STARTER, ENGINE, ELEC

STARTER,ENGINE,ELEC
STARTER, ENGINE, ELECTRICAL.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
CUMMINS POWER GENERATION INC. 44940 P/N 3604677RX
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017677297 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
SPE7L1-26-T-901X
SECTION B
PR: 7017677297 PRLI: 0001 CONT’D
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING
MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT
PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE.
DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED
WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS
AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT
CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC DIE-CUT) SHALL BE
WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL
IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER
COLLAPSE, AND INCREASE STACKING STRENGTH OF
CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W80XYJ
0553 CS BN CO A COMPOSITE
AWCF SSF
BLDG 40054 MOTOR POOL ROAD
FORT HOOD TX 76544
US
SPE7L1-26-T-901X
SECTION B
PR: 7017677297 PRLI: 0001 CONT’D
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W80XYJ
0553 CS BN CO A COMPOSITE
AWCF SSF
BLDG 40054 MOTOR POOL ROAD
FORT HOOD TX 76544
US
MARKFOR
W80XYJ
0553 CS BN CO A COMPOSITE
AWCF SSF
BLDG 40054 MOTOR POOL ROAD
FORT HOOD TX 76544
US
M/F: (TCN) W80XYJ61120246
RDD: N
PROJ: TP 1
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 02
DIC: A0A DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:04/27/2026

DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0002 7017677295 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
SPE7L1-26-T-901X
SECTION B
PR: 7017677295 PRLI: 0001 CONT’D
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
SPE7L1-26-T-901X
SECTION B
PR: 7017677295 PRLI: 0001 CONT’D
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
SPE7L1-26-T-901X
SECTION B
PR: 7017677295 PRLI: 0001 CONT’D
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
SHIP BY TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
MARKFOR
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
M/F: (TCN) W4546F61010418
RDD: 114
PROJ: TP 3
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 12
DIC: A0A DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:04/16/2026

DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0003 7017689981 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
SPE7L1-26-T-901X
SECTION B
PR: 7017689981 PRLI: 0001 CONT’D
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
SPE7L1-26-T-901X
SECTION B
PR: 7017689981 PRLI: 0001 CONT’D
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
SPE7L1-26-T-901X
SECTION B
PR: 7017689981 PRLI: 0001 CONT’D
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
SPE7L1-26-T-901X
SECTION B
PR: 7017689981 PRLI: 0001 CONT’D
BULK BREAK POINT:
W33MMS
W8RX GA ARNG FMS 1
935 EAST UNITED AVE SE
BLDG 16
ATLANTA GA 30316-0882
US
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W90PKG
W8RX GA ARNG FMS 1
935 E UNITED AVE SE
BLDG 16
ATLANTA GA 30316-0882
US
MARKFOR
W90PKG
W8RX GA ARNG FMS 1
935 E UNITED AVE SE
BLDG 16
ATLANTA GA 30316-0882
US
M/F: (TCN) W90PKG60980013
RDD: N
PROJ: TP 1
SUPP ADD: W81K57 SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 03
DIC: A3A DIST: ADV: FC: 62
Need Ship Date:00/00/0000 Original Required Delivery Date:04/13/2026

DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0004 7017689710 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
SPE7L1-26-T-901X
SECTION B
PR: 7017689710 PRLI: 0001 CONT’D
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
SPE7L1-26-T-901X
SECTION B
PR: 7017689710 PRLI: 0001 CONT’D
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
SPE7L1-26-T-901X
SECTION B
PR: 7017689710 PRLI: 0001 CONT’D
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
SPE7L1-26-T-901X
SECTION B
PR: 7017689710 PRLI: 0001 CONT’D
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
SPE7L1-26-T-901X
SECTION B
PR: 7017689710 PRLI: 0001 CONT’D
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W81B9W
0524 CS BN CO A COMPOSITE
DSU OPS AWCF SSF
BLDG 3005 LYMAN RD
SCHOFIELD BARRACKS HI 96857-5200
US
RDD 999/NMCS SHIPMENT. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANS SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W81B9W
0524 CS BN CO A COMPOSITE
DSU OPS AWCF SSF
BLDG 3005 LYMAN RD
SCHOFIELD BARRACKS HI 96857-5200
US
MARKFOR
W81B9W
0524 CS BN CO A COMPOSITE
DSU OPS AWCF SSF
BLDG 3005 LYMAN RD
SCHOFIELD BARRACKS HI 96857-5200
US
M/F: (TCN) W81B9W61180464
RDD: 999
PROJ: TP 1
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 02
DIC: A01 DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:05/01/2026
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0005 7017678479 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
SPE7L1-26-T-901X
SECTION B
PR: 7017678479 PRLI: 0001 CONT’D
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
MARKFOR
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
M/F: (TCN) W91CNC62030079
RDD: 218
PROJ: 9GU TP 3
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 12
DIC: A01 DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:07/27/2026
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0006 7017678478 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
SPE7L1-26-T-901X
SECTION B
PR: 7017678478 PRLI: 0001 CONT’D
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
MARKFOR
W91CNC
W6J6 USAREUR-AF SSA UASL
EUR TSSA BLDG7956 GERMERSHEIM AWCF
VORWERK FRIEDRICH STR 07274 965547
LINGENFELD 67360
DE
M/F: (TCN) W91CNC61970069
RDD: 212
PROJ: 9GU TP 3
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 12
DIC: A01 DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:07/21/2026

SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0007 7017678172 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W45J67
0115 CS BN CO A DISTRIBUTI
AWCF SSF A CO 115 BSB SSA
BLDG 38042 TURKEY RUN ROAD
FORT HOOD TX 76544
US
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W45J67
0115 CS BN CO A DISTRIBUTI
AWCF SSF A CO 115 BSB SSA
BLDG 38042 TURKEY RUN ROAD
FORT HOOD TX 76544
US
MARKFOR
W45J67
0115 CS BN CO A DISTRIBUTI
AWCF SSF A CO 115 BSB SSA
BLDG 38042 TURKEY RUN ROAD
FORT HOOD TX 76544
US
M/F: (TCN) W45J6761170126
RDD: N
PROJ: TP 1
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 02
DIC: A0A DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:04/30/2026

SPE7L1-26-T-901X
SECTION B
PR: 7017678172 PRLI: 0001 CONT’D
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0008 7017678171 0001 EA 1.000
NSN/MATERIAL:2920014709867
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED
PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS
AWAY FROM CONTAINER SURFACES TO PROTECT FROM
IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT
CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT
ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC.
WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE
AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:41 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:EA CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:C
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
1. WRAP PRESERVED PRODUCT WITH SPECIFIED WRAPPING MATERIAL IN AREAS WHERE DIE-CUT WILL CONTACT PRODUCT. SECURE WRAPPING MATERIAL WITH TAPE. DO NOT APPLY TAPE DIRECTLY ON PRODUCT.
2. PLACE WRAPPED PRODUCT INSIDE SPECIFIED WATERVAPORPROOF BARRIER BAG, THEN REMOVE EXCESS AIR AND HEAT SEAL. APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION MARKINGS TO THIS BAG.
3. CUSHIONING MATERIAL (CODE: JC - DIE-CUT) SHALL BE WEATHER-RESISTANT FIBERBOARD DIE-CUTS AND SHALL IMMOBILIZE AND PROTECT PRODUCT, PREVENT CONTAINER COLLAPSE, AND INCREASE STACKING STRENGTH OF CONTAINER.
DIE-CUT SHALL SNUGGLY NEST PRESERVED AND WRAPPED PRODUCT. DIE-CUT SHALL LIFT PRODUCT AND PROTRUSIONS AWAY FROM CONTAINER SURFACES TO PROTECT FROM IMPACTS.
PLACEMENT OF DIECUTS SHALL BE AGAINST AREAS THAT CAN WITHSTAND PRODUCT WEIGHT DISTRIBUTION WITHOUT ANY DAMAGE OR WEAKENING OF SOLDER, JOINTS, ETC. WEIGHT SHALL BE DISTRIBUTED OVER LARGER SURFACE AREA TO REDUCE STATIC STRESS.
NOTE: THIS DESIGN WILL DISTRIBUTE WEIGHT EVENLY.
4. UNIT CONTAINER SHALL BE WEATHER-RESISTANT CORRUGATED
FIBERBOARD; AND CONTAINER FLAPS SHALL BE REINFORCED
TO STRENGTHEN THE BOTTOM OF THE CONTAINER. FIBERBOARD
CONTAINER SHALL HAVE A MANUFACTURER'S CERTIFICATE TO
VERIFY CONTAINER MATERIAL AND STRUCTURAL PROPERTIES.
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D
PLACE WRAPPED AND CUSHIONED PRODUCT INSIDE THE
SPECIFIED UNIT CONTAINER, SECURE CLOSURE, AND
APPLY MIL-STD-129 UNIT CONTAINER IDENTIFICATION
MARKINGS TO THIS CONTAINER.
PACKAGE DESIGN SHALL IMMOBILIZE PRODUCT WITHIN THE
CONTAINER TO ADEQUATELY PACKAGE AND PROTECT ITEM.
PACKAGE DESIGN PERFORMANCE CRITERIA IS SAFE DELIVERY
OF PRODUCT TO ULTIMATE USER. PRODUCT MUST ARRIVE IN
SERVICEABLE CONDITION.
ZZ SPECIAL MARKING REQUIREMENTS:
02 ARROW UP
OPEN THIS SIDE
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
BULK BREAK POINT:
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
SHIP BY TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
MARKFOR
W4546F
0123 CS BN CO A DISTRIBUTI
US ARMY 0123 CS BN CO A DISTRIBUTI
BLDG 23010 REDBALL EXPRERSS
FORT BLISS TX 79918-0000
US
M/F: (TCN) W4546F61950396
RDD: 208
PROJ: TP 3
SUPP ADD: W9046W SIG: C
FOR GOVERNMENT USE ONLY: (IPD) 12
DIC: A0A DIST: V ADV: FC: Z9
Need Ship Date:00/00/0000 Original Required Delivery Date:07/17/2026
SPE7L1-26-T-901X
SECTION B
PR: 7017678171 PRLI: 0001 CONT’D

SPE7L1-26-T-901X NSN/Part Number: 2920-01-470-9867 Quantity: 1 EA Purchase Request: 7017678172QTY: 1 Delivery: 5 days ADO