CYLINDER ASSEMBLY, HYDR

CYLINDER ASSEMBLY,HYDRAULIC BRAKE,WHEEL
CYLINDER ASSEMBLY, HYDRAULIC BRAKE, WHEEL
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
FULL AND OPEN COMPETITION APPLY
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
MANUFACTURERS LIST (QML)" APPLY.
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information.
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
"REFERENCE MATERIAL-INCLUDES HANDBOOKS,
MANUALS, PRICE LISTS, REGISTRIES, DIRECTORIES,
BOOKS, ETC."
This item contains a phosphate coating requirement IAW MIL-STD-171, MIL-DTL-16232, and TT-C-490 Types I, II, and V. In
SPE7L3-27-T-2457
SECTION B
lieu of the required submittal of a preproduction phosphate procedure the following is now required: The contractor responsible for the actual coating procedure must be certified by the Performance Review Institute (PRI) to the NADCAP standard for the phosphate chemical processes. Verification of this certification is required and must be supplied upon request of the Contracting Officer.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RT001: MEASURING AND TEST EQUIPMENT
RQ042: Non-Tailored Higher-Level Quality Requirements (ISO 9001:2015) for Manufacturers and Non-Manufacturers
THE ITEM DESCRIBED IN THIS SOLICITATION
IS DEFINED IN WHOLE OR IN PART BY ARMY
DRAWING(S). THESE DRAWING(S) MAY CONTAIN
A PAINT FINISHING REQUIREMENT. WHERE SUCH
REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING
16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE
MENTS OF THE ARMY DRAWING(S). THIS DRAWING
CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT
RESISTANT COATINGS (CARC), AND ADDITIONAL
INFORMATION RELATING TO HIGH TEMPERATURE
COATINGS.
WHEN FIRST ARTICLE IS REQUIRED IN THE
CONTRACT, THE CONTRACTOR SHALL MARK THE OUTER
SHIPPING CONTAINER IN 2 INCH BOLD, RED LETTERS
"FIRST ARTICLE". THE CONTRACTOR SHALL ALSO
PROVIDE THE TESTING FACILITY WRITTEN
NOTIFICATION OF WHEN THE FIRST ARTICLES
EXHIBITS WILL BE SHIPPED TWO WEEKS BEFORE THE
SHIP DATE.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
This contract includes a requirement for Government fit verification testing, which consists of testing the First Article unit(s) on the next higher assembly for form, fit, and function. The contractor shall prepare and submit the following: (a) first article exhibits (b) test report showing actual results in accordance with data item description DI-NDTI-80809B, entitled, "Test/ Inspection Report;" (c) material certifications
SPE7L3-27-T-2457
SECTION B
(d) process operations sheets (e) copies of drawings used during manufacturing The Government form, fit and function test time are included within the First Article test time parameters. Vendor is advised that manufacture of production quantity prior to receiving Contracting Officer's acceptance of test samples is not advised and is solely at the risk of the vendor.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
Casting/forging may be required to manufacture this NSN and tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains contact@example.gov.
RS020: Shelf-life requirement RS001 for a TYPE I (CODE Q) item with a shelf life of 36 months (non-extendable) applies to this item.
CONTRACTOR FIRST ARTICLE TEST APPLIES IAW DWG 7412065:
-100 PECENT DIMENSIONAL INSPECTIONS.
-MATERIAL CERTIFICATIONS IAW NOTE 2.
-FINISH CERTIFICATION PER NOTE 4.
-PERFORMANCE REQUIREMENTS PER NOTE 3.
-PACKAGING REQUIREMENTS PER NOTE 9.
-IAW QAPS 8720523, 8720527, 7373260 WILL BE PART OF
REQUIRED INSPECTION/TESTING FOR THIS ITEM.
PER DWG 7412065, REV N, NOTE 9, BLEEDER PN: 7373260 MUST BE PACKAGED
SEPERATELY WITH EACH PN: 7412065 CYLINDER ASSEMBLY.
MANUFACTURE IAW DWG 7412065, REV N. PER DWG 7412065, REV N, NOTE 11,
DRAWINGS IN THE TABLE ARE PROVIDED AS REFERNCE ONLY.
CRITICAL APPLICATION ITEM
TDP Rev B Gen 2 IAW BASIC DRAWING NR 19207 7412065 REVISION NR N DTD 09/23/2025 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720521 REVISION NR E DTD 12/13/1994 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 7412067 REVISION NR H DTD 01/19/1993 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720512 REVISION NR F DTD 07/30/2009 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720527 REVISION NR F DTD 09/25/1974 PART PIECE NUMBER:
SPE7L3-27-T-2457
SECTION B
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8733913 REVISION NR C DTD 01/18/1963 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8733924 REVISION NR H DTD 03/23/1966 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720526 REVISION NR B DTD 02/05/1993 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720523 REVISION NR F DTD 06/16/1993 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8720525 REVISION NR D DTD 02/05/1993 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 7373260 REVISION NR K DTD 07/30/2009 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE QAP 16236 SQAPCARCLTPHOS81361 REVISION NR DTD 12/01/2017 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE QAP 16236 CDRL-81361CARPH-17272 REVISION NR DTD 12/01/2017 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 19207 8733929 REVISION NR DTD 12/04/2025 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE SPEC NR MIL-PRF-46176B NOT 3 REVISION NR B DTD 02/09/2021 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE SPEC NR MIL-DTL-14055H REVISION NR H DTD 08/14/2020 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE SPEC NR MIL-DTL-53030D(1) NOT 2 REVISION NR D DTD 11/02/2022 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE STD NR MIL-STD-129R(3) REVISION NR R DTD 02/25/2023 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE NON GOVT STD SSPC-PAINT 25 REVISION NR DTD PART PIECE NUMBER:
SPE7L3-27-T-2457
SECTION B
TDP Rev B Gen 2 IAW REFERENCE NON GOVT STD SSPC-PAINT 25 ED. CHANGES REVISION NR DTD PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7019021904 0001 EA 112.000
NSN/MATERIAL:2530007412065
DELIVERY (IN DAYS):0260
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:50 CLNG/DRY:1 PRESV MAT:ZZ
WRAP MAT:GB CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:B
UNIT CONT:ED OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:016
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:32 -32 Type I, shelf life
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
ATTENTION: SPECIAL REQUIREMENTS
METHOD OF PRESERVATION 50: DISSCANT IS REQUIRED TO CONTROL HEAT-SEALED BARRIER BAG ENVIRONMENT AND ENSURE RUBBER BOOT AND GASKET DOES NOT DETERIORATE. DISSCANT SHALL NOT BE PLACED IN DIRECT CONTACT WITH ANY PARTS, BUT SHALL BE PLACED INSIDE THE WATERVAPORPROOF BARRIER BAG.
Z CLEANING/DRYING: PER DRAWING 7412065, NOTE 4: ALL EXPOSED METALLIC SURFACES EXCEPT MACHINED SURFACES: CLEAN IAW TT-C-490 TREAT TYPE I OR IAW TT-C-490.
ZZ PRESERVATIVE MATERIAL: PER DRAWING 7412065, NOTE 9: PACKAGING FOR SHIPMENT: PLACE IN SEALED BAG WITH RUST INHIBITOR. SCREW, BLEEDER 7373260 MUST BE PACKAGED SEPARATELY WITH EACH 7412065 CYLINDER ASSEMBLY. PACKAGE PARTS IN SPECIFIED CARTON, THEN MARK AND BAR CODE IAW MIL-STD-129.
ATTENTION:
SPE7L3-27-T-2457
SECTION B
PR: 7019021904 PRLI: 0001 CONT’D
EACH PART (SCREW, BLEEDER 7373260, AND 7412065 CYLINDER)
SHALL BE INDIVIDUALLY & PROPERLY PRESERVED, WRAPPED,
CUSHIONED, BAGGED, AND MARKED, PRIOR TO BEING PLACED
INSIDE THE "ED" UNIT CONTAINER AS ONE ASSEMBLY.
PLACE HEAVIEST PART IN THE BOTTOM OF THE CONTAINER.
UNIT CONTAINER SHALL BE A SNUG FITTING CONTAINER TO
RESTRICT MOVEMENT WITHIN CONTAINER.
PER DRAWING 7412065, NOTE 2.E: INTERNAL COMPONENTS AND
INTERNAL SURFACE OF CYLINDER BORE SHALL BE COATED WITH
SILICONE BRAKE FLUID IAW MIL-PRF-46176.
PER DRAWING 7412065, NOTE 2.F: UNLESS SUITABLY PROTECTED
AGAINST ELECTROLYTIC CORROSION, DISSIMILAR METALS AS
DEFINED IN MIL-STD-889 SHALL NOT BE USED IN DIRECT
CONTACT WITH EACH OTHER.
PER DRAWING 7412065, NOTE 12: INSTALL SHIPPING PLUG
IAW 8720512 OR NAS847.
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PARCEL POST ADDRESS:
SW3215
DLA DISTRIBUTION BARSTOW
CENTRAL RECEIVING WHSE 7
REC OFFICER +1 (555) 000-0000
BARSTOW CA 92311-5014
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3215
DLA DISTRIBUTION BARSTOW
CENTRAL RECEIVING WHSE 7
REC OFFICER +1 (555) 000-0000
BARSTOW CA 92311-5014
US
Need Ship Date:11/09/2026 Original Required Delivery Date:08/02/2027
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
SPE7L3-27-T-2457
SECTION B
PR: 7019021904 PRLI: 0002 CONT’D
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0002 7019021904 0002 EA 1,095.000
NSN/MATERIAL:2530007412065
DELIVERY (IN DAYS):0260
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:50 CLNG/DRY:1 PRESV MAT:ZZ
WRAP MAT:GB CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:B
UNIT CONT:ED OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:016
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:32 -32 Type I, shelf life
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
ATTENTION: SPECIAL REQUIREMENTS
METHOD OF PRESERVATION 50: DISSCANT IS REQUIRED TO CONTROL HEAT-SEALED BARRIER BAG ENVIRONMENT AND ENSURE RUBBER BOOT AND GASKET DOES NOT DETERIORATE. DISSCANT SHALL NOT BE PLACED IN DIRECT CONTACT WITH ANY PARTS, BUT SHALL BE PLACED INSIDE THE WATERVAPORPROOF BARRIER BAG.
Z CLEANING/DRYING: PER DRAWING 7412065, NOTE 4: ALL EXPOSED METALLIC SURFACES EXCEPT MACHINED SURFACES: CLEAN IAW TT-C-490 TREAT TYPE I OR IAW TT-C-490.
ZZ PRESERVATIVE MATERIAL: PER DRAWING 7412065, NOTE 9: PACKAGING FOR SHIPMENT: PLACE IN SEALED BAG WITH RUST INHIBITOR. SCREW, BLEEDER 7373260 MUST BE PACKAGED SEPARATELY WITH EACH 7412065 CYLINDER ASSEMBLY. PACKAGE PARTS IN SPECIFIED CARTON, THEN MARK AND BAR CODE IAW MIL-STD-129.
ATTENTION: EACH PART (SCREW, BLEEDER 7373260, AND 7412065 CYLINDER) SHALL BE INDIVIDUALLY & PROPERLY PRESERVED, WRAPPED, CUSHIONED, BAGGED, AND MARKED, PRIOR TO BEING PLACED INSIDE THE "ED" UNIT CONTAINER AS ONE ASSEMBLY.
PLACE HEAVIEST PART IN THE BOTTOM OF THE CONTAINER. UNIT CONTAINER SHALL BE A SNUG FITTING CONTAINER TO RESTRICT MOVEMENT WITHIN CONTAINER.
PER DRAWING 7412065, NOTE 2.E: INTERNAL COMPONENTS AND INTERNAL SURFACE OF CYLINDER BORE SHALL BE COATED WITH SILICONE BRAKE FLUID IAW MIL-PRF-46176.
SPE7L3-27-T-2457
SECTION B
PR: 7019021904 PRLI: 0002 CONT’D
PER DRAWING 7412065, NOTE 2.F: UNLESS SUITABLY PROTECTED
AGAINST ELECTROLYTIC CORROSION, DISSIMILAR METALS AS
DEFINED IN MIL-STD-889 SHALL NOT BE USED IN DIRECT
CONTACT WITH EACH OTHER.
PER DRAWING 7412065, NOTE 12: INSTALL SHIPPING PLUG
IAW 8720512 OR NAS847.
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:50 CLNG/DRY:1 PRESV MAT:ZZ
WRAP MAT:GB CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:B
UNIT CONT:ED OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:016
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:32 -32 Type I, shelf life
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
ATTENTION: SPECIAL REQUIREMENTS
METHOD OF PRESERVATION 50: DISSCANT IS REQUIRED TO CONTROL HEAT-SEALED BARRIER BAG ENVIRONMENT AND ENSURE RUBBER BOOT AND GASKET DOES NOT DETERIORATE. DISSCANT SHALL NOT BE PLACED IN DIRECT CONTACT WITH ANY PARTS, BUT SHALL BE PLACED INSIDE THE WATERVAPORPROOF BARRIER BAG.
Z CLEANING/DRYING: PER DRAWING 7412065, NOTE 4: ALL EXPOSED METALLIC SURFACES EXCEPT MACHINED SURFACES: CLEAN IAW TT-C-490 TREAT TYPE I OR IAW TT-C-490.
ZZ PRESERVATIVE MATERIAL: PER DRAWING 7412065, NOTE 9: PACKAGING FOR SHIPMENT: PLACE IN SEALED BAG WITH RUST INHIBITOR. SCREW, BLEEDER 7373260 MUST BE PACKAGED SEPARATELY WITH EACH 7412065 CYLINDER ASSEMBLY. PACKAGE PARTS IN SPECIFIED CARTON, THEN MARK AND BAR CODE IAW MIL-STD-129.
ATTENTION: EACH PART (SCREW, BLEEDER 7373260, AND 7412065 CYLINDER) SHALL BE INDIVIDUALLY & PROPERLY PRESERVED, WRAPPED, CUSHIONED, BAGGED, AND MARKED, PRIOR TO BEING PLACED INSIDE THE "ED" UNIT CONTAINER AS ONE ASSEMBLY.
PLACE HEAVIEST PART IN THE BOTTOM OF THE CONTAINER. UNIT CONTAINER SHALL BE A SNUG FITTING CONTAINER TO RESTRICT MOVEMENT WITHIN CONTAINER.
PER DRAWING 7412065, NOTE 2.E: INTERNAL COMPONENTS AND INTERNAL SURFACE OF CYLINDER BORE SHALL BE COATED WITH SILICONE BRAKE FLUID IAW MIL-PRF-46176.
PER DRAWING 7412065, NOTE 2.F: UNLESS SUITABLY PROTECTED AGAINST ELECTROLYTIC CORROSION, DISSIMILAR METALS AS DEFINED IN MIL-STD-889 SHALL NOT BE USED IN DIRECT CONTACT WITH EACH OTHER.
PER DRAWING 7412065, NOTE 12: INSTALL SHIPPING PLUG IAW 8720512 OR NAS847.
SPE7L3-27-T-2457
SECTION B
PR: 7019021904 PRLI: 0002 CONT’D
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:05/30/2025 Original Required Delivery Date:08/02/2027

CONTRACTOR FIRST ARTICLE TEST THE NUMBER OF UNITS SHOWN SIGNIFIES THE
TEST REQUIREMENT. SEE FAR CLAUSE 52.209-3 CITED IN SECTION A OF THIS
SOLICITATION FOR THE ACTUAL QUANTITY REQUIRED.
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0003 0000000000 EA 1.000
NSN/MATERIAL:0001S00000053
DELIVERY (IN DAYS):0090
THIS LINE ITEM SIGNIFIES THE FIRST ARTICLE TEST REQUIREMENT (FAT). SEE
CLAUSES FOR INFORMATION CONCERNING THE FAT REQUIREMENT. OFFERS THAT DO
NOT CITE A PRICE FOR THIS LINE ITEM SHALL BE EVALUATED UNDER THE
ASSUMPTION THAT THERE IS NO SEPARATE CHARGE FOR THE FAT. IN THE EVENT
THE FAT REQUIREMENT IS WAIVED, NO AWARD WILL BE MADE FOR THIS LINE ITEM.
SPE7L3-27-T-2457
SECTION B
PR: PRLI: CONT’D
THE NUMBER OF UNITS SHOWN APPEARS AS “1 EA”. THIS QUANTITY SIGNIFIES
THE TEST REQUIREMENT. OFFERORS WILL FIND THE ACTUAL QUANTITY REQUIRED
BY THE GOVERNMENT FOR THE FAT LINE ITEM PER FAR 52.209-3 OR 52.209-4 IN
SECTION A OF THIS SOLICITATION.
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
Need Ship Date:00/00/0000 Original Required Delivery Date:00/00/0000

SPE7L3-27-T-2457 NSN/Part Number: 2530-00-741-2065 Quantity: 112 EA Purchase Request: 7019021904QTY: 1207 Delivery: 260 days ADO