on August 6, 2026, with a response deadline of August 21, 2026, at 4:00 p.m. The place of performance and organizational details are not specified, but the performance location will likely involve military logistics hubs or defense supply facilities. All work is expected to support secure and standardized handling of critical defense equipment, with no set-aside designation applied, meaning the opportunity is open to qualified contractors regardless of business size or ownership category.

Packaging and Labeling Services

POSTED

DEADLINE

Phosphate Coating Services for Propeller Shaft ComponentsThe contract requires the provision of military-compliant phosphate coating services specifically for drivetrain components, adhering strictly to the standards outlined in MIL-STD-171 and TT-C-490. These coatings are essential for corrosion resistance, lubricity, and adhesion of subsequent finishes on critical propeller shaft parts used in defense applications. The work must be performed to exacting military specifications to ensure performance, durability, and interoperability within defense systems. This is a subcontract opportunity issued by the Defense Logistics Agency Land and Maritime under the Department of Defense, with a NAICS code of 332813 indicating specialization in metal coating services. The solicitation was posted on August 6, 2026, and responses are due by August 21, 2026. While the place of performance and point of contact details are not specified, the work is expected to support military logistics and maintenance operations, and all services must meet the rigorous quality and compliance criteria mandated by federal defense standards.

Electroplating, Plating, Polishing, Anodizing, and Coloring

POSTED

DEADLINE

Manufacture of Vehicular Propeller Shaft (NSN: 014130080)The contract is for the manufacture and delivery of a second variant of a military propeller shaft designated by NSN 014130080, requiring strict adherence to Qualified Products List and Qualified Manufacturer List sourcing standards to ensure component authenticity and military-grade reliability. The work must include specialized packaging protocols compliant with defense logistics requirements, ensuring protection during transport and storage under harsh environmental conditions. This is a subcontract opportunity issued under the NAICS code 336390, categorized under the Department of Defense through DLA Land and Maritime, with a response deadline of August 21, 2026, and posted on August 6, 2026. The place of performance and point of contact details are not specified, and no set-aside designation is indicated, leaving eligibility open to all qualified subcontractors who can meet the technical and supply chain compliance criteria.

Other Motor Vehicle Parts Manufacturing

POSTED

DEADLINE

Manufacture of Vehicular Propeller Shaft (NSN: 014235120)The contract is for the manufacture and delivery of a military-spec propeller shaft equipped with a universal joint, engineered to meet stringent source control drawings and technical standards applicable to Department of Defense vehicles. The item is identified by NSN 014235120 and falls under NAICS code 336390, indicating it pertains to motor vehicle parts manufacturing. The work must be performed in full compliance with all military specifications to ensure operational reliability and interoperability within defense platforms. The solicitation is classified as a subcontract opportunity posted by DLA Land and Maritime on August 6, 2026, with a response deadline of August 21, 2026. There is no set-aside designation specified, meaning the contract is open to all qualified contractors regardless of size or business type. The place of performance is not detailed, and no point of contact information is provided in the data, but the official solicitation can be accessed through the SAM.gov portal for complete technical and administrative requirements. All deliverables must be fabricated, tested, and documented to meet the exacting standards required for military use.

Other Motor Vehicle Parts Manufacturing

POSTED

DEADLINE

Surveying and Site LayoutThe contract titled Surveying and Site Layout is a subcontract under the NAICS code 541370, issued by the Department of Defense through DLA Land and Maritime, requesting services related to the establishment of site control points, precise layout of structures, and as-built verification to ensure alignment with design specifications. The solicitation was posted on August 6, 2026, with a deadline for responses set for August 12, 2026, at 7:00 PM, indicating a narrow window for submission. The work involves high-precision surveying activities critical to construction accuracy, requiring qualified professionals capable of delivering reliable geospatial data throughout the project lifecycle. The place of performance and point of contact information are not specified, suggesting that the exact location and direct liaison will be determined upon award or communicated directly to selected subcontractors. This effort supports defense infrastructure projects where dimensional accuracy and documentation integrity are paramount.

Surveying and Mapping (except Geophysical) Services

POSTED

DEADLINE

Paving and Asphalt SurfacingThe contract solicits subcontracting services for grading, base preparation, and asphalt paving work to be performed on roadways, parking areas, and access roads under the NAICS code 237310. The opportunity is managed by the Department of Defense through DLA Land and Maritime, with responses due by August 12, 2026, at 7:00 PM, following a posting date of August 6, 2026. No set-aside provisions are specified, and the place of performance details, including city, state, or zip code, are not provided in the data. The work involves comprehensive pavement construction from site preparation through final asphalt surfacing, requiring adherence to technical and quality standards typical of federal infrastructure projects. The submission deadline is firm, and interested parties must respond through the designated SAM.gov portal before the due date to be considered.

Highway, Street, and Bridge Construction

POSTED

DEADLINE

Concrete Forming and PlacementThe contract entitled Concrete Forming and Placement encompasses the full scope of formwork installation, reinforcement assembly, and concrete pouring for structural elements including foundations, walls, and slabs, all performed to meet precise engineering and safety standards. The work is classified under NAICS code 238110, indicating it falls under the specialty trade contractor category for concrete work, and is issued as a subcontract under the Department of Defense through DLA Land and Maritime. The opportunity was posted on August 6, 2026, with a strict response deadline of August 12, 2026, at 7:00 PM, leaving a narrow window for qualified firms to submit proposals. While the exact location of performance remains unspecified in the data provided, the project is tied to a federal defense installation and requires compliance with all applicable Department of Defense construction protocols, material specifications, and quality assurance requirements. No set-aside provisions are indicated, meaning the contract is open to all eligible subcontractors without restrictions based on business size or ownership type.

Poured Concrete Foundation and Structure Contractors

POSTED

DEADLINE

Electrical Installation and Wiring ServicesThe contract titled Electrical Installation and Wiring Services pertains to the execution of electrical systems for commercial or infrastructure projects, encompassing the installation of wiring, conduits, lighting, and power distribution components. It is issued as a subcontract under the NAICS code 238210, which classifies electrical contracting activities, and is managed by the Department of Defense through its DLA Land and Maritime division. The solicitation was posted on August 6, 2026, with a response deadline set for August 12, 2026, at 7:00 PM, indicating a narrow window for interested parties to submit proposals. The place of performance and detailed office address are unspecified, suggesting the scope may span multiple locations or will be determined post-award. While no set-aside provisions or point of contact information are provided, the involvement of a federal agency underscores the need for compliance with defense contracting standards and likely requires certified electrical contractors with proven experience in large-scale, secure, or mission-critical infrastructure.

Electrical Contractors and Other Wiring Installation Contractors

POSTED

DEADLINE

59--TRANSFORMER,POWER AUTO

Solicitation # SPE7M126U5062

The U.S. Department of Defense through DLA Land and Maritime is soliciting quotes for 145 units of NSN 5950003483796, a power auto transformer, with delivery required within 124 days of award. This solicitation may lead to an indefinite delivery contract lasting one year or until the cumulative order value reaches $350,000, with an estimated two annual orders and a guaranteed minimum of 21 units. Deliveries will be distributed to multiple DLA depots across CONUS and OCONUS via consolidated and containerized shipping points. Only approved sources—identified by vendor codes 16157 3588, 51181 K7174, and 72914 55-0504-1—are eligible to respond. The solicitation is issued as an RFQ under NAICS code 334417 and is accessible exclusively online via the SAM.gov link; no hard copies or technical specifications are available. All responsible vendors may submit electronic quotes by the deadline of August 21, 2026, with inquiries directed to the designated point of contact email.

Electronic Connector Manufacturing

POSTED

DEADLINE

29--PUMP,HAND,FUEL PUMP

Solicitation # SPE7L526T4904

The U.S. Department of Defense, through DLA Land and Maritime, is seeking quotations for 294 hand fuel pumps with NSN 2910014705545 under solicitation number SPE7L526T4904, which is a Small Business Set Aside with no small business size standard applied. The procurement is exclusively for responsible sources, and all quotes must be submitted electronically by the deadline of August 17, 2026. Delivery is required to W1A8 DLA Distribution within 153 days after award, and the approved source for this item is 15852 AP00314. The solicitation is issued as a combined solicitation, and no hard copies or detailed specifications, plans, or drawings are available. The North American Industry Classification System code for this requirement is 336310, and inquiries must be directed via email to the designated point of contact at DibbsBSM@dla.mil, with the full solicitation document accessible only through the Sam.gov portal.

Motor Vehicle Gasoline Engine and Engine Parts Manufacturing

POSTED

DEADLINE

47--HOSE ASSEMBLY,NONMETAL

Solicitation # SPE7M426T320D

The contract solicitation is for the procurement of 11 units of a nonmetal hose assembly with NSN 4720012482251, to be delivered to DLA Distribution Cherry Point within 154 days after order placement. This is a source-controlled item requiring parts to be manufactured exclusively by the approved sources listed as 78570 and 99193, both using drawing number 3886075-2. All supplied items must strictly conform to the technical specifications detailed in the referenced drawing, and digitized versions of the drawing and associated military standards can be accessed electronically. The solicitation, identified as SPE7M426T320D, was posted on August 6, 2026, with quotes due by August 17, 2026, and is exclusively available online through the provided URL; no hard copies are distributed. Submission of quotes is mandatory through electronic means, and all responsible suppliers are invited to respond. The procurement is managed by the DLA Land and Maritime office in Columbus, Ohio, with all inquiries directed to the designated point of contact via email.

Fabric Coating Mills

POSTED

DEADLINE

59--SWITCH,PRESSURE

Solicitation # SPE7M526T374F

The U.S. Department of Defense, through DLA Land and Maritime, is soliciting quotes for 11 units of the pressure switch with NSN 5930008400253, to be delivered to DLA Distribution Depot Oklahoma within 168 days of award. This procurement is conducted under solicitation number SPE7M526T374F, which was posted on August 6, 2026, with responses due by August 17, 2026. Only approved sources—09049 42D49C and 81205 10-3269-10—are eligible to respond, and all quotations must be submitted electronically through the SAM.gov portal; hard copies are not accepted. No technical specifications, plans, or drawings are provided, and the solicitation is open to all responsible sources that submit timely quotes. The procurement falls under NAICS code 332919 and is managed from the office in Columbus, Ohio. Any questions must be directed via email to the designated point of contact listed in the solicitation document, accessible through the provided link or via the DIBBS website using the solicitation number.

Other Metal Valve and Pipe Fitting Manufacturing

POSTED

DEADLINE